iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D6551-00

(Practice)

Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Xenon-Arc Exposure Apparatus

Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Xenon-Arc Exposure Apparatus

SCOPE
1.1 This practice describes one enviroment for the exposure of pressure-sensitive tape, used primarily for packaging, to an accelerated weathering environment.
1.2 This practice describes sample preparation and the accelerated environment to which it shall be exposed. It does not specify the length of time of the exposure nor what tests shall be performed on the material following the exposure.
1.3 The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently without combining values in any way.  
1.4  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
09-May-2000
ICS
83.180 - Adhesives
Technical Committee
D10 - Packaging
Drafting Committee
D10.14 - Tape and Labels
Current Stage
Ref Project

Relations

Replaced By
ASTM D6551/D6551M-05 - Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Xenon-Arc Exposure Apparatus
Effective Date
01-Dec-2005

Buy Standard

ASTM D6551-00 - Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Xenon-Arc Exposure ApparatusASTM D6551-00 - Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Xenon-Arc Exposure Apparatus
PreviousNext
Standard
ASTM D6551-00 - Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Xenon-Arc Exposure Apparatus
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn. Contact ASTM
International (www.astm.org) for the latest information.
Designation:D6551–00
Standard Practice for
Accelerated Weathering of Pressure-Sensitive Tapes by
Xenon-Arc Exposure Apparatus
This standard is issued under the fixed designation D 6551; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope 3. Summary of Practice
1.1 This practice describes one environment for the expo- 3.1 The pressure-sensitive tape is exposed for the time
sureofpressure-sensitivetape,usedprimarilyforpackaging,to specified in accordance with the conditions provided in Prac-
an accelerated weathering environment. tice G 155. Following this exposure the specimen is ready for
1.2 This practice describes sample preparation and the a prescribed examination of physical characteristics by other
accelerated environment to which it shall be exposed. It does standards as determined by the applicable material specifica-
not specify the length of time of the exposure nor what tests tion or other document.
shall be performed on the material following the exposure.
4. Significance and Use
1.3 The values stated in either SI or inch-pound units are to
be regarded separately as standard. The values stated in each 4.1 This practice describes one method for accelerated
weathering of pressure-sensitive tapes used primarily for
system may not be exact equivalents; therefore, each system
must be used independently without combining values in any packaging. It is not intended for evaluation the weathering
characteristics of pressure-sensitive tapes used in long-term
way.
1.4 This standard does not purport to address all of the outdoor exposure conditions (see D 5105).
4.2 This practice does not necessarily provide direct simu-
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro- lation of natural exposure.
4.3 Results from use of this practice shall not be represented
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use. as being equivalent to those of any natural weathering test until
a satisfactory degree of correlation has been established for the
2. Referenced Documents
material in question.
2.1 ASTM Standards: 4.4 Variation in results are possible when operating condi-
A 666 Specification for Annealed or Cold-Worked Austen- tions vary within accepted limits for the instrument specified in
itic Steel, Sheet, Strip, Plate, and Flat Bar Practices G 151 and G 155.
D 3330/D 3330M Test Methods for Peal Adhesion of
3 5. Apparatus
Pressure-Sensitive Tape at 180° Angle
D 3715/D 3715M Practice for Quality Assurance of 5.1 Exposure Apparatus, a xenon-arc weathering apparatus
with daylight filters conforming to all parameters as described
Pressure-Sensitive Tapes
D 5105 Practice for Performing Accelerated Outdoor in Practices G 151 and G 155.
,
5 6
5.2 Panels , for holding or supporting specimens approxi-
Weathering of Pressure-Sensitive Tapes Using Concen-
trated Natural Sunlight mately 75 by 225 mm [3 by 9 in.] and rigid enough to resist
deformation during use.
G 151 Practice for Exposing Nonmetallic Materials in Ac-
celerated Test Devices that Use Laboratory Light Sources 5.2.1 ThematerialshallbeType302or304stainlesssteelin
accordance with Specification A 666 having a bright annealed
G 155 Practice for Operating Xenon-Arc Light Apparatus
for Exposure of Nonmetallic Materials finish. The surface roughness height shall be 50 6 5 mm [2.0
6 0.1 µ-in.] arithmetical average deviation from the mean line.
5.2.2 Other dimensions or materials and finishes are accept-
able when defined by the subsequent test standard or commod-
This practice is under the jurisdiction ofASTM Committee D10 on Packaging
ity specification.
and is the direct responsibility of Subcommittee D10.14 on Tapes and Labels.
Current edition approved May 10, 2000. Published July 2000.
Annual Book of ASTM Standards, Vol 01.03.
3 5
Annual Book of ASTM Standards, Vol 15.09. Chemsultants International, 9349 Hamilton Drive, Mentor, OH 44061–1118.
4 6
Annual Book of ASTM Standards, Vol 14.04. Panel Lab Products, 26200 First Street, Cleveland, OH 94145.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn. Contact ASTM
International (www.astm.org) for the latest information.
D6551
5.2.3 A panel or frame o
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D5749-24(Specification)
Standard Specification for Reinforced and Plain Gummed Tape for Sealing and Securing

