iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F2030-08

(Specification)

Standard Specification for Paintball Cylinder Burst Disk Assemblies

Standard Specification for Paintball Cylinder Burst Disk Assemblies

ABSTRACT
This specification covers cylinder burst disk assemblies for paintball marker propellant sources their application and installation requirements. The materials and processes used to manufacture the burst disk assembly shall result in items with mechanical strength sufficient to pass the applicable burst pressure tests. Materials used shall be corrosion resistant, chemically compatible with the propellant used, and shall not promote galvanic action. The burst disk assembly and related port features shall be free of burrs and sharp edges. Burst disk assemblies intended for use with the specified service pressure shall meet the prescribed rupture pressure and temperature conditions. The relief hole in the burst disk assembly shall provide for flow to adequately vent the cylinder as specified. The rupture disk and seal shall be permanently retained on the plug to provide proper alignment and assembly. The burst disk assembly and port shall conform to the physical envelope as described in the illustrations given. The burst disk shall be marked with manufacturer code and rated burst pressure. Prior to installation the mating port and the burst disk assembly shall be inspected to confirm compliance with physical envelope requirements, cleanliness, and general suitability for use.
SCOPE
1.1 This specification covers burst disk assemblies for paintball marker propellant sources their application and installation requirements.
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Oct-2008
ICS
97.220.40 - Outdoor and water sports equipment
Technical Committee
F08 - Sports Equipment, Playing Surfaces, and Facilities
Drafting Committee
F08.24 - Paintball and Equipment
Current Stage
Ref Project

Relations

Replaces
ASTM F2030-00 - Standard Specification for Paintball Cylinder Burst Disk Assemblies
Effective Date
01-Nov-2008
Replaced By
ASTM F2030-11 - Standard Specification for Paintball Cylinder Burst Disk Assemblies
Effective Date
01-Mar-2011
Referred By
ASTM F2653-16(2020) - Standard Specification for Paintball Valve Male Threaded Connection for Use with Approved Cylinders
Effective Date
01-Nov-2008
Referred By
ASTM F590-22 - Standard Consumer Safety Specification for Non-Powder Gun Projectiles and Propellants
Effective Date
01-Nov-2008
Referred By
ASTM F1777-19(2023) - Standard Practice for Paintball Game Site Operation
Effective Date
01-Nov-2008
Referred By
ASTM F2748-19 - Standard Specification for Airsoft Guns
Effective Date
01-Nov-2008
Referred By
ASTM F3100-15(2023) - Standard Practice for Low Impact Paintball Field Operation
Effective Date
01-Nov-2008
Referred By
ASTM F2773-13(2021) - Standard Practice for Transfilling Compressed Air or Nitrogen and Safe Handling of Small Paintball Cylinders
Effective Date
01-Nov-2008
Referred By
ASTM F2856-12(2020) - Standard Practice for Transfilling and Safe Handling of Small CO<inf>2</inf> Cylinders for Use in Paintball
Effective Date
01-Nov-2008

