ASTM C1791-15
(Guide)Standard Guide for Reduction of Efflorescence Potential in New Unit Pavement Systems
Standard Guide for Reduction of Efflorescence Potential in New Unit Pavement Systems
SIGNIFICANCE AND USE
4.1 This guide provides information that, if implemented, will reduce efflorescence potential in new unit pavement systems. However, its implementation will not always completely prevent efflorescence.
4.2 This guide may be augmented by related information contained in the appendixes of Specification C270, the additional material listed in Appendix X1 in this standard, and other publications.
SCOPE
1.1 This guide covers methods for reducing efflorescence potential in new unit pavement systems.
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1791 − 15
StandardGuide for
Reduction of Efflorescence Potential in New Unit Pavement
1
Systems
This standard is issued under the fixed designation C1791; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* pounds in clay masonry are usually yellow or green; and stains
produced by acid-soluble manganese compounds are usually
1.1 This guide covers methods for reducing efflorescence
brown or gray.
potential in new unit pavement systems.
3.2.3 jointing material, n—mortar, aggregate, sealant, or
1.2 The values stated in inch-pound units are to be regarded
other materials used between paver units.
as the standard. The SI units given in parentheses are for
3.2.4 unit pavement system, n—a system consisting of edge
information only.
restraint, wearing course of discrete clay or concrete pavers,
1.3 This standard does not purport to address all of the
setting bed, jointing material, base or sub-base, or combination
safety concerns, if any, associated with its use. It is the
thereof, and appropriate drainage elements.
responsibility of the user of this standard to establish appro-
3.2.4.1 Discussion—Flexible pavement is a unit pavement
priate safety and health practices and determine the applica-
system whose wearing course consists of discrete clay or
bility of regulatory limitations prior to use.
concrete pavers on an aggregate base, an aggregate base
stabilized with asphalt or cement, or asphalt pavement.
2. Referenced Documents
3.2.4.2 Discussion—Rigid pavement is a unit pavement
2.1 ASTM Standards:
system whose surface wearing course consists of discrete clay
C67 Test Methods for Sampling and Testing Brick and
or concrete units on a rigid base such as concrete.
Structural Clay Tile
C270 Specification for Mortar for Unit Masonry
4. Significance and Use
C1180 Terminology of Mortar and Grout for Unit Masonry
4.1 This guide provides information that, if implemented,
C1232 Terminology of Masonry
will reduce efflorescence potential in new unit pavement
systems. However, its implementation will not always com-
3. Terminology
pletely prevent efflorescence.
3.1 Definitions:
4.2 This guide may be augmented by related information
3.1.1 Terminology defined in Terminologies C1180 and
contained in the appendixes of Specification C270, the addi-
C1232 shall apply in this guide.
tional material listed in Appendix X1 in this standard, and
3.2 Definitions of Terms Specific to This Standard:
other publications.
3.2.1 cryptoflorescence, n—a crystalline deposit of water-
soluble compounds in the pores of unit pavement system
5. Principles of Efflorescence
materials.
5.1 Efflorescence is directly related to the quantity of
3.2.2 efflorescence, n—a crystalline deposit, usually white,
water-soluble compounds within, or exposed to, a unit pave-
of water-soluble compounds on the surface of a unit pavement
ment system; and to the quantity of water exposed to these
system.
compounds. Water-soluble compounds or water causing efflo-
3.2.2.1 Discussion—While not considered to be
rescence may be from adjacent surfaces or beneath the pave-
efflorescence, stains produced by acid-soluble vanadium com-
ment system: for example, fertilizer in runoff from adjacent
flower beds or lawns; ground water evaporating through the
wearing course; and water from sprinkler systems and roofs.
