iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D4022/D4022M-07(2012)e1

(Specification)

Standard Specification for Coal Tar Roof Cement, Asbestos Containing (Withdrawn 2014)

Standard Specification for Coal Tar Roof Cement, Asbestos Containing (Withdrawn 2014)

ABSTRACT
This specification covers asbestos containing coal tar roof cement suitable for trowel application in coal tar roofing and flashing systems. Coal tar roof cement shall consist of a processed coal tar base, volatile solvents, and mineral fillers including asbestos fibers, mixed to a smooth, uniform consistency. The composition of coal tar roof cement shall conform to the requirements prescribed for water content, nonvolatile matter content, and insoluble matter content. Coal tar roof cement shall meet the performance requirements specified for: (1) uniformity, (2) workability, (3) behavior at the specified temperature, (4) adhesion to wet surfaces, and (5) flash point. Conformance to the composition and performance requirements shall be determined by the specified test methods.
SCOPE
1.1 This specification covers coal tar roof cement suitable for trowel application in coal tar roofing and flashing systems.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This specification covered coal tar roof cement suitable for trowel application in coal tar roofing and flashing systems.
Formerly under the jurisdiction of Committee D08 on Roofing and Waterproofing, this specification was withdrawn in May 2014. This standard is being withdrawn without replacement due to its limited use by industry.

General Information

Status
Withdrawn
Publication Date
30-Apr-2012
Withdrawal Date
19-May-2014
ICS
91.100.10 - Cement. Gypsum. Lime. Mortar
Technical Committee
D08 - Roofing and Waterproofing
Drafting Committee
D08.05 - Solvent-Bearing Bituminous Compounds for Roofing and Waterproofing
Current Stage
Ref Project

Relations

Replaces
ASTM D4022-07 - Standard Specification for Coal Tar Roof Cement, Asbestos Containing
Effective Date
01-May-2012

Buy Standard

ASTM D4022/D4022M-07(2012)e1 - Standard Specification for Coal Tar Roof Cement, Asbestos Containing (Withdrawn 2014)ASTM D4022/D4022M-07(2012)e1 - Standard Specification for Coal Tar Roof Cement, Asbestos Containing (Withdrawn 2014)
PreviousNext
Technical specification
ASTM D4022/D4022M-07(2012)e1 - Standard Specification for Coal Tar Roof Cement, Asbestos Containing (Withdrawn 2014)
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation: D4022/D4022M −07(Reapproved 2012)
Standard Specification for
Coal Tar Roof Cement, Asbestos Containing
This standard is issued under the fixed designation D4022/D4022M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
´ NOTE—Units information was editorially corrected in June 2012.
1. Scope 3. Materials and Manufacture
1.1 This specification covers coal tar roof cement suitable 3.1 Coal tar roof cement shall consist of a processed coal tar
for trowel application in coal tar roofing and flashing systems. base, volatile solvents, and mineral fillers including asbestos
fibers, mixed to a smooth, uniform consistency suitable for
1.2 The values stated in either SI units or inch-pound units
trowel application.
are to be regarded separately as standard. The values stated in
each system may not be exact equivalents; therefore, each
4. Composition
system shall be used independently of the other. Combining
4.1 The composition of coal tar roof cement shall conform
values from the two systems may result in non-conformance
to the requirements prescribed in Table 1.
with the standard.
5. Performance Requirements
1.3 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
5.1 Uniformity—A thoroughly stirred sample shall show no
responsibility of the user of this standard to establish appro-
separation of solvent or settling that cannot be overcome by
priate safety and health practices and determine the applica-
moderate stirring after standing for 72 h at room temperature in
bility of regulatory limitations prior to use.
a closed container.
5.2 Workability—The cement shall be of such a consistency
2. Referenced Documents
thatitwillspreadreadilyandpermittrowelingsmoothcoatings
2.1 ASTM Standards:
1 1
1.6 to 3.2 mm [ ⁄16 to ⁄8 in.] thick on vertical surfaces.
D4 Test Method for Bitumen Content
5.3 Behavior at 60°C [140°F]—The cement shall show no
D95 Test Method for Water in Petroleum Products and
evidence of blistering, and the sag or slide shall be no greater
Bituminous Materials by Distillation
than6mm[ ⁄4 in.].
D140 Practice for Sampling Bituminous Materials
D3143 Test Method for Flash Point of CutbackAsphalt with 5.4 Adhesion to Wet Surfaces—Minimum average 75 %.
Tag Open-Cup Apparatus
5.5 Flash Point—38°C [100°F] minimum.
D3409 Test Method for Adhesion of Asphalt-Roof Cement
to Damp, Wet, or Underwater Surfaces 6. Sampling
D6511 Test Methods for Solvent Bearing Bituminous Com-
6.1 Sample the material from the original container imme-
pounds
diately after stirring to a uniform consistency, in accordance
with Practice D140.
6.2 Restir samples to obtain uniformity immediately before
This specification is under the jurisdiction of ASTM Committee D08 on
Roofing and Waterproofing and is the direct responsibility of Subcommittee D08.05 withdrawing portions for individual tests.
on Solvent-Bearing Bituminous Compounds for Roofing and Waterproofing.
Current edition approved May 1, 2012. Published June 2012. Originally 7. Test Methods
approved in 1981
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D8109-17(2024)(Guide)
Standard Guide for Waterproofing Repair of Concrete by Chemical Grout Crack Injection

