iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D6922-13(2018)

(Test Method)

Standard Test Method for Determination of Homogeneity and Miscibility in Automotive Engine Oils

Standard Test Method for Determination of Homogeneity and Miscibility in Automotive Engine Oils

SIGNIFICANCE AND USE
5.1 It is important that engine oils from different manufacturers be homogeneous and miscible with each other, because operators of automotive engines often do not have prior knowledge of the manufacturer of the oil that is currently used in their application, and engine failure can occur if oils are combined that do not stay homogeneous and function properly.
SCOPE
1.1 This test method covers the determination if an automotive engine oil is homogeneous and will remain so, and if it is miscible with certain standard reference oils after being submitted to a prescribed cycle of temperature changes. This test method is very similar to the homogeneity and miscibility test described in FED–STD–791/3470.1.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 WARNING—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use Caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
30-Nov-2018
ICS
75.100 - Lubricants, industrial oils and related products
Technical Committee
D02 - Petroleum Products, Liquid Fuels, and Lubricants
Drafting Committee
D02.B0 - Automotive Lubricants
Current Stage
Ref Project

Relations

Refers
ASTM E344-16 - Terminology Relating to Thermometry and Hydrometry
Effective Date
01-Nov-2016
Refers
ASTM E344-18 - Terminology Relating to Thermometry and Hydrometry
Effective Date
01-Apr-2018
Refers
ASTM E344-19 - Terminology Relating to Thermometry and Hydrometry
Effective Date
01-Sep-2019
Referred By
ASTM D4485-22e1 - Standard Specification for Performance of Active API Service Category Engine Oils
Effective Date
01-Dec-2018

Buy Standard

ASTM D6922-13(2018) - Standard Test Method for Determination of Homogeneity and Miscibility in Automotive Engine OilsASTM D6922-13(2018) - Standard Test Method for Determination of Homogeneity and Miscibility in Automotive Engine Oils
PreviousNext
Standard
ASTM D6922-13(2018) - Standard Test Method for Determination of Homogeneity and Miscibility in Automotive Engine Oils
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D6922 − 13 (Reapproved 2018)
Standard Test Method for
Determination of Homogeneity and Miscibility in Automotive
1
Engine Oils
This standard is issued under the fixed designation D6922; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2
1.1 Thistestmethodcoversthedeterminationifanautomo- 2.1 ASTM Standards:
tive engine oil is homogeneous and will remain so, and if it is D97Test Method for Pour Point of Petroleum Products
miscible with certain standard reference oils after being sub- D4057Practice for Manual Sampling of Petroleum and
mitted to a prescribed cycle of temperature changes. This test Petroleum Products
method is very similar to the homogeneity and miscibility test D5844Test Method for Evaluation of Automotive Engine
described in FED–STD–791/3470.1. Oils for Inhibition of Rusting (Sequence IID) (Withdrawn
3
2003)
1.2 The values stated in SI units are to be regarded as
D6557Test Method for Evaluation of Rust Preventive Char-
standard. No other units of measurement are included in this
acteristics of Automotive Engine Oils
standard.
E1Specification for ASTM Liquid-in-Glass Thermometers
1.3 WARNING—Mercury has been designated by many
E344Terminology Relating to Thermometry and Hydrom-
regulatory agencies as a hazardous substance that can cause
etry
serious medical issues. Mercury, or its vapor, has been dem-
4
2.2 Federal Test Method Standard:
onstrated to be hazardous to health and corrosive to materials.
FED–STD–791/3470.1HomogeneityandMiscibilityofOils
Use Caution when handling mercury and mercury-containing
products. See the applicable product Safety Data Sheet (SDS)
3. Terminology
for additional information. The potential exists that selling
3.1 Definitions:
mercury or mercury-containing products, or both, is prohibited
3.1.1 calibrate, v—todeterminetheindicationoroutputofa
bylocalornationallaw.Usersmustdeterminelegalityofsales
measuring device with the respect of that of a standard. E344
in their location.
3.1.2 homogeneity, n—theabilityofatestoilitselftoremain
1.4 This standard does not purport to address all of the
the same in appearance throughout (uniform) after submission
safety concerns, if any, associated with its use. It is the
to a series of temperature changes.
responsibility of the user of this standard to establish appro-
3.1.3 miscibility, n—theabilityofareferenceoilandtestoil
priate safety, health, and environmental practices and deter-
to form a uniform mixture after blending and not separate into
mine the applicability of regulatory limitations prior to use.
twophasesaftersubmissiontoaseriesoftemperaturechanges.
1.5 This international standard was developed in accor-
dance with internationally recognized principles on standard-
3.1.4 reference oil, n—an oil of known performance
ization established in the Decision on Principles for the
characteristics, used as a basis for comparison.
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
2
Barriers to Trade (TBT) Committee. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
1
This test method is under the jurisdiction of ASTM Committee D02 on the ASTM website.
3
Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of The last approved version of this historical standard is referenced on
Subcommittee D02.B0 on Automotive Lubricants. www.astm.org.
4
Current edition approved Dec. 1, 2018. Published December 2018. Originally AvailablefromU.S.GovernmentPrintingOfficeSuperintendentofDocuments,
approved in 2003. Last previous edition approved in 2013 as D6922–13. 732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401, http://
DOI:10.1520/D6922-13R18. www.access.gpo.gov.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D6922 − 13 (2018)
3.1.4.1 Discussion—Reference oils are used to calibrate 6.6 Gasket—a ring gasket, about 5.0 mm in thickness, to fit
testing facilities, to compare the performance of other oils, or snugly around the outside of the test jar and loosely inside the
to evaluate other materials (such as seals) that interact with jack
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D6439-23(Guide)
Standard Guide for Cleaning, Flushing, and Purification of Steam, Gas, and Hydroelectric Turbine Lubrication Systems

