ASTM A671/A671M-13e1

Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures

ABSTRACT
This specification covers standard requirements for electric-fusion-welded steel pipe with filler metal added, for atmospheric and lower temperatures. The steel pipe shall be fabricated from a pressure vessel quality plate of several analysis and strength levels. Several grades and classes of pipe shall be provided. Grade shall designate the type of plate used while class shall designate the type of heat treatment performed during pipe manufacture. Class shall be designated as to whether the weld is radiographically examined, and as to whether the pipe is pressure tested. Steel samples shall undergo tension and transverse guided weld bend tests and conform to the specified mechanical requirements.
SCOPE
1.1 This specification2 covers electric-fusion-welded steel pipe with filler metal added, fabricated from pressure vessel quality plate of several analyses and strength levels and suitable for high-pressure service at atmospheric and lower temperatures. Heat treatment may or may not be required to attain the desired properties or to comply with applicable code requirements. Supplementary requirements are provided for use when additional testing or examination is desired.  
1.2 The specification nominally covers pipe 16 in. [400 mm] in outside diameter or larger and of 1/4 in. [6 mm] wall thickness or greater. Pipe having other dimensions may be furnished provided it complies with all other requirements of this specification.  
1.3 Several grades and classes of pipe are provided.  
1.3.1 Grade designates the type of plate used as listed in 5.1.  
1.3.2 Class designates the type of heat treatment performed during manufacture of the pipe, whether the weld is radiographically examined, and whether the pipe has been pressure tested as listed in 1.3.3.  
1.3.3 Class designations are as follows (Note 1):    
Class  
Heat Treatment on Pipe  
Radiography, see Section  
Pressure Test, see:  
10  
none  
none  
none  
11  
none  
9  
none  
12  
none  
9  
8.3  
13  
none  
none  
8.3  
20  
stress relieved, see 5.3.1  
none  
none  
21  
stress relieved, see 5.3.1  
9  
none  
22  
stress relieved, see 5.3.1  
9  
8.3  
23  
stress relieved, see 5.3.1  
none  
8.3  
30  
normalized, see 5.3.2  
none  
none  
31  
normalized, see 5.3.2  
9  
none  
32  
normalized, see 5.3.2  
9  
8.3  
33  
normalized, see 5.3.2  
none  
8.3  
40  
normalized and tempered, see 5.3.3  
none  
none    
41  
normalized and tempered, see 5.3.3  
9  
none  
42  
normalized and tempered, see 5.3.3  
9  
8.3  
43  
normalized and tempered, see 5.3.3  
none  
8.3    
50  
quenched and tempered, see 5.3.4  
none  
none  
51  
quenched and tempered, see 5.3.4  
9  
none  
52  
quenched and tempered, see 5.3.4  
9  
8.3    
53  
quenched and tempered, see 5.3.4  
none  
8.3  
70  
quenched and precipitation heat treated  
none  
none    
71  
quenched and precipitation heat treated  
9  
none    
72  
quenched and precipitation heat treated  
9  
8.3    
73  
quenched and precipitation heat treated  
none  
8.3  
Note 1—Selection of materials should be made with attention to temperature of service. For such guidance, Specification A20/A20M may be consulted.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.

General Information

• Status: Historical
• Publication Date: 30-Sep-2013
• ICS: 23.040.10 - Iron and steel pipes
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.09 - Carbon Steel Tubular Products

Relations

• Replaces: ASTM A671/A671M-13 - Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures
• Effective Date: 01-Oct-2013
• Replaced By: ASTM A671/A671M-14 - Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures
• Effective Date: 01-Mar-2014
• Referred By: ASTM A530/A530M-18 - Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe
• Effective Date: 01-Oct-2013
• Referred By: ASTM A333/A333M-18 - Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature Service and Other Applications with Required Notch Toughness
• Effective Date: 01-Oct-2013

