ASTM A530/A530M-18
(Specification)Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe
Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe
ABSTRACT
This specification covers a general requirements for specialized carbon and alloy steel pipe. Tensile tests, tension tests, flattening tests, hydrostatic tests and ultrasonic tests shall be made to conform to the requirements specified. If the mechanical results do not conform to the requirements specified, retests shall be made. Defects in seamless pipe shall be repaired by welding.
SCOPE
1.1 This specification2 covers a group of requirements which, with the exceptions of Section 6.3, Section 14, Section 21, and Section 22, are mandatory requirements to the ASTM pipe product specifications noted below unless the product specification specifies different requirements, in which case the requirement of the product specification shall prevail.
1.2 Sections 6.3 or 21 are mandatory if the product specification has a requirement for product analysis or flattening tests.
1.3 Section 22 is mandatory if the product specification has a hydrostatic test requirement without defining the test parameters.
1.4 Section 14 is for information only.
1.5 In case of conflict between a requirement of the product specification and a requirement of this general requirement specification, only the requirement of the product specification need be satisfied.
Title of Specification
ASTM DesignationA
Seamless Carbon Steel Pipe for High-Temperature Service
A106/A106M
Metal-Arc-Welded Steel Pipe for Use With High-Pressure
Transmission Systems
A381
Seamless Carbon Steel Pipe for Atmospheric and Lower
Temperatures
A524
Centrifugally Cast Carbon Steel Pipe for High-Temperature
Service
A660/A660M
Electric-Fusion-Welded Steel Pipe for Atmospheric and
Lower Temperatures
A671/A671M
Electric-Fusion-Welded Steel Pipe for High-Pressure Service
at Moderate Temperatures
A672/A672M
Carbon and Alloy Steel Pipe, Electric-Fusion-Welded for
High-Pressure Service at High Temperatures
A691/A691M
1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the “M” designation (SI) of the product specification is specified in the order.
Note 1: The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.”
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:A530/A530M −18
Standard Specification for
General Requirements for Specialized Carbon and Alloy
1
Steel Pipe
This standard is issued under the fixed designationA530/A530M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 1.6 The values stated in either inch-pound units or SI units
2 are to be regarded separately as standard. Within the text, the
1.1 This specification covers a group of requirements
SI units are shown in brackets. The values stated in each
which, with the exceptions of Section 6.3, Section 14, Section
system are not exact equivalents; therefore, each system must
21, and Section 22, are mandatory requirements to theASTM
beusedindependentlyoftheother.Combiningvaluesfromthe
pipe product specifications noted below unless the product
two systems may result in nonconformance with the specifi-
specificationspecifiesdifferentrequirements,inwhichcasethe
cation. The inch-pound units shall apply unless the “M”
requirement of the product specification shall prevail.
designation (SI) of the product specification is specified in the
1.2 Sections 6.3 or 21 are mandatory if the product speci-
order.
fication has a requirement for product analysis or flattening
NOTE 1—The dimensionless designator NPS (nominal pipe size) has
tests.
been substituted in this standard for such traditional terms as “nominal
1.3 Section 22 is mandatory if the product specification has diameter,” “size,” and “nominal size.”
a hydrostatic test requirement without defining the test param-
1.7 This standard does not purport to address all of the
eters.
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
1.4 Section 14 is for information only.
priate safety, health, and environmental practices and deter-
1.5 In case of conflict between a requirement of the product
mine the applicability of regulatory limitations prior to use.
specification and a requirement of this general requirement
1.8 This international standard was developed in accor-
specification, only the requirement of the product specification
dance with internationally recognized principles on standard-
need be satisfied.
ization established in the Decision on Principles for the
A
Title of Specification ASTM Designation
Development of International Standards, Guides and Recom-
Seamless Carbon Steel Pipe for High-Temperature Service A106/A106M
mendations issued by the World Trade Organization Technical
Metal-Arc-Welded Steel Pipe for Use With High-Pressure A381
Transmission Systems
Barriers to Trade (TBT) Committee.
