SIST EN ISO 6847:2020
(Main)Welding consumables - Deposition of a weld metal pad for chemical analysis (ISO 6847:2020)
Welding consumables - Deposition of a weld metal pad for chemical analysis (ISO 6847:2020)
This document specifies the procedure to be used for deposition of a weld metal pad for chemical
analysis.
This document applies to deposition of a weld metal pad by use of covered electrodes, wire electrodes
for gas shielded metal arc welding, tubular cored electrodes for gas shielded metal arc welding and for
non-gas shielded metal arc welding, solid rods and tubular cored rods for gas tungsten arc welding, and
wire-flux and strip-flux combinations for submerged arc welding or electroslag welding and cladding.
This document is applicable to welding consumables for non-alloy and fine grain steels, high strength
steels, creep-resisting steels, stainless and heat-resisting steels, nickel and nickel alloys, and copper
and copper alloys.
Schweißzusätze - Auftragung von Schweißgut zur Bestimmung der chemischen Zusammensetzung (ISO 6847:2020)
Dieses Dokument legt das Verfahren zum Auftragen des Schweißgutes zum Ermitteln der chemischen Zusammensetzung fest.
Dieses Dokument gilt für die Herstellung eines Schweißgutblocks durch umhüllte Stabelektroden, Drahtelektroden zum Metall-Schutzgasschweißen, Fülldrahtelektroden zum Metall-Schutzgasschweißen und für selbstschützendes Metall-Lichtbogenschweißen, Massiv- und Füllstäbe für Wolfram-Schutzgasschweißen und Draht/Band-Pulver-Kombinationen für Unterpulverschweißen oder Elektroschlackeschweißen und Plattieren.
Dieses Dokument gilt für Schweißzusätze von unlegierten Stählen, Feinkornstählen, hochfesten Stählen, warmfesten Stählen, nichtrostenden und hitzebeständigen Stählen, Nickel und Nickellegierungen sowie Kupfer und Kupferlegierungen.
Produits consommables pour le soudage - Exécution d'un dépôt de métal fondu pour l'analyse chimique (ISO 6847:2020)
Le présent document spécifie le mode opératoire à utiliser pour réaliser un dépôt de soudure pour l'analyse chimique.
Le présent document est applicable à l'exécution d'un dépôt de métal fondu en utilisant des électrodes enrobées, des fils-électrodes pour le soudage à l'arc sous protection gazeuse, des fils fourrés pour le soudage à l'arc avec et sans protection gazeuse, des baguettes pleines et fourrées pour le soudage à l'arc avec électrode de tungstène, ainsi que des couples fils-flux et feuillard-flux pour le soudage à l'arc sous flux et le soudage sous laitier et le rechargement.
Le présent document est également applicable aux produits consommables pour le soudage des aciers non alliés et à grains fins, des aciers à haute limite d'élasticité, des aciers résistant au fluage, des aciers inoxydables et réfractaires, du nickel et des alliages de nickel, du cuivre et des alliages de cuivre.
Dodajni in pomožni materiali za varjenje - Izdelava čistih varov za kemijsko analizo (ISO 6847:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 6847:2020
01-november-2020
Nadomešča:
SIST EN ISO 6847:2013
Dodajni in pomožni materiali za varjenje - Izdelava čistih varov za kemijsko analizo
(ISO 6847:2020)
Welding consumables - Deposition of a weld metal pad for chemical analysis (ISO
6847:2020)
Schweißzusätze - Auftragung von Schweißgut zur Bestimmung der chemischen
Zusammensetzung (ISO 6847:2020)
Produits consommables pour le soudage - Exécution d'un dépôt de métal fondu pour
l'analyse chimique (ISO 6847:2020)
Ta slovenski standard je istoveten z: EN ISO 6847:2020
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
SIST EN ISO 6847:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 6847:2020
---------------------- Page: 2 ----------------------
SIST EN ISO 6847:2020
EN ISO 6847
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2020
EUROPÄISCHE NORM
ICS 25.160.20 Supersedes EN ISO 6847:2013
English Version
Welding consumables - Deposition of a weld metal pad for
chemical analysis (ISO 6847:2020)
Produits consommables pour le soudage - Exécution Schweißzusätze - Auftragung von Schweißgut zur
d'un dépôt de métal fondu pour l'analyse chimique Bestimmung der chemischen Zusammensetzung (ISO
(ISO 6847:2020) 6847:2020)
This European Standard was approved by CEN on 20 August 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6847:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 6847:2020
EN ISO 6847:2020 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 6847:2020
EN ISO 6847:2020 (E)
European foreword
