ASTM B775-15
(Specification)Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe
Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe
ABSTRACT
This general specification contains the mandatory requirements to the ASTM standards listed herein for longitudinally welded piping made from nickel and nickel alloys. In case of conflict, the requirements listed in the particular product specification takes precedence over those listed here.
SCOPE
1.1 This specification contains various requirements that, with the exception of Section 5 and Section 10, are mandatory requirements to the following ASTM nickel and nickel alloy, longitudinally welded piping specifications:2
Title of Specification
ASTM
Designation2
Welded UNS N08020, N08024, and N08026 Alloy Pipe
B464/B464M
Welded Nickel-Iron-Chromium Alloy Pipe
B514
Welded Nickel-Chromium-Iron-Alloy (UNS N06600,
UNS N06603, UNS N06025 and UNS N06045) Pipe
B517
Welded Nickel and Nickel-Cobalt Alloy Pipe
B619/B619M
UNS N08904, UNS N08925, and UNS N08926 Welded Pipe
B673
UNS N08367 Welded Pipe
B675
Nickel-Alloy (UNS N06625, N06219, and N08825) Welded Pipe
B705
Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Welded Pipe
B723
Welded Nickel (UNS N02200/UNS N02201) and Nickel
Copper Alloy (UNS N04400) Pipe
B725
1.2 One or more of the test requirements of Section 5 apply only if specifically stated in the product specification or in the purchase order.
1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only the requirement of the product specification needs to be satisfied.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B775 −15
StandardSpecification for
General Requirements for Nickel and Nickel Alloy Welded
1
Pipe
This standard is issued under the fixed designation B775; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* with all hazards including those identified in the appropriate
Safety Data Sheet (SDS) for this product/material as provided
1.1 This specification contains various requirements that,
by the manufacturer, to establish appropriate safety and health
with the exception of Section 5 and Section 10, are mandatory
practices, and determine the applicability of regulatory limi-
requirements to the following ASTM nickel and nickel alloy,
2 tations prior to use.
longitudinally welded piping specifications:
ASTM
2 2. Referenced Documents
Title of Specification Designation
2
2.1 ASTM Standards:
Welded UNS N08020, N08024, and N08026 Alloy Pipe B464/B464M
Welded Nickel-Iron-Chromium Alloy Pipe B514 B168 Specification for Nickel-Chromium-IronAlloys (UNS
Welded Nickel-Chromium-Iron-Alloy (UNS N06600, B517
N06600, N06601, N06603, N06690, N06693, N06025,
UNS N06603, UNS N06025 and UNS N06045) Pipe
N06045, and N06696), Nickel-Chromium-Cobalt-
Welded Nickel and Nickel-Cobalt Alloy Pipe B619/B619M
UNS N08904, UNS N08925, and UNS N08926 Welded Pipe B673 Molybdenum Alloy (UNS N06617), and Nickel-Iron-
UNS N08367 Welded Pipe B675
Chromium-Tungsten Alloy (UNS N06674) Plate, Sheet,
Nickel-Alloy (UNS N06625, N06219, and N08825) Welded B705
and Strip
Pipe
Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Welded Pipe B723 B464/B464M Specification for Welded UNS N08020 Alloy
Welded Nickel (UNS N02200/UNS N02201) and Nickel B725
Pipe
Copper Alloy (UNS N04400) Pipe
B514 SpecificationforWeldedNickel-Iron-ChromiumAlloy
1.2 One or more of the test requirements of Section 5 apply
Pipe
only if specifically stated in the product specification or in the
B517 Specification for Welded Nickel-Chromium-Iron-
purchase order.
Alloy (UNS N06600, UNS N06603, UNS N06025, and
1.3 In case of conflict between a requirement of the product UNS N06045) Pipe
specification and a requirement of this general specification, B619/B619M Specification for Welded Nickel and Nickel-
only the requirement of the product specification needs to be Cobalt Alloy Pipe
satisfied. B673 Specification for UNS N08925, UNS N08354, and
UNS N08926 Welded Pipe
1.4 The values stated in inch-pound units are to be regarded
B675 Specification for UNS N08367 Welded Pipe
as standard. The values given in parentheses are mathematical
B705 SpecificationforNickel-Alloy(UNSN06625,N06219
conversions to SI units that are provided for information only
and N08825) Welded Pipe
and are not considered standard.
