This document specifies the performance requirements for fluxes in solid, liquid and paste forms
intended for use with soft solders.
NOTE 1 ISO 9454-1 specifies the requirements for labelling and packaging as well as the coding system for the
classification of the fluxes.
NOTE 2 Some of the fluxes intended for inert gas and vapour phase soldering may not pass some of the criteria
in Tables 1 and 2.
Requirements for these fluxes are agreed between the purchaser and the supplier.

    • sale 10% off
    • Standard
      14 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      11 pages
      English language
    • e-Library read for
      1 day

The principle of the method specified is to distil a prepared flux solution with sodium hydroxide to expel the ammonia present in the flux, to pass the resulting distillate into a standard sulfuric acid solution, to titrate the excess acid with sodium hydroxide solution and to calculate the ammonia content of the flux. Applies to fluxes of class 3.1.1 only, as defined in ISO 9454-1.

    • sale 10% off
    • Standard
      13 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      10 pages
      English language
    • e-Library read for
      1 day

This document specifies a qualitative method for assessing the aggressiveness of a flux towards copper.
The test is applicable to all fluxes of type 1 as defined in ISO 9454-1.

    • sale 10% off
    • Standard
      11 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      8 pages
      English language
    • e-Library read for
      1 day

This document outlines the equipment and operator qualification needed for laser-arc hybrid welding, and recommends butt, fillet and flange joint preparations and consumables suitable for use with this process. It also gives an overview of the steps to take during equipment set-up, procedure specification, workpiece set-up immediately prior to welding, and after welding once inspecting and testing the welds. This document applies to laser-arc hybrid welding of steels, aluminium and its alloys. T...view more

    • sale 15% off
    • Standard
      12 pages
      English language
    • sale 15% off
    • Standard
      12 pages
      French language
    • sale 15% off
    • Draft
      12 pages
      French language
    • sale 15% off
    • Draft
      13 pages
      English language
    • sale 15% off
    • Draft
      14 pages
      French language
    • sale 15% off
    • Draft
      13 pages
      English language

This document specifies the requirements for chemical composition for soft solder alloys containing
two or more of: tin, lead, antimony, copper, silver, bismuth, zinc, indium and/or cadmium.
An indication of the forms generally available is also included.

    • sale 10% off
    • Standard
      21 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      17 pages
      English language
    • e-Library read for
      1 day

This series of standards applies to welding of metallic materials in the manufacture and maintenance of railway vehicles and their components.
This part of the series defines the classification levels as well as the requirements for manufacturers of welded railway vehicles and components.

    • sale 10% off
    • Standard
      28 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      28 pages
      English language
    • e-Library read for
      1 day

This document specifies the performance requirements for fluxes in solid, liquid and paste forms intended for use with soft solders. NOTE 1 ISO 9454‑1 specifies the requirements for labelling and packaging as well as the coding system for the classification of the fluxes. NOTE 2 Some of the fluxes intended for inert gas and vapour phase soldering may not pass some of the criteria in Tables 1 and 2. Requirements for these fluxes are agreed between the purchaser and the supplier.

    • sale 15% off
    • Standard
      7 pages
      French language
    • sale 15% off
    • Standard
      6 pages
      English language
    • sale 15% off
    • Draft
      6 pages
      English language

This document specifies a distillation method for the determination of the ammonia content of solid, paste or liquid fluxes. The method is applicable to fluxes of class 311 and 321 only, as defined in ISO 9454‑1.

    • sale 15% off
    • Standard
      6 pages
      French language
    • sale 15% off
    • Draft
      6 pages
      English language
    • sale 15% off
    • Standard
      6 pages
      English language

This document specifies requirements for the qualification of welding operators for friction stir welding
(FSW) of aluminium. In this document, the term “aluminium” refers to aluminium and its alloys.
This document does not apply to “operators” as defined in ISO 25239-1.
This document does not apply to friction stir spot welding which is covered by the ISO 18785 series.

    • sale 10% off
    • Standard
      21 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      17 pages
      English language
    • e-Library read for
      1 day

This document specifies the preparation of butt weld test pieces and specimens.
The test pieces and specimens are used to determine the strength and impact properties of welded
joints when testing welding consumables with single-run and two-run techniques.
This document is applicable to welding consumables for arc welding of steel.
This document is not suitable for electro-slag or electro-gas welding.