SIGNIFICANCE AND USE
4.1 This guide is intended to aid the equipment manufacturer, installer, service company, and turbine operator in coordinating their efforts to obtain and maintain clean lubrication and control systems.  
4.2 The flushing and cleaning philosophies stated in this guide are applicable to both large and small lubrication systems.  
4.3 Clean lubrication systems result from proper system design and good planning, execution, and communication by all involved during commissioning. No phase of these procedures should be undertaken without a thorough understanding of the possible effects of improper system preparation. The installation, cleaning, and flushing of the equipment should not be entrusted to persons lacking in experience.  
4.4 Because of the knowledge and specialized equipment that is required, the operator may wish to employ an outside specialist contractor for the system flushing. Review of this guide can provide guidelines for discussion with prospective contractors.
SCOPE
1.1 This guide covers types of contaminants, oil purification devices, contamination monitoring, contamination control during building or refurbishing of turbine systems, lubrication system flushing, and maintenance of pure lubrication oil.  
1.2 To obtain maximum operating life and reliability, or lubricants and system, it is vital that the turbine lubrication system has pure oil. This guide is intended to aid the equipment manufacturer, installer, and turbine operator in coordinating their efforts to obtain and maintain clean lubrication and control systems. These systems may be on land or marine turbine generators and propulsion and mechanical drive equipment. This guide is generalized due to variations in the type of equipment, builder's practices, and operating conditions.  
1.3 This guide primarily addresses petroleum based lubricating oil. For systems using nonpetroleum based fluids, this guide may not be appropriate. For nonpetroleum products, consult the equipment and fluid manufacturers.  
1.4 This guide is applicable to both large and small lubrication systems. Some equipment specified herein, however, may not be appropriate for all systems. Moreover, in situations where specific guidelines and procedures are provided by the equipment manufacturer, such procedures should take precedence over the recommendations of this guide.  
1.5 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    20 pages
    English language
    sale 15% off
  • Guide
    20 pages
    English language
    sale 15% off
ASTM
ASTM D6138-23a(Test Method)
Standard Test Method for Determination of Corrosion-Preventive Properties of Lubricating Greases Under Dynamic Wet Conditions (Emcor Test)

SIGNIFICANCE AND USE
5.1 This test method is used to assess the ability of grease to prevent corrosion in rolling bearings operated in the presence of distilled water, sodium chloride solution, or synthetic sea water. It is used for development and specification purposes.
SCOPE
1.1 This test method covers the determination of corrosion-preventive properties of greases using grease-lubricated ball bearings under dynamic wet conditions.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D4742-23(Test Method)
Standard Test Method for Oxidation Stability of Gasoline Automotive Engine Oils by Thin-Film Oxygen Uptake (TFOUT)

