ASTM F1499-01(2008)

Standard Specification for Coextruded Composite Drain, Waste, and Vent Pipe (DWV)

ABSTRACT
This specification covers co extruded composite drain, waste, and vent pipe (DWV). The pipe is produced in Schedule 40 IPS sizes by a co extrusion die system, in which the concentric layers are formed and combined before exiting the die. Coextruded composite drain, waste, and vent pipe, DWV, by definition, is permitted to be produced with two or more layers. The outer layer shall be ABS. The middle layer is permitted to be thermally foamed PVC or solid PVC or a blend of rework material, as specified. The inner layer is permitted to be solid PVC or ABS, or a blend of rework material as specified. The basic material used for pipes is a virgin compound which is used in the outer layer of co extruded composite drain, waste, and vent pipe or (DWV). It shall contain pigments or screening agents to provide protection against UV radiation. Different tests and measurements shall be conducted in order to determine the following properties of pipes: outside diameter, wall thickness, length, pipe flattening, pipe stiffness, impact strength, and bond. The inside and outside surfaces of pipe produced shall be free of chalking, sticky, or tacky material. The surfaces shall be free of excessive bloom. Bloom or chalking may develop in pipe exposed to direct rays of the sun (ultraviolet radiant energy) for extended periods and consequently, these requirements do not apply to pipe after extended exposure to direct rays of the sun. The inside and outside surfaces of pipe shall be free of foreign inclusion or other defects that re visible to the naked eye, and may affect the wall integrity.
SCOPE
1.1 This specification covers coextruded composite drain, waste, and vent pipe (DWV). The pipe is produced in Schedule 40 IPS sizes by a coextrusion die system, in which the concentric layers are formed and combined before exiting the die.  
1.1.1 Coextruded composite drain, waste, and vent pipe, DWV, by definition, is permitted to be produced with two or more layers. The outer layer shall be ABS. The middle layer is permitted to be thermally foamed PVC or solid PVC or a blend of rework material, as specified in the rework material section. The inner layer is permitted to be solid PVC or ABS, or a blend of rework material as specified in the rework material section.
1.1.2 The function of this specification is to provide standardization of product, technical data, and serve as a purchasing guide.  
1.2 DWV is permitted to be produced utilizing a two layer or three layer coextrusion die.
1.3 Materials that do not meet the requirements of the material section are excluded.
1.4 Pipe produced to this specification is permitted to be joined using molded fittings meeting the requirements of Specification D 2661 or Specification F 628. The fitting patterns must comply with Specification D 3311.
1.5 Pipe produced to this specification is permitted to be perforated in accordance with any specified standard or by agreement between the purchaser and the supplier.
1.6 Pipe produced to this specification is permitted to be belled for joining by solvent cementing or belled for joining by an elastomeric seal (gasket), in accordance with any specified standard or by agreement between the purchaser and the supplier.
1.7 Recommendations for storage, joining, and installation are provided in Appendix X1, Appendix X2, and Appendix X3, respectively.
1.8 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.
1.9 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.  
1.10 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered st...

General Information

• Status: Historical
• Publication Date: 31-Oct-2008
• ICS: 93.030 - External sewage systems
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.63 - DWV

Relations

• Replaces: ASTM F1499-01 - Standard Specification for Coextruded Composite Drain, Waste, and Vent Pipe (DWV)
• Effective Date: 01-Nov-2008
• Replaced By: ASTM F1499-12 - Standard Specification for Coextruded Composite Drain, Waste, and Vent Pipe (DWV)
• Effective Date: 01-Apr-2012
• Referred By: ASTM F412-23 - Standard Terminology Relating to Plastic Piping Systems
• Effective Date: 01-Nov-2008