    • sale 10% off
    • Standard
      14 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      11 pages
      English language
    • e-Library read for
      1 day

This document specifies design requirements for friction stir weld joints.
In this document, the term “aluminium” refers to aluminium and its alloys.
This document does not apply to friction stir spot welding which is covered by the ISO 18785 series.

    • sale 10% off
    • Standard
      14 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      10 pages
      English language
    • e-Library read for
      1 day

This document defines terms related to friction stir welding.
In this document, the term “aluminium” refers to aluminium and its alloys.

    • sale 10% off
    • Standard
      23 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      21 pages
      English language
    • e-Library read for
      1 day

This document specifies requirements for classification of wire electrodes and weld deposits in the
as-welded condition and in the post-weld heat-treated condition for gas shielded metal arc welding of
non alloy and fine grain steels with a minimum yield strength of up to 500 MPa or a minimum tensile
strength of up to 570 MPa. One wire electrode can be tested and classified with different shielding gases.
This document constitutes a combined specification providing classification utilizing a...
view more

    • sale 10% off
    • Standard
      22 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      20 pages
      English language
    • e-Library read for
      1 day

This document specifies requirements for the classification of solid wire electrodes, solid wires and
rods for fusion welding of titanium and titanium alloys. The classification is based on their chemical
composition.
The compositions of solid wire electrodes for metal inert gas (MIG) welding are the same as solid wire
electrodes, solid wires and rods for tungsten inert gas (TIG) arc welding, plasma arc welding, laser
beam welding, and other fusion welding processes.

    • sale 10% off
    • Standard
      20 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      17 pages
      English language
    • e-Library read for
      1 day

This document specifies a method for determining the capability of a manufacturer to use the friction
stir welding (FSW) process for the production of products of the specified quality. It specifies quality
requirements, but does not assign those requirements to any specific product group.
In this document, the term “aluminium” refers to aluminium and its alloys.
This document does not apply to friction stir spot welding which is covered by the ISO 18785 series.

    • sale 10% off
    • Standard
      20 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      17 pages
      English language
    • e-Library read for
      1 day

This document specifies the preparation of test pieces and specimens for all-weld metal tests in steel,
nickel and nickel alloys.
The test pieces and specimens are used to determine the mechanical properties of all-weld metal where
required by consumable classification standards or for other purposes, in arc welding of steel, nickel
and nickel alloys.
This document is not applicable to single- or two-run welding or fillet welding. For these cases,
ISO 15792-2 and ISO 15792-3 apply.

    • sale 10% off
    • Standard
      12 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      10 pages
      English language
    • e-Library read for
      1 day

This document specifies the requirements for the specification and qualification of welding procedures
for the friction stir welding (FSW) of aluminium.
In this document, the term “aluminium” refers to aluminium and its alloys.
This document does not apply to friction stir spot welding which is covered by the ISO 18785 series.
NOTE Service requirements, materials or manufacturing conditions can require more comprehensive
testing than is specified in this document.

    • sale 10% off
    • Standard
      30 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      29 pages
      English language
    • e-Library read for
      1 day

This document specifies requirements for the classification of covered electrodes and deposited metal
in the as-welded condition and in the post-weld heat-treated condition for manual metal arc welding of
non-alloy and fine grain steels with a minimum yield strength of up to 500 MPa or a minimum tensile
strength of up to 570 MPa.
This document is a combined specification providing for classification utilizing a system based on the
yield strength and the average impact energy of 47 J of all-...
view more

    • sale 10% off
    • Standard
      43 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      36 pages
      English language
    • e-Library read for
      1 day

This document specifies the procedure to be used for deposition of a weld metal pad for chemical
analysis.
This document applies to deposition of a weld metal pad by use of covered electrodes, wire electrodes
for gas shielded metal arc welding, tubular cored electrodes for gas shielded metal arc welding and for
non-gas shielded metal arc welding, solid rods and tubular cored rods for gas tungsten arc welding, and
wire-flux and strip-flux combinations for submerged arc welding or electroslag...
view more

    • sale 10% off
    • Standard
      12 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      9 pages
      English language
    • e-Library read for
      1 day

This document specifies a qualitative method for assessing the aggressiveness of a flux towards copper. The test is applicable to all fluxes of type 1 as defined in ISO 9454‑1.

    • sale 15% off
    • Standard
      4 pages
      English language
    • sale 15% off
    • Standard
      5 pages
      French language
    • sale 15% off
    • Draft
      4 pages
      English language