Seamless Carbon Steel Pipe for Atmospheric and Lower A524
Temperatures
2. Referenced Documents
Centrifugally Cast Carbon Steel Pipe for High-Temperature A660/A660M
Service
3
2.1 ASTM Standards:
Electric-Fusion-Welded Steel Pipe for Atmospheric and A671/A671M
Lower Temperatures A106/A106MSpecification for Seamless Carbon Steel Pipe
Electric-Fusion-Welded Steel Pipe for High-Pressure Service A672/A672M
for High-Temperature Service
at Moderate Temperatures
A370Test Methods and Definitions for Mechanical Testing
Carbon and Alloy Steel Pipe, Electric-Fusion-Welded for A691/A691M
High-Pressure Service at High Temperatures of Steel Products
A381Specification for Metal-Arc-Welded Carbon or High-
A
These designations refer to the latest issue of the respective specifications.
Strength Low-Alloy Steel Pipe for Use With High-
Pressure Transmission Systems
A450/A450MSpecification for General Requirements for
Carbon and Low Alloy Steel Tubes
A524Specification for Seamless Carbon Steel Pipe for
1
This specification is under the jurisdiction ofASTM Committee A01 on Steel,
Atmospheric and Lower Temperatures
Stainless Steel and RelatedAlloysand is the direct responsibility of Subcommittee
A01.09 on Carbon Steel Tubular Products.
Current edition approved Sept. 1, 2018. Published September 2018. Originally
3
approved in 1965. Last previous edition approved in 2012 as A530/A530M–12. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
DOI: 10.1520/A0530_A0530M-18. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi- Standards volume information, refer to the standard’s Document Summary page on
cation SA-530 in Section II of that Code. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM Internat
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A530/A530M − 12 A530/A530M − 18
Standard Specification for
General Requirements for Specialized Carbon and Alloy
1
Steel Pipe
This standard is issued under the fixed designation A530/A530M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
2
1.1 This specification covers a group of requirements which, with the exceptions of Section 6.3, Section 14, Section 21, and
Section 22, are mandatory requirements to the ASTM pipe product specifications noted below unless the product specification
specifies different requirements, in which case the requirement of the product specification shall prevail.
1.2 Sections 6.3 or 21 are mandatory if the product specification has a requirement for product analysis or flattening tests.
1.3 Section 22 is mandatory if the product specification has a hydrostatic test requirement without defining the test parameters.
1.4 Section 14 is for information only.
1.5 In case of conflict between a requirement of the product specification and a requirement of this general requirement
specification, only the requirement of the product specification need be satisfied.
A
Title of Specification ASTM Designation
Seamless Carbon Steel Pipe for High-Temperature A106/A106M
Service
Seamless Carbon Steel Pipe for High-Temperature A106/A106M
Service
Metal-Arc-Welded Steel Pipe for Use With High- A381
Pressure Transmission Systems
Metal-Arc-Welded Steel Pipe for Use With High-Pressure A381
Transmission Systems
Seamless Carbon Steel Pipe for Atmospheric and A524
Lower
Temperatures
Seamless Carbon Steel Pipe for Atmospheric and A524
Lower
Temperatures
Centrifugally Cast Carbon Steel Pipe for High- A660
Temperature Service
Centrifugally Cast Carbon Steel Pipe for High-Temperature A660/A660M
Service
Electric-Fusion-Welded Steel Pipe for Atmospheric A671/A671M
and
Lower Temperatures
Electric-Fusion-Welded Steel Pipe for Atmospheric A671/A671M
and
Lower Temperatures
Electric-Fusion-Welded Steel Pipe for High-Pressure Service A672/A672M
at Moderate Temperatures
Carbon and Alloy Steel Pipe, Electric-Fusion-Welded for A691/A691M
High-Pressure Service at High Temperatures
Electric-Fusion-Welded Steel Pipe for High-Pressure A672/A672M
Service at Moderate Temperatures
Carbon and Alloy Steel Pipe, Electric-Fusion-Welded A691/A691M
for High-Pressure Service at High Temperatures
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.09
on Carbon Steel Tubular Products.
Current edition approved May 1, 2012Sept. 1, 2018. Published June 2012September 2018. Originally approved in 1965. Last previous edition approved in 20102012 as
A530/A530M–04a(2010).A530/A530M – 12. DOI: 10.1520/A0530_A0530M-12.10.1520/A0530_A0530M-18.
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SA-530 in Section II of that Code.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A530/A530M − 18
A
These designations refer to the latest issue of the respective specifications.
2
---------------------- Page: 2 ----------------------
A530/A530M − 18
1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units
are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used
independently of the other. Combining values from the two systems may result in nonconformance with the specification. The
inch-pound units shall apply unless the “M” designation (SI) of the product specification is specified in the order.
NOTE 1—The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,”
“size,” and “nominal size.”
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and det
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.