SIGNIFICANCE AND USE
4.1 This guide is intended to be used in the selection and installation of chemical grout to seal leaks in concrete walls, floors, and ceilings. The procedure described in this guide focuses on the injection of through-wall cracks, but may be adapted to cold joints, control joints, voids associated with penetrations, and other voids contributing to water intrusion through concrete elements. This guide is intended to assist the building owner, owner’s representative, architect, engineer, contractor, or authorized inspector, or combinations thereof, during the selection, specification, or installation, or combinations thereof, of chemical grout for waterproofing repair.  
4.2 Prior to attempting any repair, it is important for all parties to have a clear and mutual understanding of the limitations of the repair and the iterative nature of the process. Injection of chemical grout does not affect the source of a leak. The repair obstructs the infiltration of water at a specific location only. The flow of water will be diverted elsewhere, and it is common for water to subsequently appear at a different location that was previously dry. A successful campaign at a given location can significantly reduce the amount of water infiltration, but may not fully prevent leakage. Given the nature of the materials and application technique, and depending on the conditions, the repairs should be periodically monitored and additional repair installations may be required.  
4.3 This guide is applicable to installations at below-grade walls and slabs. At above-grade elements, temperature variation on a daily or seasonal basis may lead to significant or more frequent changes, or both, in the width of a crack or joint. The use of injected chemical grout may be appropriate for many above-grade applications, but this guide does not specifically address installation of grout in dynamic cracks or joints.  
4.4 Cracks in below-grade walls may be a sign of structural distress. Prior to the i...
SCOPE
1.1 This guide describes the selection of materials, installation methods, and inspection required for sealing leaks at cracks in concrete building walls and slabs using chemical grout. The process discussed in this guide is a waterproofing repair in which voids in a concrete element are sealed with a reactive solution, installed by pressurized injection through drilled or surface-mounted ports.  
1.2 This guide does not address the use of chemical grout for waterproofing by curtain grouting or injection into preplaced permeable waterstop tubes. Injection of masonry elements presents additional factors beyond the scope of this guide. This guide does not address the use of injectable materials for structural repairs or for geotechnical applications such as soil stabilization.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    6 pages
    English language
    sale 15% off
ASTM
ASTM D3409/D3409M-93(2023)(Test Method)
Standard Test Method for Adhesion of Asphalt-Roof Cement to Damp, Wet, or Underwater Surfaces

SIGNIFICANCE AND USE
3.1 This test method offers a means of evaluating the adhesive properties of asphalt roofing cements used to repair roofs under adverse conditions. Weathered roof surfaces are easily coated with asphalt roofing cements when they are dry, however when wet or during a rain, asphalt roofing cements may not adhere readily to water-wet surfaces such as metal flashings or asphalt roll roofing. The flamed metal lids used in this test method simulate weathered roof surfaces.
SCOPE
1.1 This test method covers the determination of the adhesion of asphalt roofing cements to damp, wet, or underwater surfaces.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM C1178/C1178M-24(Specification)
Standard Specification for Coated Glass Mat Water-Resistant Gypsum Backing Panel