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation:A671/A671M −13
StandardSpecification for
Electric-Fusion-Welded Steel Pipe for Atmospheric and
1
Lower Temperatures
This standard is issued under the fixed designationA671/A671M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Editorially corrected reference in 8.3 in February 2014.
1. Scope*
33 normalized, see 5.3.2 none 8.3
40 normalized and tempered, see 5.3.3 none none
2
1.1 This specification covers electric-fusion-welded steel
41 normalized and tempered, see 5.3.3 9 none
pipe with filler metal added, fabricated from pressure vessel 42 normalized and tempered, see 5.3.3 9 8.3
43 normalized and tempered, see 5.3.3 none 8.3
quality plate of several analyses and strength levels and
50 quenched and tempered, see 5.3.4 none none
suitable for high-pressure service at atmospheric and lower
51 quenched and tempered, see 5.3.4 9 none
temperatures. Heat treatment may or may not be required to 52 quenched and tempered, see 5.3.4 9 8.3
53 quenched and tempered, see 5.3.4 none 8.3
attain the desired properties or to comply with applicable code
70 quenched and precipitation heat none none
requirements. Supplementary requirements are provided for
treated
71 quenched and precipitation heat 9 none
use when additional testing or examination is desired.
treated
1.2 The specification nominally covers pipe 16 in. [400
72 quenched and precipitation heat98.3
1
treated
mm] in outside diameter or larger and of ⁄4 in. [6 mm] wall
73 quenched and precipitation heat none 8.3
thickness or greater. Pipe having other dimensions may be
treated
furnished provided it complies with all other requirements of
NOTE 1—Selection of materials should be made with attention to
this specification.
temperature of service. For such guidance, Specification A20/A20M may
be consulted.
1.3 Several grades and classes of pipe are provided.
1.3.1 Gradedesignatesthetypeofplateusedaslistedin5.1.
1.4 The values stated in either SI units or inch-pound units
1.3.2 Class designates the type of heat treatment performed
are to be regarded separately as standard. Within the text, the
during manufacture of the pipe, whether the weld is radio-
SI units are shown in brackets. The values stated in each
graphically examined, and whether the pipe has been pressure
system may not be exact equivalents; therefore, each system
tested as listed in 1.3.3.
shall be used independently of the other. Combining values
1.3.3 Class designations are as follows (Note 1):
from the two systems may result in non-conformance with the
Class Heat Treatment on Pipe Radiography, Pressure Test, standard. The inch-pound units shall apply unless the “M”
see Section see:
designation of this specification is specified in the order.
10 none none none
11 none 9 none 2. Referenced Documents
12 none 98.3
3
2.1 ASTM Standards:
13 none none 8.3
20 stress relieved, see 5.3.1 none none
A20/A20MSpecificationforGeneralRequirementsforSteel
21 stress relieved, see 5.3.1 9 none
Plates for Pressure Vessels
22 stress relieved, see 5.3.1 9 8.3
A370Test Methods and Definitions for Mechanical Testing
23 stress relieved, see 5.3.1 none 8.3
30 normalized, see 5.3.2 none none
of Steel Products
31 normalized, see 5.3.2 9 none
A435/A435MSpecification for Straight-Beam Ultrasonic
32 normalized, see 5.3.2 9 8.3
Examination of Steel Plates
A530/A530MSpecification for General Requirements for
1 Specialized Carbon and Alloy Steel Pipe
This specification is under the jurisdiction ofASTM Committee A01 on Steel,
Stainless Steel and RelatedAlloys and is the direct responsibility of Subcommittee
A01.09 on Carbon Steel Tubular Products.
Current edition approved Oct. 1, 2013. Published October 2013. Originally
3
approved in 1972. Last previous edition approved in 2010 as A671–10. DOI: For referenced ASTM standards, visit the ASTM website, www.astm.org, or
10.1520/A0671_A0671M-13E01 contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi- Standards volume information, refer to the standard’s Document Summary page on
cation SA-671 in Section II of that Code. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
