ASTM B709-04(2014)
(Specification)Standard Specification for Iron-Nickel-Chromium-Molybdenum Alloy (UNS N08028) Plate, Sheet, and Strip
Standard Specification for Iron-Nickel-Chromium-Molybdenum Alloy (UNS N08028) Plate, Sheet, and Strip
ABSTRACT
This specification covers solution-annealed UNS N08028 iron-nickel-chromium-molybdenum alloy plates, sheets, and strips. In preparing the materials, the final heat treatment should be a solution-anneal which can be followed by minor cold working such as flattening or temper rolling. The recommended solution-anneal consists of heating to a minimum temperature and rapid cooling.
SCOPE
1.1 This specification covers iron-nickel-chromium-molybdenum alloy (UNS N08028)2 plate, sheet, and strip in the solution-annealed condition.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B709 −04 (Reapproved 2014)
Standard Specification for
Iron-Nickel-Chromium-Molybdenum Alloy (UNS N08028)
1
Plate, Sheet, and Strip
This standard is issued under the fixed designation B709; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope specification. Examples of such requirements include, but are
not limited to those specified in Ordering Information Section
1.1 This specification covers iron-nickel-chromium-
2 in Specification B906.
molybdenum alloy (UNS N08028) plate, sheet, and strip in
the solution-annealed condition.
4. General Requirements
1.2 The values stated in inch-pound units are to be regarded
4.1 Material furnished under this specification shall con-
as standard. The values given in parentheses are mathematical
form to the applicable requirements of the current edition of
conversions to SI units that are provided for information only
Specification B906, unless otherwise specified herein.
and are not considered standard.
1.3 This standard does not purport to address all of the
5. Materials and Manufacture
safety concerns, if any, associated with its use. It is the
5.1 Heat Treatment—The final heat treatment shall be a
responsibility of the user of this standard to become familiar
solution-anneal. Minor cold working such as flattening or
with all hazards including those identified in the appropriate
temper rolling may be performed after the final solution
Material Safety Data Sheet (MSDS) for this product/material
annealing treatment.
as provided by the manufacturer, to establish appropriate
safety and health practices, and determine the applicability of
NOTE 1—This recommended solution-anneal consists of heating to a
regulatory limitations prior to use.
minimum temperature of 1975°F (1080°C) and cooling rapidly to room
temperature.
2. Referenced Documents
6. Chemical Composition
3
2.1 ASTM Standards:
6.1 The material sampled in accordance with 10.2 shall
B880 Specification for General Requirements for Chemical
conform to the composition limits prescribed in Table 1.
Check Analysis Limits for Nickel, Nickel Alloys and
Cobalt Alloys
6.2 If a product analysis is subsequently made, the material
B906 Specification for General Requirements for Flat-
shall conform to the composition limits with the product
Rolled Nickel and Nickel Alloys Plate, Sheet, and Strip
analysis variation prescribed Specification B880.
E8/E8M Test Methods for Tension Testing of Metallic Ma-
terials
7. Mechanical Properties
7.1 The material shall conform to the requirements as to the
3. Ordering Information
mechanical property prescribed in Table 2.
3.1 It is the responsibility of the purchaser to specify all
requirements that are necessary for material ordered under this
8. Dimensions and Permissible Variations
8.1 Sheet—Material furnished under this specification shall
1
conformtotheapplicablerequirementsofthecurrenteditionof
This specification is under the jurisdiction of ASTM Committee B02 on
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
Specification B906, except as specified in Table 3 and Table 4.
B02.07 on Refined Nickel and Cobalt and Their Alloys.
8.2 Cold-Rolled Strip—Material furnished under this speci-
Current edition approved Oct. 1, 2014. Published October 2014. Originally
approved in 1982. Last previous edition approved in 2009 as B709 – 04 (2009).
fication shall conform to the applicable requirements of the
DOI: 10.1520/B0709-04R14.
current edition of Specification B906, except as specified in
2
New designation in accordance withASTM E527 and SAE J1086, Practice for
Tables 5-7.