ABSTRACT
This specification covers coated glass mat water-resistant gypsum backing panel designed for use on ceilings and walls in bath and shower areas as a base for the application of ceramic or plastic tile. Coated glass mat water-resistant gypsum backing panel shall consist of a noncombustible water-resistant gypsum core, surfaced with glass mat, partially or completely embedded in the core, and with a water-resistant coating on one surface. The specimens shall be tested for flexural strength, humidified deflection, core hardness, end hardness, edge hardness, nail pull resistance, water resistance, and surface water absorption. Coated glass mat water-resistant gypsum backing panel shall have surfaces true and free of imperfections that render the panel unfit for its designed use.
SCOPE
1.1 This specification covers coated glass mat water-resistant gypsum backing panel designed for use on ceilings and walls in bath and shower areas as a base for the application of ceramic or plastic tile.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Within the text, the SI units are shown in brackets.  
1.3 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM C1177/C1177M-24(Specification)
Standard Specification for Glass Mat Gypsum Substrate for Use as Sheathing

ABSTRACT
This specification covers the requirements for glass mat gypsum substrates designed to be used as exterior substrate or sheathing for weather barriers. The substrates shall consist of a noncombustible water-resistant gypsum core, surfaced with glass mat partially or completely embedded in the core. Materials shall be sampled, tested, and conform accordingly to specified physical property (flexural strength, humidified deflection, nail pull resistance, water resistance, and core, end, and edge hardness) and dimensional (thickness, width, length, end squareness, and edges) requirements.
SCOPE
1.1 This specification covers glass mat gypsum substrate, which is designed to be used as an exterior substrate for a weather barrier.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM C1012/C1012M-24(Test Method)
Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution

SIGNIFICANCE AND USE
3.1 This test method provides a means of assessing the sulfate resistance of mortars made using portland cement, blends of portland cement with pozzolans or slags, and blended hydraulic cements. Test Method C452 is suitable for evaluating portland cements but not blended cements or blends of portland cement with pozzolans or slags.  
3.2 The standard exposure solution used in this test method, unless otherwise directed, contains 352 moles of Na2SO4 per m3(50 g/L). Other sulfate concentrations or other sulfates such as MgSO4 may be used to simulate the environmental exposure of interest. Further discussion of these and other technical issues is given in the Appendix.
SCOPE
1.1 This test method covers the determination of length change of mortar bars immersed in a sulfate solution. Mortar bars made using mortar described in Test Method C109/C109M are cured until they attain a compressive strength of 20.0 MPa ± 1.0 MPa [3000 psi ± 150 psi], as measured using cubes made of the same mortar, before the bars are immersed.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM C1789-24(Test Method)
Standard Test Method for Calibration of Hand-Held Moisture Meters on Gypsum Panels

SIGNIFICANCE AND USE
5.1 This Standard Test Method is intended for use in calibrating hand-held meters to accurately read from approximately 30 % to 90 % ERH. Moisture content is related to the ERH or Aw of a material.  
5.2 Hand-held meters provide a rapid means of sampling the moisture content of gypsum boards and panels during manufacture and for field inspection during and after building construction. However, these measurements are inferential, that is, electrical parameters are measured and compared against a calibration curve to obtain an indirect measure of moisture content. The electrical measurements are influenced by the actual moisture content, a number of other gypsum board and panel variables, environmental conditions, the geometry of the measuring probe, and the design of the meter. The maximum accuracy can only be obtained by an awareness of the effect of each parameter on the meter output and correction of readings as specified by these test methods.  
5.3 Electrical conductance and dielectric meters are not necessarily equivalent in their readings under the same conditions. When this test method is referenced, the type of meter that is being used must be reported with the relevant ranges for precision and bias as specified in this standard.  
5.4 Both types of meters are to be calibrated with respect to ERH as described in this standard.
SCOPE
1.1 This test method applies to the calibration of hand-held moisture meters for gypsum board, glass faced gypsum panels and fiber-reinforced gypsum panels by means of electrical conductance and dielectric meters. The test uses wetted test specimens which are dried down in at least five (5) steps to determine the moisture content based on the weight loss in comparison to the dry weight. The test also supplies the ERH values for each of the drying steps.  
1.2 This test method has not been evaluated for the influence of paint or wall covering materials on the indicated moisture content of a gypsum board or panel substrate.  
1.3 The values stated in SI (metric) are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM C1038/C1038M-24(Test Method)
Standard Test Method for Expansion of Hydraulic Cementitious Material Mortar Bars Stored in Water

SIGNIFICANCE AND USE
4.1 This test method is used to determine the amount of expansion of a mortar bar when it is stored in water. The amount of mortar-bar expansion may relate to the amount of sulfate in the cementitious material; expansion may become excessive when the cementitious material contains too much sulfate.  
4.2 Some cementitious material specifications limit the amount of sulfate contained in those materials by requiring that the amount of expansion in water not exceed a specified value.
SCOPE
1.1 This test method covers the determination of the expansion of mortar bars made using hydraulic cementitious materials, of which sulfate is an integral part.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 The text of this standard refers to notes and footnotes that provide explanatory material. These notes shall not be considered as requirements of the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.2)  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM C471M-24(Test Method)
Standard Test Methods for Chemical Analysis of Gypsum and Gypsum Products (Metric)