SIGNIFICANCE AND USE
5.1 This test method is used to evaluate oxidation stability of lubricating base oils with additives in the presence of chemistries similar to those found in gasoline engine service. Test results on some ASTM reference oils have been found to correlate with sequence IIID engine test results in hours for a 375 % viscosity increase.5 The test does not constitute a substitute for engine testing, which measures wear, oxidation stability, volatility, and deposit control characteristics of lubricants. Properly interpreted, the test may provide input on the oxidation stability of lubricants under simulated engine chemistry.  
5.2 This test method is intended to be used as a bench screening test and quality control tool for lubricating base oil manufacturing, especially for re-refined lubricating base oils. This test method is useful for quality control of oxidation stability of re-refined oils from batch to batch.  
5.3 This test method is useful for screening formulated oils prior to engine tests. Within similar additive chemistry and base oil types, the ranking of oils in this test appears to be predictive of ranking in engine tests. When oils having completely different additive chemistry or base oil type are compared, oxidation stability results may not reflect the actual engine test result.  
5.4 Other oxidation stability test methods have demonstrated that soluble metal catalyst supplies are very inconsistent and they have significant effects on the test results. Thus, for test comparisons, the same source and same batch of metal naphthenates shall be used.
Note 2: It is also recommended as a good research practice not to use different batches of the fuel component in test comparisons.
SCOPE
1.1 This test method evaluates the oxidation stability of engine oils for gasoline automotive engines. This test, run at 160 °C, utilizes a high pressure reactor pressurized with oxygen along with a metal catalyst package, a fuel catalyst, and water in a partial simulation of the conditions to which an oil may be subjected in a gasoline combustion engine. This test method can be used for engine oils with viscosity in the range from 4 mm2/s (cSt) to 21 mm2/s (cSt) at 100 °C, including re-refined oils.  
1.2 This test method is not a substitute for the engine testing of an engine oil in established engine tests, such as Sequence IIID.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3.1 Exception—Pressure units are provided in psig, and dimensions are provided in inches in Annex A1, because these are the industry accepted standard and the apparatus is built according to the figures shown.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Sections 7 and 8.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM D2266-23(Test Method)
Standard Test Method for Wear Preventive Characteristics of Lubricating Grease (Four-Ball Method)

SIGNIFICANCE AND USE
5.1 The four-ball wear-test method can be used to determine the relative wear-preventing properties of greases under the test conditions and if the test conditions are changed the relative ratings may be different. No correlation has been established between the four-ball wear test and field service. The test method cannot be used to differentiate between Extreme Pressure (EP) and Non-Extreme Pressure (Non-EP) Greases.4
SCOPE
1.1 This test method covers the determination of the wear preventive characteristics of greases in sliding steel-on-steel applications. It is not intended to predict wear characteristics with metal combinations other than steel-on-steel or to evaluate the extreme pressure characteristics of the grease.  
1.2 The values stated in SI units are to be regarded as the standard except where the test apparatus or consumable parts are only available in other units. In such cases, these will be regarded as standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6923-23(Test Method)
Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1R Test Procedure

SIGNIFICANCE AND USE
5.1 This is an accelerated engine oil test, performed in a standardized, calibrated, stationary single-cylinder diesel engine that gives a measure of (1) piston and ring groove deposit forming tendency, (2) piston, ring, and liner scuffing and (3) oil consumption. The test is used in the establishment of diesel engine oil specification requirements as cited in Specification D4485 for appropriate API Performance Category C oils (API 1509). The test method can also be used in diesel engine oil development.
SCOPE
1.1 This test method covers stressing an engine oil under modern high-speed diesel operating conditions and measures the oil's deposit control, lubrication ability, and resistance to oil consumption. It is performed in a laboratory using a standardized high-speed, single-cylinder diesel engine.3  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—Where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, and tubing size, or where a sole source supplier is specified.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Being an engine test method, this test method does have definite hazards that require safe practices (see Appendix X2 on Safety).  
1.4 The following is the Table of Contents:    
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Summary of Test Method  
4  
Significance and Use  
5  
Apparatus and Installation  
6  
Intake Air System  
6.2.1  
Exhaust System  
6.2.2  
Fuel System  
6.2.3  
Oil Consumption System  
6.2.4  
Engine Oil System  
6.2.5  
Engine Coolant System  
6.2.6  
Engine Instrumentation  
6.2.7  
Reagents and Materials  
7  
Oil Samples  
8  
Preparation of Apparatus  
9  
General Engine Assembly Practices  
9.1  
Complete Engine Inspection  
9.2  
Copper Component  
9.3  
Engine Lubricant System Flush  
9.4  
Engine Piston Cooling Jet  
9.5  
Engine Measurements and Inspections  
9.6  
Cylinder Head  
9.7  
Valve Guide Bushings  
9.8  
Fuel Injector  
9.9  
Piston and Rings  
9.10  
Cylinder Liner  
9.11  
Compression Ratio  
9.12  
Engine Timing  
9.13  
Engine Coolant System Cleaning Procedure  
9.14  
Calibration and Standardization  
10  
Test Cell Instrumentation  
10.1  
Instrumentation Standards  
10.2  
Coolant Flow  
10.3  
Fuel Injectors  
10.4  
Air Flow  
10.5  
Intake Air Barrel  
10.6  
Fuel Filter  
10.7  
Oil Scale Flow Rates  
10.8  
Test Stand Calibration  
10.9  
Re-calibration Requirements  
10.9.1  
Extending Test Stand Calibration Period  
10.9.2  
Test Run Numbering  
10.10  
Humidity Calibration Requirements  
10.11  
Calibration of Piston Deposit Raters  
10.12  
Procedure  
11  
Engine Break-in Procedure  
11.1  
Cool-down Procedure  
11.2  
Warm-up Procedure  
11.3  
Shutdowns and Lost Time  
11.4  
Periodic Measurements  
11.5  
Engine Control Systems  
11.6  
Engine Coolant  
11.6.1  
Engine Fuel System  
11.6.2  
Engine Oil Temperature  
11.6.3  
Exhaust Pressure  
11.6.4  
Intake Air  
11.6.5  
Post-Test Procedures  
11.7  
Piston Ring Side Clearances  
11.7.1  
Piston Ratings  
11.7.2  
Ring Gap End Increase  
11.7.3  
Cylinder Liner Wear  
11.7.4  
Cylinder Liner Bore Polish  
11.7.5  
Photographs  
11.7.6  
Calculation and Interpretation of Results  
12  
Test Validity  
12.1  
Calculations  
12.4  
Quality Index  
12.4.1  
Oil Consumption  
12.4.2  
Report  
13  
Form...