Buy Standard

ASTM F2030-08 - Standard Specification for Paintball Cylinder Burst Disk AssembliesASTM F2030-08 - Standard Specification for Paintball Cylinder Burst Disk Assemblies
PreviousNext
Technical specification
ASTM F2030-08 - Standard Specification for Paintball Cylinder Burst Disk Assemblies
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM F2030-08 - Standard Specification for Paintball Cylinder Burst Disk AssembliesREDLINE ASTM F2030-08 - Standard Specification for Paintball Cylinder Burst Disk Assemblies
PreviousNext
Technical specification
REDLINE ASTM F2030-08 - Standard Specification for Paintball Cylinder Burst Disk Assemblies
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM F2030-08 - Standard Specification for Paintball Cylinder Burst Disk AssembliesREDLINE ASTM F2030-08 - Standard Specification for Paintball Cylinder Burst Disk Assemblies
PreviousNext
Technical specification
REDLINE ASTM F2030-08 - Standard Specification for Paintball Cylinder Burst Disk Assemblies
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: F2030 – 08
Standard Specification for
1
Paintball Cylinder Burst Disk Assemblies
This standard is issued under the fixed designation F2030; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.2 Abbreviations:
3.2.1 psi—pounds per square inch
1.1 This specification covers burst disk assemblies for
paintball marker propellant sources their application and in-
4. Materials and Manufacture
stallation requirements.
4.1 The materials and processes used to manufacture the
1.2 The values stated in SI units are to be regarded as
burst disk assembly shall result in items with mechanical
standard. The values given in parentheses are for information
strength sufficient to pass the applicable burst pressure tests.
only.
Materials used shall be corrosion resistant, chemically compat-
1.3 This standard does not purport to address all of the
ible with the propellant used, and shall not promote galvanic
safety concerns, if any, associated with its use. It is the
action. Burst disks shall be manufactured and tested in accor-
responsibility of the user of this standard to establish appro-
dance with DOT 49 CFR and CGA S-1.1.
priate safety and health practices and determine the applica-
4.2 The burst disk assembly and related port features shall
bility of regulatory limitations prior to use.
be free of burrs and sharp edges.
2. Referenced Documents
5. Performance
2
2.1 Code of Federal Regulations:
5.1 Burst disk must rupture between 90 and 100 % of test
DOT 49 CFR
3
pressure as noted in Table 1.
2.2 CGA Standard:
5.2 Burst disk assembly must contain a minimum of two
CGA S-1.1 Pressure Relief Device Standards-Part
relief holes positioned 180° apart.
1-Cylinders for Compressed Gases
5.3 Relief holes must be oriented to reduce the likelihood of
CGATB-13 CorrectAssemblies and Installation of Rupture
thrust resulting in cylinder spin.
Disk and Fusible Plug Type Pressure Relief Devices
5.4 The relief hole in the burst disk assembly shall provide
3. Terminology for flow to adequately vent the cylinder as specified in CGA
S-1.1.
3.1 Definitions of Terms Specific to This Standard:
5.5 The burst disk and seal shall be affixed on the plug to
3.1.1 Burst Disk Assembly is sometimes known as a Rup-
provide proper alignment and assembly.
ture Disk Assembly.
5.6 The burst disk assembly will be of a single use design
3.1.2 burst disk port, n—port into which a burst disk
(non user resetable or rebuildable). Therefore, if activated, this
assembly is installed.
will require the replacement of the entire burst disk assembly.
3.1.3 service pressure, n—operating pressure as indicated
by markings placed on cylinder at time of manufacture.
6. Marking
5
3.1.4 test pressure, n— ⁄3 of cylinder’s service pressure.
6.1 The burst disk assembly shall be marked with its
maximum rated burst pressure. This shall be done in accor-
1
This specification is under the jurisdiction ofASTM Committee F08 on Sports dance with Table 1.
Equipment and Facilities and is the direct responsibility of Subcommittee F08.24 on
6.2 Themarkingsontheburstdiskassemblyshallbeatleast
Paintball and Equipment.
10 point type and must be marked so as to be clearly visible as
Curren
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:F2030–00 Designation: F 2030 – 08
Standard Specification for
1
Paintball Cylinder Burst Disk Assemblies
This standard is issued under the fixed designation F 2030; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers burst disk assemblies for paintball marker propellant sources their application and installation
requirements.
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 Code of Federal Regulations:
DOT 49 CFR 1734d DOT 49 CFR
3
2.2 CGA Standard:
CGAS-1-1 CGA S-1.1 Pressure Relief Device Standards-Part 1-Cylinders for Compressed Gases
CGA TB-13 Correct Assemblies and Installation of Rupture Disk and Fusible Plug Type Pressure Relief Devices
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 Burst Disk Assembly is sometimes known as a Rupture Disk Assembly.
3.1.2 burst disk port, n—port into which a burst disk assembly is installed.
3.1.3 service pressure, n—operating pressure as indicated by markings placed on cylinder at time of manufacture.
5
3.1.4 test pressure, n— ⁄3 of cylinder’s service pressure.
3.2 Abbreviations:
3.2.1 psi—pounds per square inch
4. Materials and Manufacture
3.1The4.1 The materials and processes used to manufacture the burst disk assembly shall result in items with mechanical
strength sufficient to pass the applicable burst pressure tests. Materials used shall be corrosion resistant, chemically compatible
withthepropellantused,andshallnotpromotegalvanicaction.RuptureBurstdisksshallbemanufacturedandtestedinaccordance
with DOT 49 CFR 1734d and CGA S-1-1S-1.1.
3.2The4.2 The burst disk assembly and related port features shall be free of burrs and sharp edges.
4.5. Performance