Numbering Metals and Alloys (UNS).
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
8.3 Plate—Material furnished under this specification shall
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
conformtotheapplicablerequirementsofthecurrenteditionof
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. Specification B906.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B709−04 (2014)
TABLE 1 Chemical Requirements
purchase order additional material of adequate size to provide
Element Composition, % sample coupons for inspection purposes.
Ni 29.5 to 32.5
A 10. Number of Tests and Retests
Fe remainder
Cr 26.0 to 28.0
10.1 In the case of sheet or strip supplied in coil form, two
Mo 3.0 to 4.0
or more tension tests (one from each end of each coil), and one
C, max 0.030
Si, max 1.00
or more
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B709 − 04 (Reapproved 2009) B709 − 04 (Reapproved 2014)
Standard Specification for
Iron-Nickel-Chromium-Molybdenum Alloy (UNS N08028)
1
Plate, Sheet, and Strip
This standard is issued under the fixed designation B709; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
2
1.1 This specification covers iron-nickel-chromium-molybdenum alloy (UNS N08028)*N08028) plate, sheet, and strip in the
solution-annealed condition.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data
Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and
determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
B880 Specification for General Requirements for Chemical Check Analysis Limits for Nickel, Nickel Alloys and Cobalt Alloys
B906 Specification for General Requirements for Flat-Rolled Nickel and Nickel Alloys Plate, Sheet, and Strip
E8/E8M Test Methods for Tension Testing of Metallic Materials
3. Ordering Information
3.1 It is the responsibility of the purchaser to specify all requirements that are necessary for material ordered under this
specification. Examples of such requirements include, but are not limited to those specified in Ordering Information Section in
Specification B906.
4. General Requirements
4.1 Material furnished under this specification shall conform to the applicable requirements of the current edition of
Specification B906, unless otherwise specified herein.
5. Materials and Manufacture
5.1 Heat Treatment—The final heat treatment shall be a solution-anneal. Minor cold working such as flattening or temper rolling
may be performed after the final solution annealing treatment.
NOTE 1—This recommended solution-anneal consists of heating to a minimum temperature of 1975°F (1080°C) and cooling rapidly to room
temperature.
6. Chemical Composition
6.1 The material sampled in accordance with 10.2 shall conform to the composition limits prescribed in Table 1.
6.2 If a product analysis is subsequently made, the material shall conform to the composition limits with the product analysis
variation prescribed Specification B880.
1
This specification is under the jurisdiction of ASTM Committee B02 on Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee B02.07 on Refined
Nickel and Cobalt and Their Alloys.
Current edition approved April 15, 2009Oct. 1, 2014. Published April 2009October 2014. Originally approved in 1982. Last previous edition approved in 20042009 as
B709 – 98 (2004).B709 – 04 (2009). DOI: 10.1520/B0709-04R09.10.1520/B0709-04R14.
2
New designation in accordance with ASTM E527 and SAE J1086, Practice for Numbering Metals and Alloys (UNS).
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’sstandard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B709 − 04 (2014)
TABLE 1 Chemical Requirements
Element Composition, %
Ni 29.5 to 32.5
A
Fe remainder
Cr 26.0 to 28.0
Mo 3.0 to 4.0
C, max 0.030
Si, max 1.00
Mn, max 2.50
P, max 0.030
S, max 0.030
Cu 0.6 to 1.4
A
Determined arithmetically by difference.
7. Mechanical Properties
7.1 The material shall conform to the requirements as to the mechanical property prescribed in Table 2.
8. Dimensions and Permissible Variations
8.1 Sheet—Material furnished under this specification shall conform to the applicable requirements of the current edition of
Specification B906, except as specified in Table 3 and Table 4.
8.2 Cold-Rolled Strip—Material furnished under this specification shall conform to the applicable re
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.