  • Standard
    65 pages
    English language
    sale 15% off
  • Standard
    65 pages
    English language
    sale 15% off
ASTM
ASTM D6681-23(Test Method)
Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1P Test Procedure

SIGNIFICANCE AND USE
5.1 This is an accelerated engine oil test, performed in a standardized, calibrated, stationary single-cylinder diesel engine that gives a measure of (1) piston and ring groove deposit forming tendency, (2) piston, ring and liner scuffing and (3) oil consumption. The test is used in the establishment of diesel engine oil specification requirements as cited in Specification D4485 for appropriate API Performance Category C oils (API 1509). The test method can also be used in diesel engine oil development.
SCOPE
1.1 This test method covers and is required to evaluate the performance of engine oils intended to satisfy certain American Petroleum Institute (API) C service categories (included in Specification D4485). It is performed in a laboratory using a standardized high-speed, single-cylinder diesel engine.4 Piston and ring groove deposit-forming tendency and oil consumption is measured. The piston, the rings, and the liner are also examined for distress and the rings for mobility.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—Where there is no direct SI equivalent such as screw threads, National Pipe Threads/diameters, tubing size, or where there is a sole source supply equipment specification.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Being an engine test method, this standard does have definite hazards that require safe practices (see Appendix X2 on Safety).  
1.4 The following is the Table of Contents:    
Section  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Summary of Test Method  
4  
Significance and Use  
5  
Apparatus and Installation  
6  
Intake Air System  
6.2.1  
Exhaust System  
6.2.2  
Fuel System  
6.2.3  
Oil Consumption System  
6.2.4  
Engine Oil System  
6.2.5  
Oil Heating System  
6.2.5.1  
Oil Sample Valve  
6.2.5.2  
Engine Coolant System  
6.2.6  
Engine Instrumentation  
6.2.7  
Reagents and Materials  
7  
Oil Samples  
8  
Preparation of Apparatus  
9  
General Engine Assembly Practices  
9.1  
Complete Engine Inspection  
9.2  
Copper Components  
9.3  
Engine Lubricant System Flush  
9.4  
Engine Piston Cooling Jets  
9.5  
Engine Measurements and Inspections  
9.6  
Cylinder Head  
9.7  
Valve Guide Bushings  
9.8  
Fuel Injector  
9.9  
Piston and Rings  
9.10  
Cylinder Liner  
9.11  
Compression Ratio  
9.12  
Engine Timing  
9.13  
Engine Coolant System Cleaning Procedure  
9.14  
Calibration and Standardization  
10  
Test Cell Instrumentation  
10.1  
Instrumentation Standards  
10.2  
Coolant Flow  
10.3  
Re-calibration Requirements  
10.4  
Fuel Injectors  
10.5  
Air Flow  
10.6  
Intake Air Barrel  
10.7  
Fuel Filter  
10.8  
Oil Scale Flow Rates  
10.9  
Calibration of Test Stands  
10.10  
Extending Test Stand Calibration Period  
10.11  
Test Run Numbering  
10.13  
Humidity Calibration Requirements  
10.14  
Calibration of Piston Deposit Raters  
10.15  
Procedure  
11  
Engine Break-in Procedure  
11.1  
Cool-down Procedure  
11.2  
Warm-up Procedure  
11.3  
Shutdowns and Lost Time  
11.4  
Periodic Measurements  
11.5  
Engine Control Systems  
11.6  
Engine Coolant  
11.6.1  
Engine Fuel System  
11.6.2  
Engine Oil Temperature  
11.6.3  
Exhaust Pressure  
11.6.4  
Intake Air  
11.6.5  
Post-Test Procedures  
11.7  
Piston Ring Side Clearances  
11.7.1  
Piston Ratings  
11.7.2  
Referee Ratings  
11.7.3  
Ring End Gap...