4.1Burst disk assemblies intended for use with a service pressure of 12 410 kPa (1800 psi) shall rupture at not less than 18 615
kPa (2700 psi) and no more than 20 684 kPa (3000 psi) at a temperature of 71.1°C (160°F). At a temperature of 15.6°C (60°F)
the same burst disk shall rupture at not less than 19 822 kPa (2875 psi) and no more than 21 890 kPa (3175 psi).
4.2The relief hole in the burst disk assembly shall provide for flow to adequately vent the cylinder as specified in CGA S-1-1
5.1 Burst disk must rupture between 90 and 100 % of test pressure as noted in Table 1.
4.3The rupture disk and seal shall be permanently retained on the plug to provide proper alignment and assembly.
1
This specification is under the jurisdiction of ASTM Committee F08 on Sports Equipment and Facilities and is the direct responsibility of Subcommittee F08.24 on
Paintball and Equipment.
Current edition approved June 10, 2000. Published August 2000.
Current edition approved Nov. 1, 2008. Published November 2008. Originally approved in 2000. Last previous edition approved in 2000 as F 2030 – 00.
2
Code of Federal Regulations, available from U.S. Government Printing Office, Washington, DC 20402.
3
Available from Compressed Gas Assoc., Inc., 1725 Jefferson Davis Highway, Suite 1004, Arlington, VA 22202–4102.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F2030–08
TABLE 1 Burst Disk Burst Pressure and Markings
Service Pressure 1800 psi 3000 psi 4500 or 5000 psi
Minimum Burst Disk Burst Pressure @ SAT 2700 psi 4500 psi 6750 psi
Maximum Burst Disk Burst Pressure @ SAT 3000 psi 5000 psi 7500 psi
Burst Disk Marking (Fig. 1) 3K 5K 7.5K
Burst Disk Port Marking 3K ONLY 5K ONLY 7.5K ONLY
Burst Disk Assembly Thread Specification 3/8-24UNF-2A 3/8-24UNF-2A 3/8-24UNF-2A
Burst Disk Port Thread Specification 3/8-24UNF-2B 3/8-24UNF-2B 3/8-24UNF-2B
5.
5.2 Burst disk assembly must contain a minimum of two relief holes positioned 180° apart.
5.3 Relief holes must be oriented to reduce the likelihood of thrust resulting in cylinder spin.
5.4 The relief hole in the burst disk
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:F2030–00 Designation: F 2030 – 08
Standard Specification for
1
Paintball Cylinder Burst Disk Assemblies
This standard is issued under the fixed designation F 2030; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers burst disk assemblies for paintball marker propellant sources their application and installation
requirements.
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 Code of Federal Regulations:
DOT 49 CFR 1734d DOT 49 CFR
3
2.2 CGA Standard:
CGAS-1-1 CGA S-1.1 Pressure Relief Device Standards-Part 1-Cylinders for Compressed Gases
CGA TB-13 Correct Assemblies and Installation of Rupture Disk and Fusible Plug Type Pressure Relief Devices
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 Burst Disk Assembly is sometimes known as a Rupture Disk Assembly.
3.1.2 burst disk port, n—port into which a burst disk assembly is installed.
3.1.3 service pressure, n—operating pressure as indicated by markings placed on cylinder at time of manufacture.
5
3.1.4 test pressure, n— ⁄3 of cylinder’s service pressure.
3.2 Abbreviations:
3.2.1 psi—pounds per square inch
4. Materials and Manufacture
3.1The4.1 The materials and processes used to manufacture the burst disk assembly shall result in items with mechanical
strength sufficient to pass the applicable burst pressure tests. Materials used shall be corrosion resistant, chemically compatible
withthepropellantused,andshallnotpromotegalvanicaction.RuptureBurstdisksshallbemanufacturedandtestedinaccordance
with DOT 49 CFR 1734d and CGA S-1-1S-1.1.
3.2The4.2 The burst disk assembly and related port features shall be free of burrs and sharp edges.
4.5. Performance
4.1Burst disk assemblies intended for use with a service pressure of 12 410 kPa (1800 psi) shall rupture at not less than 18 615
kPa (2700 psi) and no more than 20 684 kPa (3000 psi) at a temperature of 71.1°C (160°F). At a temperature of 15.6°C (60°F)
the same burst disk shall rupture at not less than 19 822 kPa (2875 psi) and no more than 21 890 kPa (3175 psi).
4.2The relief hole in the burst disk assembly shall provide for flow to adequately vent the cylinder as specified in CGA S-1-1
5.1 Burst disk must rupture between 90 and 100 % of test pressure as noted in Table 1.
4.3The rupture disk and seal shall be permanently retained on the plug to provide proper alignment and assembly.
1
This specification is under the jurisdiction of ASTM Committee F08 on Sports Equipment and Facilities and is the direct responsibility of Subcommittee F08.24 on
Paintball and Equipment.
Current edition approved June 10, 2000. Published August 2000.
Current edition approved Nov. 1, 2008. Published November 2008. Originally approved in 2000. Last previous edition approved in 2000 as F 2030 – 00.
2
Code of Federal Regulations, available from U.S. Government Printing Office, Washington, DC 20402.
3
Available from Compressed Gas Assoc., Inc., 1725 Jefferson Davis Highway, Suite 1004, Arlington, VA 22202–4102.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F2030–08
TABLE 1 Burst Disk Burst Pressure and Markings
Service Pressure 1800 psi 3000 psi 4500 or 5000 psi
Minimum Burst Disk Burst Pressure @ SAT 2700 psi 4500 psi 6750 psi
Maximum Burst Disk Burst Pressure @ SAT 3000 psi 5000 psi 7500 psi
Burst Disk Marking (Fig. 1) 3K 5K 7.5K
Burst Disk Port Marking 3K ONLY 5K ONLY 7.5K ONLY
Burst Disk Assembly Thread Specification 3/8-24UNF-2A 3/8-24UNF-2A 3/8-24UNF-2A
Burst Disk Port Thread Specification 3/8-24UNF-2B 3/8-24UNF-2B 3/8-24UNF-2B
5.
5.2 Burst disk assembly must contain a minimum of two relief holes positioned 180° apart.
5.3 Relief holes must be oriented to reduce the likelihood of thrust resulting in cylinder spin.
5.4 The relief hole in the burst disk
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F3545-23(Test Method)
Standard Test Method for Static Loading of Treestands, Climbing Sticks, and Tripod or Tower Stands