B723 Specification for Nickel-Chromium-Molybdenum-
1.5 This standard does not purport to address all of the
Cobalt-Tungsten-Iron-Silicon Alloy (UNS N06333)
safety concerns, if any, associated with its use. It is the
Welded Pipe
responsibility of the user of this standard to become familiar
B725 Specification for Welded Nickel (UNS N02200/UNS
N02201) and Nickel Copper Alloy (UNS N04400) Pipe
1
This specification is under the jurisdiction of ASTM Committee B02 on B880 Specification for General Requirements for Chemical
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
Check Analysis Limits for Nickel, Nickel Alloys and
B02.07 on Refined Nickel and Cobalt and Their Alloys.
Cobalt Alloys
Current edition approved Oct. 1, 2015. Published December 2015. Originally
E8 Test Methods for Tension Testing of Metallic Materials
approved in 1987. Last previous edition approved in 2013 as B775 – 13. DOI:
10.1520/B0775-15.
E18 Test Methods for Rockwell Hardness of Metallic Ma-
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
terials
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
E29 Practice for Using Significant Digits in Test Data to
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. Determine Conformance with Specifications
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B775−15
E39 Methods for Chemical Analysis of Nickel (Withdrawn 4.3 The product (check) analysis of the material shall meet
3
1995) the requirements for the ladle analysis within the tolerance
E76 Test Methods for Chemical Analysis of Nickel-Copper limits prescribed in Specification B880.
3
Alloys (Withdrawn 2003)
5. Test Requirements
E1
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B775 − 13 B775 − 15
Standard Specification for
General Requirements for Nickel and Nickel Alloy Welded
1
Pipe
This standard is issued under the fixed designation B775; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification contains various requirements that, with the exception of Section 5 and Section 10, are mandatory
2
requirements to the following ASTM nickel and nickel alloy, longitudinally welded piping specifications:
ASTM
2
Title of Specification Designation
Welded UNS N08020, N08024, and N08026 Alloy Pipe B464
Welded UNS N08020, N08024, and N08026 Alloy Pipe B464/B464M
Welded Nickel-Iron-Chromium Alloy Pipe B514
Welded Nickel-Chromium-Iron-Alloy (UNS N06600, B517
UNS N06603, UNS N06025 and UNS N06045) Pipe
Welded Nickel and Nickel-Cobalt Alloy Pipe B619
Welded Nickel and Nickel-Cobalt Alloy Pipe B619/B619M
UNS N08904, UNS N08925, and UNS N08926 Welded Pipe B673
UNS N08367 Welded Pipe B675
Nickel-Alloy (UNS N06625, N06219, and N08825) Welded B705
Pipe
Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Welded Pipe B723
Welded Nickel (UNS N02200/UNS N02201) and Nickel B725
Copper Alloy (UNS N04400) Pipe
1.2 One or more of the test requirements of Section 5 apply only if specifically stated in the product specification or in the
purchase order.
1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only
the requirement of the product specification needs to be satisfied.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data
Sheet (MSDS)(SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices,
and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
B168 Specification for Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045,
and N06696), Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617), and Nickel-Iron-Chromium-Tungsten Alloy
(UNS N06674) Plate, Sheet, and Strip
B464B464/B464M Specification for Welded UNS N08020 Alloy Pipe
B514 Specification for Welded Nickel-Iron-Chromium Alloy Pipe
B517 Specification for Welded Nickel-Chromium-Iron-Alloy (UNS N06600, UNS N06603, UNS N06025, and UNS N06045)
Pipe
1
This specification is under the jurisdiction of ASTM Committee B02 on Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee B02.07 on Refined
Nickel and Cobalt and Their Alloys.
Current edition approved Feb. 1, 2013Oct. 1, 2015. Published March 2013December 2015. Originally approved in 1987. Last previous edition approved in 20082013 as
B775 – 08.B775 – 13. DOI: 10.1520/B0775-13.10.1520/B0775-15.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’sstandard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B775 − 15
B619B619/B619M Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe
B673 Specification for UNS N08925, UNS N08354, and UNS N08926 Welded Pipe
B675 Specification for UNS N08367 Welded Pipe
B705 Specification for Nickel-Alloy (UNS N06625, N06219 and N08825) Welded Pipe
B723 Specification for Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon Alloy (UNS N06333) Welded Pipe
B725 Specification for Welded Nickel (UNS N02200/UNS N02201) and Nickel Copper Alloy (UNS N04400) Pipe
B880 Specification for General Requirements for Chemical Check Analysis Limits for Nickel, Nickel Alloys and Cobalt Alloys
E8 Test Methods for Tension Testing of Metallic Materials
E18 T
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.