  • Standard
    57 pages
    English language
    sale 15% off
  • Standard
    57 pages
    English language
    sale 15% off
ASTM
ASTM D6891-23(Test Method)
Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IVA Spark-Ignition Engine

SIGNIFICANCE AND USE
5.1 This test method was developed to evaluate automotive lubricant’s effect on controlling cam lobe wear for overhead valve-train equipped engines with sliding cam followers.
Note 1: This test method may be used for engine oil specifications, such as Specification D4485, API 1509, SAE J183, and ILSC GF 3.
SCOPE
1.1 This test method measures the ability of crankcase oil to control camshaft lobe wear for spark-ignition engines equipped with an overhead valve-train and sliding cam followers. This test method is designed to simulate extended engine idling vehicle operation. The Sequence IVA Test Method uses a Nissan KA24E engine. The primary result is camshaft lobe wear (measured at seven locations around each of the twelve lobes). Secondary results include cam lobe nose wear and measurement of iron wear metal concentration in the used engine oil. Other determinations such as fuel dilution of crankcase oil, non-ferrous wear metal concentrations, and total oil consumption, can be useful in the assessment of the validity of the test results.2  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—Where there is no direct SI equivalent such as pipe fittings, tubing, NPT screw threads/diameters, or single source equipment specified.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Annex A8 for specific safety precautions.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    46 pages
    English language
    sale 15% off
  • Standard
    46 pages
    English language
    sale 15% off
ASTM
ASTM D6750-23(Test Method)
Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur)

SIGNIFICANCE AND USE
5.1 These are accelerated engine oil tests (known as the 1K and 1N test procedures), performed in a standardized, calibrated, stationary single-cylinder diesel engine using either mass fraction 0.4 % sulfur fuel (1K test) or mass fraction 0.04 % sulfur fuel (1N test), that give a measure of (1) piston and ring groove deposit forming tendency, (2) piston, ring and liner scuffing and (3) oil consumption.  
5.2 The 1K test was correlated with vehicles equipped with certain multi-cylinder direct injection engines used in heavy duty and high speed service prior to 1989, particularly with respect to aluminum piston deposits, and oil consumption, when fuel sulfur was nominally mass fraction 0.4 %. These data are given in Research Report RR:D02-1273.9  
5.3 The 1N test has been used to predict piston deposit formation in four-stroke cycle, direct injection, diesel engines that have been calibrated to meet 1994 U.S. federal exhaust emission requirements for heavy-duty engines operated on fuel containing less than mass fraction 0.05 % sulfur. See Research Report RR:D02-1321.9  
5.4 These test methods are used in the establishment of diesel engine oil specification requirements as cited in Specification D4485 for appropriate API Performance Category oils (API 1509).  
5.5 These test methods are also used in diesel engine oil development.
SCOPE
1.1 These test methods cover the performance of engine oils intended for use in certain diesel engines. They are performed in a standardized high-speed, single-cylinder diesel engine by either the 1K (0.4 % mass fuel sulfur) or 1N (0.04 % mass fuel sulfur) procedure.3 The only difference in the two test methods is the fuel used. Piston and ring groove deposit-forming tendency and oil consumption are measured. Also, the piston, the rings, and the liner are examined for distress and the rings for mobility. These test methods are required to evaluate oils intended to satisfy API service categories CF-4 and CH-4 for 1K, and CG-4 for 1N of Specification D4485.  
1.2 These test methods, although based on the original Caterpillar 1K/1N procedures,3 also embody TMC information letters issued before these test methods were first published. These test methods are subject to frequent change. Until the next revision of these test methods, TMC will update changes in these test methods by the issuance of information letters which shall be obtained from TMC (see Annex A1 – Annex A4).  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3.1 Exception—Where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, tubing size, or single source equipment specified. Also Brake Specific Fuel Consumption is measured in kilograms per kilowatthour.  
1.4 The following is the Table of Contents:    
Section  
Introduction  
Scope  
1  
Referenced documents  
2  
Terminology  
3  
Summary of Test Methods  
4  
Significance and Use  
5  
Apparatus  
6  
General Laboratory Requirements  
6.1  
Test Engine  
6.2  
Test Engine Accessories and Parts  
6.3  
Reagents and Materials  
7  
Test Oil Sample Requirements  
8  
Preparation of Apparatus  
9  
Engine Inspection  
9.1  
Engine Pre-Test Lubrication System Flush  
9.2  
Engine Pre-Test Measurements and Inspections  
9.3  
Engine Assembly  
9.4  
Pressure Testing of Fuel System Assembly  
9.5  
Calibration of Engine Test Stand  
10  
General Requirements and Frequency of Calibration  
10.1  
Runs  
10.2  
Specified Test Parameters  
10.3  
Calibration Test Acceptance Criteria  
10.4  
Action on Rejection of Calibration Test  
10.5  
Test Numbering  
10.6  
Reference Oils  
10.7  
Severity Adjustments  
10.8  
Engine Operating Procedure  
11  
...