1
Since neither water nor water-soluble compounds can be
This test method is under the jurisdiction of ASTM Committee C15 on
Manufactured Masonry Units and is the direct responsibility of Subcommittee
completely eliminated from unit pavement systems, the poten-
C15.05 on Masonry Assemblies.
tial for efflorescence is reduced by reducing water-soluble
Current edition approved July 1, 2015. Published July 2015. Originally approved
compounds and water retained within the unit pavement
in 2014. Last previous edition approved in 2014 as C1791 –14a. DOI: 10.1520/
C1791-15. system.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1791 − 15
5.2 Water can penetrate through joints in the surface of unit 6.2.4 Properly sized and located movement joints in the
pavementsystems.Itcanpenetratevoidsinthemortarjointsor pavement and in rigid bases such as concrete.
the interface between the paver unit and jointing material. 6.2.5 Gutters, overhangs, and canopies to protect the pave-
ment from rain.
5.3 If a significant amount of water penetrates a unit
6.2.6 Utilization of compatibl
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1791 − 14a C1791 − 15
Standard Guide for
Reduction of Efflorescence Potential in New Unit Pavement
1
Systems
This standard is issued under the fixed designation C1791; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This guide covers methods for reducing efflorescence potential in new unit pavement systems.
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for
information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2.1 ASTM Standards:
C67 Test Methods for Sampling and Testing Brick and Structural Clay Tile
C270 Specification for Mortar for Unit Masonry
C1180 Terminology of Mortar and Grout for Unit Masonry
C1232 Terminology of Masonry
3. Terminology
3.1 Definitions:
3.1.1 Terminology defined in Terminologies C1180 and C1232 shall apply in this guide.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 cryptoflorescence, n—a crystalline deposit of water-soluble compounds in the pores of unit pavement system materials.
3.2.2 efflorescence, n—a crystalline deposit, usually white, of water-soluble compounds on the surface of a unit pavement
system.
1
This test method is under the jurisdiction of ASTM Committee C15 on Manufactured Masonry Units and is the direct responsibility of Subcommittee C15.05 on Masonry
Assemblies.
Current edition approved Dec. 1, 2014July 1, 2015. Published December 2014July 2015. Originally approved in 2014. Last previous edition approved in 2014 as C1791
–14.–14a. DOI: 10.1520/C1791-14A.10.1520/C1791-15.
3.2.2.1 Discussion—
While not considered to be efflorescence, stains produced by acid-soluble vanadium compounds in clay masonry are usually yellow
or green; and stains produced by acid-soluble manganese compounds are usually brown or gray.
3.2.3 jointing material, n—mortar, aggregate, sealant, or other materials used between paver units.
3.2.4 unit pavement system, n—a system consisting of edge restraint, wearing course of discrete clay or concrete pavers, setting
bed, jointing material, base or sub-base, or combination thereof, and appropriate drainage elements.
3.2.4.1 Discussion—
Flexible pavement is a unit pavement system whose wearing course consists of discrete clay or concrete pavers on an aggregate
base, an aggregate base stabilized with asphalt or cement, or asphalt pavement.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1791 − 15
3.2.4.2 Discussion—
Rigid pavement is a unit pavement system whose surface wearing course consists of discrete clay or concrete units on a rigid base
such as concrete.
4. Significance and Use
4.1 This guide provides information that, if implemented, will reduce efflorescence potential in new unit pavement systems.
However, its implementation will not always completely prevent efflorescence.
4.2 This guide may be augmented by related information contained in the appendixes of Specification C270, the additional
material listed in Appendix X1 in this standard, and other publications.
5. Principles of Efflorescence
5.1 Efflorescence is directly related to the quantity of water-soluble compounds within, or exposed to, a unit pavement system;
and to the quantity of water exposed to these compounds. Water-soluble compounds or water causing efflorescence may be from
adjacent surfaces or beneath the pavement system: for example, fertilizer in runoff from adjacent flower beds or lawns; ground
water evaporating through the wearing course; and water from sprinkler systems and roofs. Since neither water nor water-soluble
compounds can be completely eliminated from unit pavement systems, the potential for efflorescence is reduced by reducing
water-soluble compounds and water retained within the unit pavement system.
5.2 Water can penetrate through joints in the surface of unit pavement systems. It can penetrate voids in the mortar
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.