ABSTRACT
This specification covers reinforced (Type I) and plain (Type II) paper gummed adhesive tapes used for securing and banding paper products and sealing fiberboard boxes. Type I gummed tape may be strippable (Class 1) or nonstrippable (Class 2), while Type II paper-backed gummed tape, whether Grade A (light duty), B (medium duty), or C (heavy duty), is nonstrippable. The tapes shall be manufactured from kraft paper, but the use of recycled pulp in the paper is encouraged as well, and the adhesive used must not have an offensive odor and shall conform to the environmental considerations specified. Type I tapes shall consist of two strips of paper in roll form, while Type II tapes shall consist of one strip of paper in roll form. Upon manufacture, the tape shall be clean and free of folds, sharp creases, tears, cuts, and holes. The tapes shall be examined for visual defects, defects in roll construction, and defects in dimensions. Tests for adhesiveness, tensile strength, and elongation shall be performed as well, and shall conform to the physical properties specified.
SCOPE
1.1 This specification covers plain and reinforced paper gummed adhesive tapes suitable for securing and banding paper products and closing fiberboard boxes.  
1.2 This specification is intended to replace Fed. Specs. CID A-A-1492, CID A-A-1671, and PPP-T-45 in part.  
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 11, of this specification:   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM D6788-24(Specification)
Standard Specification for Repositionable Pressure-Sensitive Flags

ABSTRACT
This specification covers repositionable pressure-sensitive flags used to mark, flag, and index documents, books, periodicals, and so forth. Flags covered here consist of a single sheet of matte film partially covered by adhesive. A non-adhesive tab or section at one end of the flag serves for easy removal from most surfaces, including paper. The backing shall consist of polyester, polypropylene, or polyethylene film, and shall have a transparent matte surface on one side that is writable by pens and pencils. Flags are available in the following types: Type 1, which are of specified width, and have a colored tab at one end; Type 2, which are of the same width as Type 1, and have a printed message on the top side of the flag; Type 3, which twice the width of Type 1, and have a white tab at one end to highlight writing; Type 4, which are half the width of Type 1, and have a colored tab at one end; and Type 5, which are half the width of Type 1, and have an arrow or a message printed on the top side of the flag. Sampled specimens shall conform to physical requirements in terms of minimum and maximum adhesion, dispension force, and thickness.
SCOPE
1.1 This specification covers repositionable pressure-sensitive flags used to mark, flag, and index documents, books, periodicals, and so forth.  
1.2 The values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently, without combining values in any way.  
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 14, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6195-22(Test Method)
Standard Test Methods for Loop Tack