  • Standard
    70 pages
    English language
    sale 15% off
  • Standard
    70 pages
    English language
    sale 15% off
ASTM
ASTM D7549-23(Test Method)
Standard Test Method for Evaluation of Heavy-Duty Engine Oils under High Output Conditions—Caterpillar C13 Test Procedure

SIGNIFICANCE AND USE
5.1 This test method assesses the performance of an engine oil with respect to control of piston deposits and maintenance of oil consumption under heavy-duty operating conditions selected to accelerate deposit formation in a turbocharged, intercooled four-stroke-cycle diesel engine equipped with a combustion system that minimizes federally controlled exhaust gas emissions.  
5.2 The results from this test method may be compared against specification requirements to ascertain acceptance.  
5.3 The design of the test engine used in this test method is representative of many, but not all, diesel engines. This factor, along with the accelerated operating conditions, needs to be considered when comparing test results against specification requirements.
SCOPE
1.1 The test method covers a heavy-duty engine test procedure under high output conditions to evaluate engine oil performance with regard to piston deposit formation, piston ring sticking and oil consumption control in a combustion environment designed to minimize exhaust emissions. This test method is commonly referred to as the Caterpillar C13 Heavy-Duty Engine Oil Test.3  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—Where there are no SI equivalent such as screw threads, National Pipe Treads (NPT), and tubing sizes.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Annex A1 for general safety precautions.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    37 pages
    English language
    sale 15% off
  • Standard
    37 pages
    English language
    sale 15% off
ASTM
ASTM D5770-23(Test Method)
Standard Test Method for Semiquantitative Micro Determination of Acid Number of Lubricating Oils During Oxidation Testing

SIGNIFICANCE AND USE
5.1 This test method provides a semiquantitative estimate of the acid number of lubricating oils obtained from laboratory oxidation tests using smaller amounts of sample than Test Methods D974, D664, or D3339. It has specific application in Test Method D943 and in Test Method D4871. This test method, therefore, provides a means of monitoring the relative oxidation of lubricating oils by measuring changes in acid number, at different time intervals and under various oxidizing test conditions.  
5.2 Since this test method is semiquantitative, each laboratory shall develop its own criteria for each oxidation test method for determining when to switch from this semiquantitative test method to a more precise test method for acid number.
SCOPE
1.1 This test method is a semiquantitative micro method intended for monitoring the changes in acidic constituents occurring in lubricating oils during oxidation testing, when the acid number of such oils falls within the range from 0.02 mg to 1.0 mg of potassium hydroxide per gram of sample. It is applicable to such oils as turbine oils, hydraulic oils, and other circulating oils.  
Note 1: This test method is a micro version of Test Method D974 and it produces results similar to that method.  
1.2 This test method is designed for use where sample size is limited. It shall not be used as a replacement for higher precision methods such as Test Methods D974 or D664. It shall not be used to monitor oils in-service.  
1.3 The values stated in SI units are to be regarded as the standard.  
1.3.1 Exception—The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off