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: F1499 – 01 (Reapproved 2008)
Standard Specification for
1
Coextruded Composite Drain, Waste, and Vent Pipe (DWV)
This standard is issued under the fixed designation F1499; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 1.9 Thetextofthisspecificationreferencesnotes,footnotes,
and appendixes which provide explanatory material. These
1.1 This specification covers coextruded composite drain,
notesandfootnotes(excludingthoseintablesandfigures)shall
waste,andventpipe(DWV).ThepipeisproducedinSchedule
not be considered as requirements of this specification.
40 IPS sizes by a coextrusion die system, in which the
1.10 The values stated in inch-pound units are to be re-
concentric layers are formed and combined before exiting the
garded as standard. The values given in parentheses are
die.
mathematical conversions to SI units that are provided for
1.1.1 Coextruded composite drain, waste, and vent pipe,
information only and are not considered standard.
DWV, by definition, is permitted to be produced with two or
1.11 This standard does not purport to address all of the
more layers.The outer layer shall beABS.The middle layer is
safety concerns, if any, associated with its use. It is the
permittedtobethermallyfoamedPVCorsolidPVCorablend
responsibility of the user of this standard to establish appro-
of rework material, as specified in the rework material section.
priate safety and health practices and determine the applica-
TheinnerlayerispermittedtobesolidPVCorABS,orablend
bility of regulatory limitations prior to use.
of rework material as specified in the rework material section.
1.1.2 The function of this specification is to provide stan-
NOTE 1—Specifications related to this specification are as follows:
dardization of product, technical data, and serve as a purchas- Specifications D2661, D2665, F628, and F891.
ing guide.
2. Referenced Documents
1.2 DWV is permitted to be produced utilizing a two layer
or three layer coextrusion die. 2.1 The following standards contain provisions that, though
referenced in this specification, constitute provisions of this
1.3 Materials that do not meet the requirements of the
material section are excluded. specification. All standards are subject to revision and parties
using this specification, shall reference the most recent edition
1.4 Pipe produced to this specification is permitted to be
of the standards listed as follows:
joined using molded fittings meeting the requirements of
2
SpecificationD2661orSpecificationF628.Thefittingpatterns 2.2 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
must comply with Specification D3311.
1.5 Pipe produced to this specification is permitted to be D696 Test Method for Coefficient of Linear Thermal Ex-
pansion of Plastics Between Ø30°C and 30°C with a
perforated in accordance with any specified standard or by
agreement between the purchaser and the supplier. Vitreous Silica Dilatometer
D883 Terminology Relating to Plastics
1.6 Pipe produced to this specification is permitted to be
belledforjoiningbysolventcementingorbelledforjoiningby D1600 Terminology for Abbreviated Terms Relating to
Plastics
an elastomeric seal (gasket), in accordance with any specified
3
standard or by agreement between the purchaser and the D1898 Practice for Sampling of Plastics
D1972 Practice for Generic Marking of Plastic Products
supplier.
1.7 Recommendations for storage, joining, and installation
areprovidedinAppendixX1,AppendixX2,andAppendixX3,
respectively.
1.8 Thevaluesstatedininch-poundunitsaretoberegarded
as the standard. The SI units given in parentheses are for
information only.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Nov. 1, 2008. Published February 2009. Originally the ASTM website.
3
published as approved in 1994. Last previous edition approved in 2001 as Withdrawn. The last approved version of this historical standard is referenced
F1499–01. DOI: 10.1520/F1499-01R08. on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F1499 – 01 (2008)
7
D2122 Test Method for Determining Dimensions of Ther- Uniform Fr
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:F 1499–00 Designation: F 1499 – 01 (Reapproved 2008)
Standard Specification for
1
Coextruded Composite Drain, Waste, and Vent Pipe (DWV)
This standard is issued under the fixed designation F 1499; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers coextruded composite drain, waste, and vent pipe (DWV). The pipe is produced in Schedule 40
IPS sizes by a coextrusion die system, in which the concentric layers are formed and combined before exiting the die.
1.1.1 Coextruded composite drain, waste, and vent pipe, DWV, by definition, is permitted to be produced with two or more
layers.TheouterlayershallbeABS.ThemiddlelayerispermittedtobethermallyfoamedPVCorsolidPVCorablendofrework
material, as specified in the rework material section. The inner layer is permitted to be solid PVC or ABS, or a blend of rework
material as specified in the rework material section.
1.1.2 Thefunctionofthisspecificationistoprovidestandardizationofproduct,technicaldata,andserveasapurchasingguide.
1.2 DWV is permitted to be produced utilizing a two layer or three layer coextrusion die.
1.3 Materials that do not meet the requirements of the material section are excluded.
1.4 PipeproducedtothisspecificationispermittedtobejoinedusingmoldedfittingsmeetingtherequirementsofSpecification
D2661 or Specification F628. The fitting patterns must comply with Specification D3311.
1.5 Pipe produced to this specification is permitted to be perforated in accordance with any specified standard or by agreement
between the purchaser and the supplier.
1.6 Pipe produced to this specification is permitted to be belled for joining by solvent cementing or belled for joining by an
elastomeric seal (gasket), in accordance with any specified standard or by agreement between the purchaser and the supplier.
1.7 Recommendations for storage, joining, and installation are provided in Appendix X1, Appendix X2, and Appendix X3,
respectively.
1.8 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for
information only.
1.9 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes
and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.
1.10
1.10 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.11 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
NOTE 1—Specifications related to this specification are as follows: Specifications D2661, D2665, F628, and F891.
2. Referenced Documents
2.1 The following standards contain provisions that, though referenced in this specification, constitute provisions of this
specification.Allstandardsaresubjecttorevisionandpartiesusingthisspecification,shallreferencethemostrecenteditionofthe
standards listed as follows:
2
2.2 ASTM Standards:
D618 Practice for Conditioning Plastics and Electrical Insulating Materials for Testing Practice for Conditioning Plastics for
Testing
D696 Test Method for Coefficient of Linear Thermal Expansion of Plastics Test Method for Coefficient of Linear Thermal
Expansion of Plastics Between 30C and 30C with a Vitreous Silica Dilatometer
D883 Terminology Relating to Plastics
1
This specification is under the jurisdiction ofASTM Committee F-17F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
Current edition approved May 10, 2000.Nov. 1, 2008. PublishedAugust 2000.February 2009. Originally published as F1499–94. approved in 1994. Last previous edition
F1499–98.approved in 2001 as F1499–01.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,[e-mail] Annual Book of ASTM Standards
, Vol 08.01.volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor
...