SIST EN 3219:2020

Aerospace series - Heat resisting nickel base alloy (Ni-P100HT) - Cold worked and softened - Bar and wire for continuous forging or extrusion for fasteners - 3 mm ≤ D ≤ 30 mm

This standard specifies the requirements relating to:Heat resisting nickel base alloy (NI-P100HT)Cold worked and softenedBar and wire for continuous forging or extrusion for fasteners3 mm ≤ D ≤ 30 mmfor aerospace applications.

Luft- und Raumfahrt - Hochwarmfeste Nickellegierung (Ni-P100HT) - Kaltverfestigt und abgeschreckt - Stangen und Drähte zum kontinuierlichen Verformen oder Strangpressen für Verbindungselemente - 3 mm ≤ D ≤ 30 mm

Dieses Dokument legt die Anforderungen an:
Hochwarmfeste Nickellegierung (NI P100HT)
Kaltverfestigt und weichgeglüht
Stange und Draht zum kontinuierlichen Verformen oder Strangpressen für Verbindungselemente
3 mm ≤ D ≤ 30 mm
für Anwendungen in der Luft  und Raumfahrt fest.

Série aérospatiale - Alliage résistant à chaud base nickel (Ni-P100HT) - Écroui et adouci - Barre et fil pour le forgeage ou l'extrusion en continu pour fixations - 3 mm ≤ D ≤ 30 mm

Le présent document spécifie les exigences relatives à :
Alliage résistant à chaud base nickel (NI-P100HT) Écroui et adouci Barre et fil pour le forgeage ou l’extrusion en continu pour fixations 3 mm ≤ D ≤ 30 mm
pour applications aérospatiales.

Aeronavtika - Toplotno odporne zlitine na nikljevi osnovi (Ni-P100HT) - Hladno obdelana in popuščana - Palice in žice za kontinuirno kovanje ali iztiskanje vezalnih elementov - 3 mm ≤ D ≤ 30 mm

Ta standard določa zahteve, ki se navezujejo na: toplotno odporne zlitine na nikljevi osnovi (NI-P100HT), hladno obdelana in popuščana, palice in žice za kontinuirano kovanje ali iztiskanje vezalnih elementov 3 mm ≤ D ≤ 30 mm za uporabo v aeronavtiki.

General Information

• Status: Published
• Publication Date: 10-Feb-2020
• ICS: 49.025.99 - Other materials
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 23-Jan-2020
• Due Date: 29-Mar-2020
• Completion Date: 11-Feb-2020
• Ref Project: EN 3219:2020 - Aerospace series - Heat resisting nickel base alloy (NI-P100HT) - Cold worked and softened - Bar and wire for continuous forging or extrusion for fasteners - 3 mm ≤ D ≤ 30 mm

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 3219:2020
01-marec-2020
Aeronavtika - Toplotno odporne zlitine na nikljevi osnovi (Ni-P100HT) - Hladno
obdelana in popuščana - Palice in žice za kontinuirno kovanje ali iztiskanje
vezalnih elementov - 3 mm ≤ D ≤ 30 mm
Aerospace series - Heat resisting nickel base alloy (Ni-P100HT) - Cold worked and
softened - Bar and wire for continuous forging or extrusion for fasteners - 3 mm ≤ D ≤ 30
mm
Luft- und Raumfahrt - Hochwarmfeste Nickellegierung (Ni-P100HT) - Kaltverfestigt und
abgeschreckt - Stangen und Drähte zum kontinuierlichen Verformen oder Strangpressen
für Verbindungselemente - 3 mm ≤ D ≤ 30 mm
Série aérospatiale - Alliage résistant à chaud base nickel (Ni-P100HT) - Écroui et adouci
- Barre et fil pour le forgeage ou l'extrusion en continu pour fixations - 3 mm ≤ D ≤ 30 mm
Ta slovenski standard je istoveten z: EN 3219:2020
ICS:
49.025.99 Drugi materiali Other materials
SIST EN 3219:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 3219:2020

---------------------- Page: 2 ----------------------
SIST EN 3219:2020


EN 3219
EUROPEAN STANDARD

NORME EUROPÉENNE

January 2020
EUROPÄISCHE NORM
ICS 49.025.99
English Version

Aerospace series - Heat resisting nickel base alloy (NI-
P100HT) - Cold worked and softened - Bar and wire for
continuous forging or extrusion for fasteners - 3 mm ≤ D ≤
30 mm
Série aérospatiale - Alliage résistant à chaud base Luft- und Raumfahrt - Hochwarmfeste Nickellegierung
nickel (Ni-P100HT) - Écroui et adouci - Barre et fil pour (Ni-P100HT) - Kaltverfestigt und abgeschreckt -
le forgeage ou l'extrusion en continu pour fixations - 3 Stangen und Drähte zum kontinuierlichen Verformen
mm ≤ D ≤ 30 mm oder Strangpressen für Verbindungselemente - 3 mm ≤
D ≤ 30 mm
This European Standard was approved by CEN on 14 January 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 3219:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 3219:2020
EN 3219:2020 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Requirements . 5
Bibliography . 8

2

---------------------- Page: 4 ----------------------
SIST EN 3219:2020
EN 3219:2020 (E)
European foreword
This document (EN 3219:2020) has been prepared by the Aerospace and Defence Industries Association of
Europe — Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of ASD,
prior to its presentation to CEN.
This document shall be given the status of a national standard, either by publication of an identical text or by
endorsement, at the latest by July 2020, and conflicting national standards shall be withdrawn at the latest by
July 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North Macedo
...