SCOPE
1.1 These test methods cover the chemical analysis of gypsum and gypsum panel products, including gypsum ready-mixed plaster, gypsum wood-fibered plaster, and gypsum concrete.  
1.2 These test methods appear in the following order:    
Sections  
Preparation of Sample  
4  
Complete Procedure  
5 – 16  
Alternative Procedure for Analysis of Free Water in  
17  
Gypsum Using a Moisture Balance  
Alternative Procedure for Analysis of Combined Water in  
18  
Gypsum Using a Moisture Balance  
Alternative Procedure for Analysis of Organic Material  
20  
and Carbon Dioxide in Gypsum by High Temperature  
Weight Loss  
Alternative Procedure for Analysis for Calcium Sulfate by  
21  
Ammonium Acetate Method  
Alternative Procedure for Analysis for Sodium Chloride by  
22  
the Coulometric Method  
Determination of Sand in Set Plaster  
23  
Wood-fiber Content in Wood-fiber Gypsum Plaster  
24  
Optional Procedure for Analysis for Sodium by the Atomic  
25  
Absorption Method  
Optional Procedure for Analysis for Sodium by Flame  
26  
Photometry  
Determination of Orthorhombic Cyclooctasulfur (S8) in  
27  
Ggypsum Panel Products—General Provisions  
Determination of Orthorhombic Cyclooctasulfur (S8) in  
28  
Gypsum Panel Products by Gas Chromatograph  
Equipped with a Mass Spectrometer (GS/MS)  
Determination of Orthorhombic Cyclooctasulfur (S8) in  
29  
Gypsum Panel Products by Gas Chromatograph  
Equipped with an Electron Capture Detector (GC/ECD)  
Determination of Orthorhombic Cyclooctasulfur (S8) in  
30  
Gypsum Panel Products by High-performance Liquid  
Chromatograph Equipped with and Ultraviolet Detector  
(HPLC/UV)  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in these test methods.  
1.4 These text of this test method references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    19 pages
    English language
    sale 15% off
  • Standard
    19 pages
    English language
    sale 15% off
ASTM
ASTM C317/C317M-24(Specification)
Standard Specification for Gypsum Concrete

ABSTRACT
This specification covers mill-mixed gypsum concrete, consisting essentially of calcined gypsum and suitable aggregate, requiring the addition of water only at the job site. Gypsum concrete is intended for use in the construction of poured-in-place roof decks or slabs. Two classes, based on the compressive strength and density, are covered. Gypsum concrete shall consist of calcined gypsum to which are added aggregates, wood chips, or wood shavings in proportion to meet the applicable requirements of this specification. Test method in this specification shall be performed in order to determine the physical properties of the gypsum concrete. Setting time is determined by the Vicat method.
SCOPE
1.1 This specification covers mill-mixed gypsum concrete, consisting essentially of calcined gypsum and suitable aggregate, requiring the addition of water only at the job site. Gypsum concrete is intended for use in the construction of poured-in-place roof decks or slabs. Two classes, based on the compressive strength and density, are covered.  
1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM C1875-18(2024)(Practice)
Standard Practice for Determination of Major and Minor Elements in Aqueous Pore Solutions of Cementitious Pastes by Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES)

SIGNIFICANCE AND USE
5.1 The chemical composition of the liquid in cementitious pastes is an important indicator of the solid component reactivity at early times, being influenced by the content and rate of reaction of readily soluble alkali components, lime, and other soluble phases. Monitoring the solution composition with time can provide valuable diagnostic information about cement quality and reactivity to supplement other sources of characterization data. This practice is intended to aid in the interpretation of the concentrations of readily soluble components in cement paste solutions, which may include portland cement, limestone, fly ash, ground granulated blast furnace slag, or other components. It provides guidance for measuring the time dependence of the concentrations of one or more components, on an elemental basis, including, but not limited to, aluminum, calcium, potassium, silicon, sodium, and sulfur.
SCOPE
1.1 This practice describes a procedure for collection, sample preparation and analysis of aqueous pore solutions obtained from cementitious materials at different hydration times when analyzed by ICP-OES for the six most common readily soluble elements aluminum, calcium, potassium, silicon, sodium and sulfur.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off