SIGNIFICANCE AND USE
5.1 These test methods provide a quantitative measure of the pressure-sensitive tack property of an adhesive.
FIG. 1 Loop Tack Test Fixture 1  
FIG. 2 Loop Tack Test Fixture 2  
FIG. 3 Loop Tack Sample During Test  
5.2 These test methods are designed to measure the tack property of the adhesive mass. The tack of a given adhesive varies depending on the backing (generally, stiffer backings lead to higher values).  
5.3 Theses test methods are suitable for quality control and research purposes.  
5.4 Test Method A (using Tensile Tester) makes use of a specimen strip 7 in. (175 mm) in length. Both the FINAT FTM 9 “Quick Stick” Tack Measurement Test and the TLMI L-IB2 Tensile Tester Loop Tack Test also use a specimen strip of that length.  
5.5 Test Method B (using Loop Tack Tester) makes use of a specimen strip five in. (125 mm) in length. That is the only length specimen strip that fits properly in the loop tack tester.  
5.6 If the adhesive is not already otherwise coated, these test methods incorporate the use of a clear 2 mil (0.05 mm) polyester (PET) film backing for specimen preparation. Use of other backing materials changes performance of the specimen to be tested.
SCOPE
1.1 These test methods cover the determination of properties of a pressure-sensitive adhesive. These test methods are applicable to those adhesives that form a bond of measurable strength rapidly upon contact with another surface. Tack force may be measured as the force required to separate the adhesive from the adherend at the interface shortly after they have been brought into contact under a load equal only to the weight of the pressure-sensitive article (for example, tape, label, sticker, etc.) on a 1 in.2 contact area.  
1.2 The following test methods are included:  
1.2.1 Test Method A (using Tensile Tester), and  
1.2.2 Test Method B (using Loop Tack Tester).  
1.3 The values stated in inch-pound units are to be regarded as the standard because the industry standard width for pressure-sensitive tape is 1 inch. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D5570/D5570M-10(2022)(Test Method)
Standard Test Method for Water Resistance of Tape and Adhesives Used as Box Closure

SIGNIFICANCE AND USE
5.1 When a box becomes wet, the performance of the box and its closure are reduced. It is desirable to have box closure methods that retain an ability to keep the box closed when wet. Sealing or reinforcing methods sometimes are useful to improve performance of wet boxes and closures. Water resistance is sometimes a regulatory or contractual requirement.  
5.2 A test result indicating that a box closure tape or adhesive is soluble or dispersible in water is an indication that its function will be significantly impaired when wet. A test result that does not indicate solubility or dispersibility does not necessarily ensure that the bonding ability will be satisfactory when wet or that the performance of the box closure will be satisfactory when wet. Package performance testing described in the water resistance section of Practice D1974 is useful to further investigate the effects of water on package and closure functions.
SCOPE
1.1 This test method covers a procedure to determine the water resistance of an adhesive or tape as measured by the amount of tape or adhesive dissolved or dispersed in water.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3811/D3811M-21a(Test Method)
Standard Test Method for Unwind Force of Pressure-Sensitive Tapes

SIGNIFICANCE AND USE
5.1 This procedure simulates hand and machine unwinding of tape at low rates. The force required for unwinding at low rates is a function of rate. At some rate (expected to be different for each construction type and manufacturer) there occurs an inversion of the response. The rate for this test method does not allow for comparisons of different tapes that will be unwound at high rates.  
5.2 This procedure can be used to indicate satisfaction where a specification for unwind; either maximum, minimum, or mean; is established and when the responses referred to in 5.1 are taken into consideration.
SCOPE
1.1 This test method covers one procedure for determining the force required to unwind a roll of pressure-sensitive tape.  
1.2 The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently, without combining values in any way.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6463/D6463M-06(2020)(Test Method)
Standard Test Method for Time to Failure of Pressure Sensitive Articles Under Sustained Shear Loading