This document (EN ISO 6847:2020) has been prepared by Technical Committee ISO/TC IIW
"International Institute of Welding" in collaboration with Technical Committee CEN/TC 121 “Welding
and allied processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2021, and conflicting national standards shall
be withdrawn at the latest by March 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 6847:2013.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 6847:2020 has been approved by CEN as EN ISO 6847:2020 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 6847:2020
---------------------- Page: 6 ----------------------
SIST EN ISO 6847:2020
INTERNATIONAL ISO
STANDARD 6847
Fourth edition
2020-08
Welding consumables — Deposition
of a weld metal pad for chemical
analysis
Produits consommables pour le soudage — Exécution d'un dépôt de
métal fondu pour l'analyse chimique
Reference number
ISO 6847:2020(E)
©
ISO 2020
---------------------- Page: 7 ----------------------
SIST EN ISO 6847:2020
ISO 6847:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 6847:2020
ISO 6847:2020(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Base metal . 1
4.1 Type . 1
4.2 Dimensions . 2
4.3 Surface condition . 2
5 Method for preparing the weld metal pad . 2
5.1 Drying of the welding consumables . 2
5.2 Welding position . 2
5.3 Type of current . 2
5.4 Welding conditions . 2
5.5 Welding method . 3
5.5.1 General. 3
5.5.2 Covered electrodes . 3
5.5.3 Solid wires and rods, strips, and tubular cored wires and rods . 4
6 Weld metal pad size . 4
7 Sampling . 4
© ISO 2020 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 6847:2020
ISO 6847:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval cri
...
SLOVENSKI STANDARD
oSIST prEN ISO 6847:2019
01-december-2019
[Not translated]
Welding consumables - Deposition of a weld metal pad for chemical analysis (ISO/DIS
6847:2019)
Schweißzusätze - Auftragung von Schweißgut zur Bestimmung der chemischen
Zusammensetzung (ISO/DIS 6847:2019)
Produits consommables pour le soudage - Exécution d'un dépôt de métal fondu pour
l'analyse chimique (ISO/DIS 6847:2019)
Ta slovenski standard je istoveten z: prEN ISO 6847
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
oSIST prEN ISO 6847:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 6847:2019
---------------------- Page: 2 ----------------------
oSIST prEN ISO 6847:2019
DRAFT INTERNATIONAL STANDARD
ISO/DIS 6847
IIW Secretariat: ISO secretariat
Voting begins on: Voting terminates on:
2019-10-23 2020-01-15
Welding consumables — Deposition of a weld metal pad
for chemical analysis
Produits consommables pour le soudage — Exécution d'un dépôt de métal fondu pour l'analyse chimique
ICS: 25.160.20
Member bodies are requested to consult relevant national interests in ISO/TC
44/SC 3 before casting their ballot to the e-Balloting application.
This document is circulated as received from the committee secretariat.
ISO/CEN PARALLEL PROCESSING
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
This draft International Standard is submitted to all ISO member bodies for
NOT BE REFERRED TO AS AN INTERNATIONAL
voting, as a standard prepared by an international standardizing body in
STANDARD UNTIL PUBLISHED AS SUCH.
accordance with Council Resolution 42/1999. The proposer, the International
IN ADDITION TO THEIR EVALUATION AS
Institute of Welding (IIW), has been recognized by the ISO Council as an
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
international standardizing body for the purpose of Council Resolution
USER PURPOSES, DRAFT INTERNATIONAL
42/1999.
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 6847:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019
---------------------- Page: 3 ----------------------
oSIST prEN ISO 6847:2019
ISO/DIS 6847:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 6847:2019
ISO/DIS 6847:2019(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Base metal . 1
4.1 Type . 1
4.2 Dimensions . 1
4.3 Surface condition . 1
5 Method for preparing the weld metal pad . 2
5.1 Drying of the welding consumables . 2
5.2 Welding position . 2
5.3 Type of current . 2
5.4 Welding conditions . 2
5.5 Welding method . 2
5.5.1 General. 2
5.5.2 Covered electrodes . 3
5.5.3 Solid wires and rods, strips, and tubular cored wires and rods . 3
6 Weld metal pad size . 4
7 Sampling . 4
© ISO 2019 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 6847:2019
ISO/DIS 6847:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso
.org/iso/fore
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.