ASTM D5025-99
(Specification)Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials
Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials
SCOPE
1.1 This specification covers the physical dimensions and characteristics of a laboratory burner to be used as an ignition source for small-scale burning tests on plastic materials. The burner is used with methane, propane or butane supply gases for flame heights of 20 to 125 mm. Note 1-The burner described in this specification is suitable for use in the following ASTM standards: Specification C 509, Methods D229, Test Method D635, Methods D876, Test Method D3014, Method D3713, Method D3801, Test Method D4804, Test Method D4986, Test Method D5048, and Test Method F777. Safety hazards and known limitations on applicability of fire-test-response standards are addressed in the individual methods.
1.2 The values stated in SI units are to be regarded as the standard. Note 2-This specification is referenced in ISO 10093. 20- and 125-mm test flames, calibrated in accordance with Practice D5207 are technically equivalent to ISO 10093 categories of ignition sources designated P/PF2 and P/PF3, respectively.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D 5025 – 99
Standard Specification for
Laboratory Burner Used for Small-Scale Burning Tests on
Plastic Materials
This standard is issued under the fixed designation D 5025; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope* D 3014 Test Method for Flame Height, Time of Burning,
and Loss of Mass of Rigid Thermoset Cellular Plastics in
1.1 This specification covers the physical dimensions and
a Vertical Position
characteristics of a laboratory burner to be used as an ignition
D 3713 Test Method for Measuring Response of Solid
source for small-scale burning tests on plastic materials. The
Plastics to Ignition by a Small Flame
burner is used with methane, propane, or butane supply gases
D 3801 Test Method for Measuring the Comparative Extin-
for flame heights of 20 to 125 mm.
guishing Characteristics of Solid Plastics in a Vertical
NOTE 1—Theburnerdescribedinthisspecificationissuitableforusein
Position
the followingASTM standards: Specification C 509,Test Methods D 229,
D 4804 Test Methods for Determining the Flammability
Test Method D 635, Test Methods D 876, Test Method D 3014, Test
Characteristics of Nonrigid Solid Plastics
Method D 3713,Test Method D 3801,Test Methods D 4804,Test Method
D 4986 Test Method for Horizontal Burning Characteristics
D 4986, Test Method D 5048, and Test Method F 777. Safety hazards and
of Cellular Polymeric Materials
known limitations on applicability of fire-test-response standards are
addressed in the individual test methods.
D 5048 Test Method for Measuring the Comparative Burn-
NOTE 2—This specification is referenced in ISO 10093 as ignition
ing Characteristics and Resistance to Burn-Through of
source P/PF2.
Solid Plastics Using a 125-mm Flame
NOTE 3—This specification is equivalent to IEC 60695-2-4/2 for a
D 5207 Practice for Calibration of 20 and 125-mm Test
500-W flame and IEC 60695-2-4/3 for a 50-W flame.
Flames for Small-Scale Burning Tests on Plastic Materials
E 176 Terminology of Fire Standards
2. Referenced Documents
F 777 Test Method for Resistance of Electrical Wire Insu-
2.1 ASTM Standards:
lation Materials to Flame at 60°
C 509 Specification for Elastomeric Cellular Preformed
2.2 ISO Standards:
Gasket and Sealing Material
ISO 10093 Plastics—Standard Ignition Sources
D 229 Test Methods for Rigid Sheet and Plate Materials
2.3 IEC Standards:
Used for Electrical Insulation
IEC 60695-2-4/2 Fire Hazard Testing—Part 2: Test Meth-
D 635 Test Method for Rate of Burning and/or Extent and
ods. Section 4, Sheet 2: 500W Nominal Premixed Test
Time of Burning of Self-Supporting Plastics in a Horizon-
Flame and Guidance
tal Position
IEC 60695-2-4/3 Fire Hazard Testing—Part 2: Test Meth-
D 876 Test Methods for Nonrigid Vinyl Chloride Polymer
ods. Section 4, Sheet 3: 50W Nominal Premixed Test
Tubing Used for Electrical Insulation
Flame and Guidance
D 883 Terminology Relating to Plastics
D 1600 Terminology of Abbreviated Terms Relating to
3. Terminology
Plastics
3.1 Definitions—For terms relating to plastics, the defini-
tions are in accordance with Terminology D 883, and the
This specification is under the jurisdiction of ASTM Committee D20 on abbreviations are in accordance with Terminology D 1600. For
Plastics and is the direct responsibility of Subcommittee D20.30 on Thermal
terms relating to fire, the definitions are in accordance with
Properties.
Terminology E 176.
Current edition approved April 10, 1999. Published July 1999. Originally
published as D 5025 – 89. Last previous edition D 5025 – 94.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Withdrawn.
Standards volume information, refer to the standard’s Document Summary page on Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
the ASTM website. 4th Floor, New York, NY 10036.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
D5025–99
4. Design 4.1.2 Burner Orifice—The base of the burner shall be
equipped with an orifice of 0.90 6 0.03 mm in diameter and
4.1 The burner shall consist of a barrel that threads onto a
1.60 6 0.05 mm in length.
one-piece base and gas inlet, as
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.