SCOPE
1.1 This test method covers procedures for static loading of various components of treestands, climbing sticks, and tripod/tower stands that are used for hunting, photographing, or general observation. This test method includes the corresponding factors of safety that each component should be evaluated to as shown in Table 1.  
1.2 The values stated are in inch-pound units and are to be regarded as the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM F2123-23(Practice)
Standard Practice for Treestand Instructions

SIGNIFICANCE AND USE
5.1 This practice is provided to develop and maintain uniformity in practices for instructions for treestands, climbing sticks (continuous and sectional), tripods, and towers, particularly with regard to quality assurance and safety.  
5.2 It is emphasized that the use of these practices will not alter the validity of data determined with specific tests related to other standards.
SCOPE
1.1 This practice provides guidance for providing user instructions for treestands.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM F910-04(2023)(Specification)
Standard Specification for Face Guards for Youth Baseball

ABSTRACT
This specification covers protective face guards designed to be attached to a pre-existing helmet for youth baseball. General requirements for protective face guards shall include mechanical strength, durability, flexibility, finish, padding, attachment system, and shall not cause skin irritation. The face guard shall undergo velocity and impact testing using apparatus such as headform and mounting, ball propelling device, and gage.
SCOPE
1.1 This specification covers protective face guards for sports such as youth baseball (batters and baserunners).  
1.2 This type of face guard is designed to be attached to a pre-existing helmet.  
1.3 The equipment covered by this specification is intended to reduce hazards of injury to the face, including eyes and mouth, due to impacts from baseballs or softballs.  
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.5 The following precautionary caveat pertains only to the test method portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM F2272-23(Specification)
Standard Specification for Paintball Markers

ABSTRACT
This specification covers the performance requirements and test methods for paintball markers that propel paintballs using energy released from compressed air, compressed gas, or a combination of compressed air and gas. This does not cover non-recreational paintball markers such as those used in law enforcement, scientific, military or theatrical entities. All paintball markers should be supplied with appropriate literature, packaging, finish, design, and disabling device and shipped according to the specified shipping conditions. Under no circumstances should the cocking or pumping mechanism of a paintball marker cause a marker to discharge unintentionally while the marker is being cocked in accordance to instructions. Markers should not accidentally discharge when exposed to jolts strengths within the specified range.
SCOPE
1.1 This specification covers paintball markers, which propel a paintball by means of energy released by compressed air, compressed gas, or other means.  
1.2 Limitations—This specification does not cover non-recreational paintball markers, for example, those used by law enforcement, scientific, military or theatrical entities.  
1.3 The values stated in SI units are to be regarded as the standard; the inch-pound units in parentheses are provided for information only.  
1.4 The following precautionary caveat pertains only to the test method portion, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM F2278-19(2023)(Test Method)
Standard Test Method for Evaluating Paintball Barrier Netting

