ASTM F2906-23

Standard Consumer Safety Specification for Bedside Sleepers

ABSTRACT
This specification is intended for consumer safety and establishes performance requirements, test methods, and marking requirements to promote safe use of bedside sleepers. It explains the test methods that are conducted on all bedside sleepers, namely the product disengagement test method, the product disengagement rationale, and the folding latch test method.
SCOPE
1.1 This consumer safety specification establishes performance requirements, test methods, and marking requirements to promote safe use of bedside sleepers.  
1.2 This consumer safety specification is intended to minimize the risk of injury to an infant from the normal use and reasonably foreseeable misuse of a bedside sleeper.  
1.3 This consumer safety performance specification covers products intended to provide sleeping space for an infant up to approximately 5 months of age (or when child begins to push up on hands and knees). These products are intended to be secured to the side of an adult bed for the purpose of having a baby sleep in close proximity to an adult.  
1.4 No bedside sleeper produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with the specification unless it complies with all of the requirements contained herein.  
1.5 This consumer safety performance specification is not intended to address incidents and injuries resulting from alteration or unreasonable abuse or misuse of the product by a child or child care provider.  
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.7 The following precautionary caveat pertains only to the test method portion, Section 6 of this consumer safety performance specification. This standard may involve the use of hazardous materials, operations and equipment.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Published
• Publication Date: 31-Dec-2022
• ICS: 97.140 - Furniture
• ICS: 97.190 - Equipment for children
• Technical Committee: F15 - Consumer Products
• Drafting Committee: F15.18 - Cribs, Toddler Beds, Play Yards, Bassinets, Cradles and Baby Changing Products

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:F2906 −23
Standard Consumer Safety Specification for
1
Bedside Sleepers
This standard is issued under the fixed designation F2906; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This consumer safety specification is intended to address incidents reported by the U.S. Consumer
Product Safety Commission (CPSC) relating to bedside sleepers.
In response to the incident data compiled by the CPSC, this consumer safety specification attempts
to minimize the hazards associated with these products from the following: (1) occupant retention, (2)
structural integrity and product assembly, and (3) deficiency of consumer education regarding product
use.This consumer safety specification is intended to deal with reasonably foreseeable use and misuse
of the products. This consumer safety specification does not apply to products that are blatantly
misused, nor does it apply to products used by consumers in a careless manner that violate normal
practice or disregard the instructions or warnings provided with the product, or both.
1. Scope conversions to SI units that are provided for information only
and are not considered standard.
1.1 This consumer safety specification establishes perfor-
1.7 The following precautionary caveat pertains only to the
mance requirements, test methods, and marking requirements
test method portion, Section 6 of this consumer safety perfor-
to promote safe use of bedside sleepers.
mance specification. This standard may involve the use of
1.2 This consumer safety specification is intended to mini-
hazardous materials, operations and equipment. This standard
mize the risk of injury to an infant from the normal use and
does not purport to address all of the safety concerns, if any,
reasonably foreseeable misuse of a bedside sleeper.
associated with its use. It is the responsibility of the user of this
1.3 This consumer safety performance specification covers
standard to establish appropriate safety, health, and environ-
products intended to provide sleeping space for an infant up to
mental practices and determine the applicability of regulatory
approximately 5 months of age (or when child begins to push
limitations prior to use.
up on hands and knees). These products are intended to be
1.8 This international standard was developed in accor-
secured to the side of an adult bed for the purpose of having a
dance with internationally recognized principles on standard-
baby sleep in close proximity to an adult.
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
1.4 No bedside sleeper produced after the approval date of
mendations issued by the World Trade Organization Technical
this consumer safety specification shall, either by label or other
Barriers to Trade (TBT) Committee.
means, indicate compliance with the specification unless it
complies with all of the requirements contained herein.
2. Referenced Documents
1.5 This consumer safety performance specification is not
2
2.1 ASTM Standards:
intended to address incidents and injuries resulting from
F2085 ConsumerSafetySpecificationforPortableBedRails
alteration or unreasonable abuse or misuse of the product by a
F2194 Consumer Safety Specification for Bassinets and
child or child care provider.
Cradles
1.6 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical
3. Terminology
3.1 Definitions:
1
This consumer safety specification is under the jurisdiction ofASTM Commit-
tee F15 on Consumer Products and is the direct responsibility of Subcommittee
F15.18 on Cribs, Toddler Beds, Play Yards, Bassinets, Cradles and Baby Changing
2
Products. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Jan. 1, 2023. Published January 2023. Originally contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
approved in 2011. Last previous edition approved in 2022 as F2906 – 22. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/F2906-23. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2906−23
3.1.1 attachment system, n—the means used to attach the 4. Calibration and Standardization
bedside sleeper to the adult bed.
4.1 All te
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2906 − 22 F2906 − 23
Standard Consumer Safety Specification for
1
Bedside Sleepers
This standard is issued under the fixed designation F2906; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This consumer safety specification is intended to address incidents reported by the U.S. Consumer
Product Safety Commission (CPSC) relating to bedside sleepers.
In response to the incident data compiled by the CPSC, this consumer safety specification attempts
to minimize the hazards associated with these products from the following: (1) occupant retention, (2)
structural integrity and product assembly, and (3) deficiency of consumer education regarding product
use. This consumer safety specification is intended to deal with reasonably foreseeable use and misuse
of the products. This consumer safety specification does not apply to products that are blatantly
misused, nor does it apply to products used by consumers in a careless manner that violate normal
practice or disregard the instructions or warnings provided with the product, or both.
1. Scope
1.1 This consumer safety specification establishes performance requirements, test methods, and marking requirements to promote
safe use of bedside sleepers.
1.2 This consumer safety specification is intended to minimize the risk of injury to an infant from the normal use and reasonably
foreseeable misuse of a bedside sleeper.
1.3 This consumer safety performance specification covers products intended to provide sleeping space for an infant up to
approximately 5 months of age (or when child begins to push up on hands and knees). These products are intended to be secured
to the side of an adult bed for the purpose of having a baby sleep in close proximity to an adult.
1.4 No bedside sleeper produced after the approval date of this consumer safety specification shall, either by label or other means,
indicate compliance with the specification unless it complies with all of the requirements contained herein.
1.5 This consumer safety performance specification is not intended to address incidents and injuries resulting from alteration or
unreasonable abuse or misuse of the product by a child or child care provider.
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1
This consumer safety specification is under the jurisdiction of ASTM Committee F15 on Consumer Products and is the direct responsibility of Subcommittee F15.18
on Cribs, Toddler Beds, Play Yards, Bassinets, Cradles and Baby Changing Products.
Current edition approved Oct. 1, 2022Jan. 1, 2023. Published November 2022January 2023. Originally approved in 2011. Last previous edition approved in 20192022
as F2906 – 13 (2019).F2906 – 22. DOI: 10.1520/F2906-22.10.1520/F2906-23.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2906 − 23
1.7 The following precautionary caveat pertains only to the test method portion, Section 6 of this consumer safety performance
specification. This standard may involve the use of hazardous materials, operations and equipment. This standard does not purport
to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish
appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
F2085 Consumer Safety Specification for Portable Bed Rails
F2194 Consumer Safety Specification for Bassinets and Cradles
3. Terminology
3.1 Definitions:
3.1.1 attachment system, n—the means used to attach the bedside sleeper to the adult bed.
3.1.2 bedside sleeper, n—a rigid frame assembly that may be combined with a fabric or mesh assembl
...