´1
A671/A671M−13
A577/A577MSpecification for Ultrasonic Angle-Beam Ex- 4.1.6 Length (specific or random),
amination of Steel Plates 4.1.7 End finish (11.4),
A578/A578MSpecification for Straight-Beam Ultrasonic 4.1.8 P
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: A671/A671M − 13 A671/A671M − 13
Standard Specification for
Electric-Fusion-Welded Steel Pipe for Atmospheric and
1
Lower Temperatures
This standard is issued under the fixed designation A671/A671M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Editorially corrected reference in 8.3 in February 2014.
1. Scope*
2
1.1 This specification covers electric-fusion-welded steel pipe with filler metal added, fabricated from pressure vessel quality
plate of several analyses and strength levels and suitable for high-pressure service at atmospheric and lower temperatures. Heat
treatment may or may not be required to attain the desired properties or to comply with applicable code requirements.
Supplementary requirements are provided for use when additional testing or examination is desired.
1
1.2 The specification nominally covers pipe 16 in. [400 mm] in outside diameter or larger and of ⁄4 in. [6 mm] wall thickness
or greater. Pipe having other dimensions may be furnished provided it complies with all other requirements of this specification.
1.3 Several grades and classes of pipe are provided.
1.3.1 Grade designates the type of plate used as listed in 5.1.
1.3.2 Class designates the type of heat treatment performed during manufacture of the pipe, whether the weld is radiographically
examined, and whether the pipe has been pressure tested as listed in 1.3.3.
1.3.3 Class designations are as follows (Note 1):
Class Heat Treatment on Pipe Radiography, Pressure Test,
see Section see:
10 none none none
11 none 9 none
12 none 9 8.3
13 none none 8.3
20 stress relieved, see 5.3.1 none none
21 stress relieved, see 5.3.1 9 none
22 stress relieved, see 5.3.1 9 8.3
23 stress relieved, see 5.3.1 none 8.3
30 normalized, see 5.3.2 none none
31 normalized, see 5.3.2 9 none
32 normalized, see 5.3.2 9 8.3
33 normalized, see 5.3.2 none 8.3
40 normalized and tempered, see 5.3.3 none none
41 normalized and tempered, see 5.3.3 9 none
42 normalized and tempered, see 5.3.3 9 8.3
43 normalized and tempered, see 5.3.3 none 8.3
50 quenched and tempered, see 5.3.4 none none
51 quenched and tempered, see 5.3.4 9 none
52 quenched and tempered, see 5.3.4 9 8.3
53 quenched and tempered, see 5.3.4 none 8.3
70 quenched and precipitation heat none none
treated
71 quenched and precipitation heat 9 none
treated
72 quenched and precipitation heat 9 8.3
treated
73 quenched and precipitation heat none 8.3
treated
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.09
on Carbon Steel Tubular Products.
Current edition approved Oct. 1, 2013. Published October 2013. Originally approved in 1972. Last previous edition approved in 2010 as A671–10. DOI:
10.1520/A0671_A0671M-13.10.1520/A0671_A0671M-13E01
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SA-671 in Section II of that Code.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
´1
A671/A671M − 13
NOTE 1—Selection of materials should be made with attention to temperature of service. For such guidance, Specification A20/A20M may be
consulted.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units
are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used
independently of the other. Combining values from the two systems may result in non-conformance with the standard. The
inch-pound units shall apply unless the “M” designation of this specification is specified in the order.
2. Referenced Documents
3
2.1 ASTM Standards:
A20/A20M Specification for General Requirements for Steel Plates for Pressure Vessels
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A435/A435M Specification for Straight-Beam Ultrasonic Examination of Steel Plates
A530/A530M Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe
A577/A577M Specification for Ultrasonic Angle-Beam Examination of Steel Plates
A578/A578M Specifi
...