SIGNIFICANCE AND USE
4.1 This method is performed to evaluate if paintball barrier netting will prevent an intact paintball or shell fragments exceeding 3 by 5 mm (0.118 by 0.197 in.) from passing through the netting.  
4.2 This test method provides accurate results about the current effectiveness of the test specimen when field-tested in an existing installation. Laboratory results are particularly useful for testing the relative effectiveness of multiple test specimens.  
4.3 The results stemming from the use of this test method may be used to evaluate the effectiveness of paintball barrier netting represented by the test specimen for use in delineating “goggles-on” areas found at paintball playing fields.  
4.4 The base procedure outlined below is applicable to “field-testing.” Additional requirements for “laboratory” testing are noted.
SCOPE
1.1 This test method is designed to evaluate paintball barrier netting that may be used to delineate playing fields, chronograph areas, target ranges, and other “goggle-on” areas of an active paintball site. An apparatus is suggested to evaluate paintball barrier netting in a laboratory. On site testing does not require such an apparatus.  
1.2 This standard is designed to be used in conjunction with Guide F2184.  
1.3 The values stated in SI units are to be regarded as the standard; the inch-pound units in parentheses are provided for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F2271-11(2023)(Specification)
Standard Specification for Paintball Marker Barrel Blocking Devices

SCOPE
1.1 This specification covers paintball barrel blocking devices that may be inserted or otherwise function to prevent a paintball from leaving the muzzle or the confines of the barrel blocking device intact.  
1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are provided for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM F2801-19(2023)(Practice)
Standard Practice for Paintball Player Safety Briefing

SIGNIFICANCE AND USE
4.1 Specific safety rules and procedures are important in order to minimize the risk of injury to persons in the general area of paintball markers and gas propellant storage vessels.
SCOPE
1.1 This standard is intended to satisfy the demand for basic safety information, which should be understood by each paintball game participant, prior to the start of the player’s first game on the day of play.  
1.2 The information specifies rules of personal conduct, which might affect the safety of persons who are in close proximity to a paintball marker or a propellant gas storage vessel.  
1.3 The information includes procedures to be followed by every person who is in, or near, an area where paintballs are being shot, and to the use of safety equipment related to paintball games or paintball target shooting activities. These procedures are to be followed any time a paintball marker is being handled.  
1.4 This standard is intended to be a useful tool for paintball game organizers, but it is not intended to eliminate the need for proper field operation conforming to Specification F1777.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM F1890-23(Test Method)
Standard Test Method for Measuring Softball and Baseball Bat Performance Factor

SIGNIFICANCE AND USE
4.1 These test methods offer a laboratory means to quantitatively compare the performance of softball and baseball bats.
SCOPE
1.1 A method for determining bat performance by measuring the bat-ball coefficient of restitution (BBCOR) and deriving the bat performance factor (BPF). It is applicable to softball and baseball bats of any construction or material. The method provides a quantitative measure of bat dynamic performance that may be used for comparison purposes.  
1.2 The BBCOR and BPF are calculated from measurements taken in the laboratory on test equipment meeting the requirements defined in this method.  
1.3 Bat performance is found in this standard assuming the bat is pivoted.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM F1163-23(Specification)
Standard Specification for Protective Headgear Used in Horse Sports and Horseback Riding

ABSTRACT
This specification provides a description of a test method for protective headgear used in horse sports and horseback riding that will measure the ability of the headgear to reduce head acceleration when impacting objects of various shapes. Materials covered by this specification include the pair of appropriate size headform and helmet and the anvils for the impacts tests, which consist of the flat anvil and the equestrian hazard anvil. The helmet shall be conditioned in the following environments: ambient, low temperature, high temperature, and water immersion, and shall be impacted at each of four sites centered on or anywhere above the center of the impact line (two sites on the flat anvil and two sites on the equestrian hazard anvil). Dynamic loading and helmet stability tests shall be performed and shall conform to the requirements specified.
SCOPE
1.1 This specification covers minimum performance criteria and describes test methods for protective headgear for use in horse sports and horseback riding.  
1.2 It is not the intention of this specification to bar from consideration materials of improved quality or performance not known at the time of development of this specification.  
1.3 All testing and requirements of this specification shall be in accordance with Test Methods F1446, except where noted herein.  
1.4 The values stated in SI units are to be regarded as the standard.  
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM F2128-22(Test Method)
Standard Test Method for Treestand Repetitive Loading Capability

SIGNIFICANCE AND USE
5.1 This test method is intended for quality assurance and production control purposes with recognition that individual usage will vary considerably. This test method is not intended to be an independent material or product-acceptance test.
SCOPE
1.1 This test method covers the procedures for determining the capability of climbing and ladder treestands, climbing sticks (Sectional and Continuous), and tripods/towers to withstand repeated loading relative to the manufacturer's rated capacity. For actual specification requirements for each subject unit refer to Specification F3249.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off