ASTM E927-10(2015)
(Specification)Standard Specification for Solar Simulation for Photovoltaic Testing
Standard Specification for Solar Simulation for Photovoltaic Testing
ABSTRACT
This specification provides the performance requirements and parameters used for classifying both pulsed and steady state solar simulators intended for indoor testing of photovoltaic devices (solar cells or modules), according to their spectral match to a reference spectral irradiance, non-uniformity of spatial irradiance, and temporal instability of irradiance. The classification of a solar simulator is based on the size of the test plane, and does not provide any information about electrical measurement errors that are related to photovoltaic performance measurements obtained with a classified solar simulator.
SCOPE
1.1 This specification provides means for classifying solar simulators intended for indoor testing of photovoltaic devices (solar cells or modules), according to their spectral match to a reference spectral irradiance, non-uniformity of spatial irradiance, and temporal instability of irradiance.
1.2 Testing of photovoltaic devices may require the use of solar simulators. Test Methods that require specific classification of simulators as defined in this specification include Test Methods E948, E1036, and E1362.
1.3 This standard is applicable to both pulsed and steady state simulators and includes recommended test requirements used for classifying such simulators.
1.4 A solar simulator usually consists of three major components: (1) light source(s) and associated power supply; (2) any optics and filters required to modify the output beam to meet the classification requirements in Section 4; and (3) the necessary controls to operate the simulator, adjust irradiance, etc.
1.5 A light source that does not meet all of the defined requirements for classification presented in this document may not be referred to as a solar simulator.
1.6 Spectral irradiance classifications are provided for Air Mass 1.5 direct and global (as defined in Tables G173), or Air Mass 0 (AM0, as defined in Standard E490).
1.7 The classification of a solar simulator is based on the size of the test plane; simulators with smaller test plane areas have tighter specifications for non-uniformity of spatial irradiance.
1.8 The data acquisition system may affect the ability to synchronize electrical measurements with variations in irradiance and therefore may be included in this specification. In all cases, the manufacturer must specify with the temporal instability classification: (1) how the classification was determined; and (2) the conditions under which the classification was determined.
1.9 The classification of a solar simulator does not provide any information about electrical measurement errors that are related to photovoltaic performance measurements obtained with a classified solar simulator. Such errors are dependent on the actual instrumentation and procedures used.
1.10 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.11 The following precautionary caveat pertains only to the hazards portion, Section 6, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:E927 −10 (Reapproved 2015) An American National Standard
Standard Specification for
1
Solar Simulation for Photovoltaic Testing
This standard is issued under the fixed designation E927; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope bility classification: (1) how the classification was determined;
and (2) the conditions under which the classification was
1.1 This specification provides means for classifying solar
determined.
simulators intended for indoor testing of photovoltaic devices
1.9 The classification of a solar simulator does not provide
(solar cells or modules), according to their spectral match to a
any information about electrical measurement errors that are
reference spectral irradiance, non-uniformity of spatial
related to photovoltaic performance measurements obtained
irradiance, and temporal instability of irradiance.
with a classified solar simulator. Such errors are dependent on
1.2 Testing of photovoltaic devices may require the use of
the actual instrumentation and procedures used.
solar simulators. Test Methods that require specific classifica-
1.10 The values stated in SI units are to be regarded as
tion of simulators as defined in this specification include Test
standard. No other units of measurement are included in this
Methods E948, E1036, and E1362.
standard.
1.3 This standard is applicable to both pulsed and steady
1.11 Thefollowingprecautionarycaveatpertainsonlytothe
state simulators and includes recommended test requirements
hazards portion, Section 6, of this specification. This standard
used for classifying such simulators.
does not purport to address all of the safety concerns, if any,
1.4 A solar simulator usually consists of three major com-
associated with its use. It is the responsibility of the user of this
ponents: (1) light source(s) and associated power supply; (2)
standard to establish appropriate safety, health, and environ-
any optics and filters required to modify the output beam to
mental practices and determine the applicability of regulatory
meet the classification requirements in Section 4; and (3) the
limitations prior to use.
necessary controls to operate the simulator, adjust irradiance,
1.12 This international standard was developed in accor-
etc.
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the
1.5 A light source that does not meet all of the defined
Development of International Standards, Guides and Recom-
requirements for classification presented in this document may
mendations issued by the World Trade Organization Technical
not be referred to as a solar simulator.
Barriers to Trade (TBT) Committee.