SIGNIFICANCE AND USE
5.1 This test method measures the cohesive strength of the adhesive on a pressure sensitive article. The time to failure can predict end use properties of pressure sensitive articles such as edge ooze from cold flow; trimming, slitting and die cutting quality; telescoping in tapes; ability to seal packages; and vertical holding power.  
5.2 This test method is suitable for quality control, development and applications testing.  
5.3 If the adhesive is not already coated, the adhesive can be coated on smooth, clear polyester (PET) film backing 0.05 mm [0.002 in.] thick. The recommended dry adhesive thickness is 0.025 mm [0.001 in.].  
5.4 Humidity has a strong effect on time to failure for many pressure sensitive articles. Therefore, humidity should be controlled in accordance with 8.1.2.
SCOPE
1.1 This test method covers the ability of a pressure sensitive article (for example, tape, label, sticker, etc.) to remain adhered to a stainless steel panel under a constant load applied parallel to the bonding surface of the pressure sensitive article.  
1.2 Values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents, therefore, each system must be used independently without combining values in any way.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D3652/D3652M-01(2020)(Test Method)
Standard Test Method for Thickness of Pressure-Sensitive Tapes

SIGNIFICANCE AND USE
4.1 Thickness is an important property of tapes, and this dimension is important for certain end uses. This test method is useful for quality control and for acceptance testing for conformance to specifications.
SCOPE
1.1 This test method covers the determination of the thickness of pressure-sensitive tapes at standard conditions.  
1.2 This test method is intended to replace AFERA 40062 and PSTC 33.2  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D3813/D3813M-98(2020)(Test Method)
Standard Test Method for Curling, Twisting, and Tubing on Unwind of Pressure-Sensitive Tapes

SIGNIFICANCE AND USE
5.1 This test method will provide information on the relative tendency of tapes to curl, twist, or form into a tube with touching edges. The amount of each is a predictor of the difficulty one might experience in handling strips of tape of any length during their application.  
5.2 There are several causes for variation in the extent or degree of these characteristics and may vary themselves within a production lot of tape. Therefore, it is essential to use an accepted sampling plan (see Section 7) when it is desired to use this test method to compare two types of tape for acceptance sampling purposes.
SCOPE
1.1 This test method provides one procedure for determining the extent of curling, the degree of twisting, and tendency to form a tube resulting from unwinding of the tape from its roll.  
1.2 The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently, without combining values in any way.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D5486/D5486M-06(2020)(Specification)
Standard Specification for Pressure-Sensitive Tape for Packaging, Box Closure, and Sealing

ABSTRACT
This specification covers pressure-sensitive tapes of film, paper, and cloth types, with applications in packaging, box closure, and sealing. Covered in this specification are five types of tape: waterproof, weather-resistant, polyester-backed tape (Type I), water-resistant polyester-backed tape (Type II), water-resistant polypropylene-backed tape (Type III), water-resistant woven-cloth-backed tape (Type IV), and weather-resistant paper-backed tape. The tape shall be manufactured with film, paper, or cloth backing, coated with a smooth and uniformly distributed layer of pressure-sensitive water-insoluble adhesive. The tape shall be in wound into rolls on cores of paper fiber or plastic and shall be free from defects, with the edges clean, straight, and unbroken. Tests for adhesion, break strength, tear resistance, thickness, water-penetration rate, water solubility, water-vapor transmission rate, and weathering shall be performed and shall conform to the requirements specified.
SCOPE
1.1 This specification covers film, paper, and cloth pressure-sensitive tapes used for box closure and sealing.  
1.2 The values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently, without combining values in any way.  
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 14, of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM D5750/D5750M-95(2020)(Guide)
Standard Guide for Width and Length of Pressure-Sensitive Tape

SIGNIFICANCE AND USE
4.1 Conformance to this guide will reduce chances of misunderstanding between suppliers and users of pressure-sensitive tapes.  
4.2 It is recommended that this guide be referenced where widths and lengths of pressure-sensitive tapes are stated, such as in contracts, orders, advertisements, and labeling.
SCOPE
1.1 This guide provides guidelines for widths and lengths of pressure-sensitive tape, including tolerances and labeling in the inch-pound and SI systems. It is not intended for tapes used for medical, surgical, or label stock purposes.  
1.2 Units stated in the inch-pound system followed by a calculated unit in the SI system are to be regarded separately as standard and should not be interchangeable with units stated in the SI system. The units stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    2 pages
    English language
    sale 15% off