ASTM A835/A835M-84(2010)

Standard Specification for Sizes of Ferroalloys and Alloy Additives

ABSTRACT
This specification covers standards for sizes of screened ferroalloys and alloy additives. Products shall conform to specified nominal size, standard ordered size, maximum allowable oversize, maximum allowable undersize, and friability rating. Description of the friability ratings of the ferroalloys is also provided.
SCOPE
1.1 This specification covers standard nominal sizes and size tolerances of screened ferroalloy and alloy additive products. This specification provides a range of sizes as referenced in all ASTM specifications for ferroalloys and alloy additives.
1.2 The sizes and tolerances allow for varying degrees of friability upon receipt of material since some attrition may be expected in transit, storage, and handling.
1.3 Specifications of sieve sizes used to define tolerances are listed in Specification E11. Representative procedures for evaluation of each lot are described in Methods A610. Refer to Appendix X1 for applicable sieve designations (see Table X1.1).

General Information

• Status: Historical
• Publication Date: 31-Mar-2010
• ICS: 77.100 - Ferroalloys
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.18 - Castings

Relations

• Replaces: ASTM A835/A835M-84(2005) - Standard Specification for Sizes of Ferroalloys and Alloy Additives
• Effective Date: 01-Apr-2010
• Replaced By: ASTM A835/A835M-10 - Standard Specification for Sizes of Ferroalloys and Alloy Additives
• Effective Date: 01-Oct-2010

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A835/A835M – 84 (Reapproved 2010)
Standard Specification for
1
Sizes of Ferroalloys and Alloy Additives
This standard is issued under the fixed designationA835/A835M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
A
TABLE 1 Requirements for Screened Products
1. Scope
Nominal Standard Maximum Allowable Maximum Allowable Friability
1.1 This specification covers standard nominal sizes and
Size, in. Ordered Oversize Undersize Rating
size tolerances of screened ferroalloy and alloy additive
Size, Code
B C
Size Percent Size Percent
products. This specification provides a range of sizes as in. No.
referenced in allASTM specifications for ferroalloys and alloy Lump to Crushed Sizes:
6 8 by 4 to 10 in. 10 % through 4 in. 10 % 1–6
additives.
5 8 by 2 to 10 in. 10 % through 2 in. 10 % 1–6
1.2 The sizes and tolerances allow for varying degrees of
4 6 by 2 to 8 in. 10 % through 2 in. 10 % 1–6
1
friability upon receipt of material since some attrition may be
3 ⁄2 5 by 2 to 7 in. 10 % through 2 in. 10 % 1–6
3 (A) 5 by 1 to 7 in. 10 % through 1 in. 10 % 1–6
expected in transit, storage, and handling.
3 (B) 4 by 2 to 6 in. 10 % through 2 in. 10 % 1–6
1.3 Specifications of sieve sizes used to define tolerances
1
2 ⁄2 4 by 1 to 6 in. 10 % through 1 in. 10 % 1–6
1 1 1
are listed in Specification E11. Representative procedures for 2 ⁄4 4by ⁄2 to 5 in. 10 % through ⁄2 in. 10 % 1–6
2 3 by 1 to 4 in. 10 % through 1 in. 10 % 1–6
evaluation of each lot are described in MethodsA610. Refer to
1 1 1
1 ⁄2 3by ⁄2 to 4 in. 10 % through ⁄2 in. 10 % 1–6
Appendix X1 for applicable sieve designations (see Table
1 1 1
1 ⁄4 2by ⁄2 to 3 in. 10 % through ⁄2 in. 10 % 1–6
1 1 1
X1.1). 1 ⁄8 2by ⁄4 to 3 in. 10 % through ⁄4 in. 10 % 1–6
Small Crushed Sizes by Down:
1
2 4 by D to 5 in. 10 % through ⁄2 in. 15 % 1–6
2. Referenced Documents
1 1
1 ⁄2 3 by D to 4 in. 10 % through ⁄8 in. 15 % 1–6
2
1
2.1 ASTM Standards: 1 2 by D to 3 in. 10 % through ⁄8 in. 15 % 1–4
to 3 in. 8 % through No. 8 20 % 5,6
A610 Test Methods for Sampling and Testing Ferroalloys
1 1
⁄2 1byD to 1 ⁄2 in. 10 % through No. 16 15 % 1–4
for Determination of Size
1
to 1 ⁄2 in. 8 % through No. 20 15 % 5,6
1 1 3
E11 Specification forWovenWireTest Sieve Cloth andTest ⁄4 ⁄2 by D to ⁄4 in. 10 % through No. 20 15 % 1–4
3
to ⁄4 in. 8 % through No. 70 20 % 5,6
Sieves
A
1
For screened products below ⁄2 in. by down-crushed sizes, size tolerances
3. Dimensional Requirements
should be agreed upon between manufacturer and purchaser.
B
3.1 Screened products shall conform to the sizes given in
1 in. = 25.4 mm.
C
See Appendix X2 for description of rating code.
Table 1.
3.1.1 The sizes listed in Table 1 are typical as shipped from
the manufacturer’s plant. Ferroalloys exhibit varying degrees
of friability; therefore, some attrition may be expected in
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
transit, storage, and handling. A quantitative test is not avail-
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
able for rating relative friability of ferroalloys. A code system
A01.18 on Castings.
has been developed, therefore, for this purpose, and a number
Current edition approved April 1, 2010. Published May 2010. Originally
approved
...