1.6 Spectral irradiance classifications are provided for Air
Mass 1.5 direct and global (as defined in Tables G173), or Air
2. Referenced Documents
Mass 0 (AM0, as defined in Standard E490).
2
2.1 ASTM Standards:
1.7 The classification of a solar simulator is based on the
E490 Standard Solar Constant and Zero Air Mass Solar
size of the test plane; simulators with smaller test plane areas
Spectral Irradiance Tables
have tighter specifications for non-uniformity of spatial irradi-
E772 Terminology of Solar Energy Conversion
ance.
E948 Test Method for Electrical Performance of Photovol-
taic Cells Using Reference Cells Under Simulated Sun-
1.8 The data acquisition system may affect the ability to
light
synchronize electrical measurements with variations in irradi-
E1036 Test Methods for Electrical Performance of Noncon-
ance and therefore may be included in this specification. In all
centrator Terrestrial Photovoltaic Modules and Arrays
cases, the manufacturer must specify with the temporal insta-
Using Reference Cells
E1328 Terminology Relating to Photovoltaic Solar Energy
1
This specification is under the jurisdiction of ASTM Committee E44 on Solar,
Geothermal and OtherAlternative Energy Sources and is the direct responsibility of
2
Subcommittee E44.09 on Photovoltaic Electric Power Conversion. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Nov. 1, 2015. Published November 2015. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1983. Last previous edition approved in 2010 as E927 –10. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/E0927-10R15. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
E927−
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: E927 − 10 E927 − 10 (Reapproved 2015)
Standard Specification for
1
Solar Simulation for Photovoltaic Testing
This standard is issued under the fixed designation E927; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification provides means for classifying solar simulators intended for indoor testing of photovoltaic devices (solar
cells or modules), according to their spectral match to a reference spectral irradiance, non-uniformity of spatial irradiance, and
temporal instability of irradiance.
1.2 Testing of photovoltaic devices may require the use of solar simulators. Test Methods that require specific classification of
simulators as defined in this specification include Test Methods E948, E1036, and E1362.
1.3 This standard is applicable to both pulsed and steady state simulators and includes recommended test requirements used for
classifying such simulators.
1.4 A solar simulator usually consists of three major components: (1) light source(s) and associated power supply; (2) any optics
and filters required to modify the output beam to meet the classification requirements in Section 4; and (3) the necessary controls
to operate the simulator, adjust irradiance, etc.
1.5 A light source that does not meet all of the defined requirements for classification presented in this document may not be
referred to as a solar simulator.
1.6 Spectral irradiance classifications are provided for Air Mass 1.5 direct and global (as defined in Tables G173), or Air Mass
0 (AM0, as defined in Standard E490).
1.7 The classification of a solar simulator is based on the size of the test plane; simulators with smaller test plane areas have
tighter specifications for non-uniformity of spatial irradiance.
1.8 The data acquisition system may affect the ability to synchronize electrical measurements with variations in irradiance and
therefore may be included in this specification. In all cases, the manufacturer must specify with the temporal instability
classification: (1) how the classification was determined; and (2) the conditions under which the classification was determined.
1.9 The classification of a solar simulator does not provide any information about electrical measurement errors that are related
to photovoltaic performance measurements obtained with a classified solar simulator. Such errors are dependent on the actual
instrumentation and procedures used.
1.10 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
6, of this specification. This standard does
1.11 The following precautionary caveat pertains only to the hazards portion, Section
not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard
to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
E490 Standard Solar Constant and Zero Air Mass Solar Spectral Irradiance Tables
E772 Terminology of Solar Energy Conversion
E948 Test Method for Electrical Performance of Photovoltaic Cells Using Reference Cells Under Simulated Sunlight
E1036 Test Methods for Electrical Performance of Nonconcentrator Terrestrial Photovoltaic Modules and Arrays Using
Reference Cells
1
This specification is under the jurisdiction of ASTM Committee E44 on Solar, Geothermal and Other Alternative Energy Sources and is the direct responsibility of
Subcommittee E44.09 on Photovoltaic Electric Power Conversion.
Current edition approved June 1, 2010Nov. 1, 2015. Published July 2010November 2015. Originally approved in 1983. Last previous edition approved in 20052010 as
E927 – 05.E927 –10. DOI: 10.1520/E0927-10.10.1520/E0927-10R15.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
E927 − 10 (2015)
3
E1328 Terminology Relating to Photovoltaic Solar Energy Conversion (Withdrawn 2012)
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.