Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster

ABSTRACT
This specification covers the installation of lathing and furring to receive interior and exterior Portland cement-based plaster. The following materials shall be used: metal plaster bases—expanded metal lath and wire laths; accessories—steel, PVC plastic, zinc alloy, and cornerite; channels—external corner reinforcement and foundation weep screed; wire; rod and strap hangers; clips; fasteners—nails and screws. Hangers and cold-rolled channel main runner shall conform to the allowable spacing and spans, respectively. The following methods are discussed: installation of hangers for suspended ceilings under wood constructions, attachment of hangers to main runners, installation of main runners, installation of cross furring, metal furring for walls, lapping of metal plaster bases, spacing of attachments for metal plaster bases, application of metal plaster bases, and application of accessories.
SCOPE
1.1 This specification covers the minimum technical requirements for lathing and furring for the application of exterior and interior portland cement-based plaster, as in Specifications C841 or C926. These requirements do not by default define a unit of work or assign responsibility for contractual purposes, which is the purview of a contract or contracts made between contracting entities.  
1.2 Where a fire resistance rating is required for plastered assemblies and constructions, details of construction shall be in accordance with reports of fire tests of assemblies that have met the requirements of the fire rating imposed.  
1.3 Where a specific degree of sound control is required for plastered assemblies and constructions, details of construction shall be in accordance with official reports of tests conducted in recognized testing laboratories in accordance with the applicable requirements of Test Method E90.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Historical
Publication Date
31-Mar-2018
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM C1063-18a - Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster
English language
10 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM C1063-18a - Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster
English language
10 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C1063 −18a
Standard Specification for
Installation of Lathing and Furring to Receive Interior and
1
Exterior Portland Cement-Based Plaster
This standard is issued under the fixed designation C1063; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* 2. Referenced Documents
2
2.1 ASTM Standards:
1.1 This specification covers the minimum technical re-
A653/A653M Specification for Steel Sheet, Zinc-Coated
quirements for lathing and furring for the application of
(Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed)
exterior and interior portland cement-based plaster, as in
by the Hot-Dip Process
Specifications C841 or C926. These requirements do not by
C11 Terminology Relating to Gypsum and Related Building
default define a unit of work or assign responsibility for
Materials and Systems
contractual purposes, which is the purview of a contract or
C841 Specification for Installation of Interior Lathing and
contracts made between contracting entities.
Furring
1.2 Where a fire resistance rating is required for plastered C847 Specification for Metal Lath
assembliesandconstructions,detailsofconstructionshallbein C926 Specification for Application of Portland Cement-
Based Plaster
accordance with reports of fire tests of assemblies that have
C933 Specification for Welded Wire Lath
met the requirements of the fire rating imposed.
C1032 Specification for Woven Wire Plaster Base
1.3 Where a specific degree of sound control is required for
C1280 Specification for Application of Exterior Gypsum
plastered assemblies and constructions, details of construction
Panel Products for Use as Sheathing
shallbeinaccordancewithofficialreportsoftestsconductedin
C1861 Specification for Lathing and Furring Accessories,
recognized testing laboratories in accordance with the appli-
and Fasteners, for Interior and Exterior Portland Cement-
cable requirements of Test Method E90.
Based Plaster
E90 Test Method for Laboratory Measurement of Airborne
1.4 The values stated in inch-pound units are to be regarded
Sound Transmission Loss of Building Partitions and
as standard. The values given in parentheses are mathematical
Elements
conversions to SI units that are provided for information only
2.2 US Department of Commerce (DOC) Standards
and are not considered standard.
PS 1 Voluntary Product Standard PS 1, Structural Plywood
1.5 This international standard was developed in accor-
PS 2 Voluntary Product Standard PS 2, Performance Stan-
dance with internationally recognized principles on standard-
dard for Wood-Based Structural Use Panels
ization established in the Decision on Principles for the
3. Terminology
Development of International Standards, Guides and Recom-
3.1 Definitions:
mendations issued by the World Trade Organization Technical
3.1.1 For definitions relating to ceilings and walls, see
Barriers to Trade (TBT) Committee.
Terminology C11.
3.1.2 For definitions relating to lathing accessories. furring
accessories and fasteners, see Specification C1861.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 building enclosure, n—system of building assemblies
and materials designed and installed in such a manner as to
1
This specification is under the jurisdiction of ASTM Committee C11 on
provide a barrier between different environments.
Gypsum and Related Building Materials and Systems and is the direct responsibility
ofSubcommitteeC11.03onSpecificationsfortheApplicationofGypsumandOther
2
Products in Assemblies. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved April 1, 2018. Published April 2018. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1986. Last previous edition approved in 2018 as C1063 – 18. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/C1063-18A. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C1063−18a
3.2.2 control joint, n—a joint that accommodates movement
of plaster shrinkage and curing along predetermined, usually
straight, lines.
3.2.3 expansion joint, n—a joint that accommodates move-
ment beyond plaster shrinkage and curing.
NOTE 1—For design consideration of control and expansion joints, see
Annex A2.3.1.2 of Specification C926.
3.2.4 framing member, n—studs, joist, runners (
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1063 − 18 C1063 − 18a
Standard Specification for
Installation of Lathing and Furring to Receive Interior and
1
Exterior Portland Cement-Based Plaster
This standard is issued under the fixed designation C1063; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This specification covers the minimum technical requirements for lathing and furring for the application of exterior and
interior portland cement-based plaster, as in Specifications C841 or C926. These requirements do not by default define a unit of
work or assign responsibility for contractual purposes, which is the purview of a contract or contracts made between contracting
entities.
1.2 Where a fire resistance rating is required for plastered assemblies and constructions, details of construction shall be in
accordance with reports of fire tests of assemblies that have met the requirements of the fire rating imposed.
1.3 Where a specific degree of sound control is required for plastered assemblies and constructions, details of construction shall
be in accordance with official reports of tests conducted in recognized testing laboratories in accordance with the applicable
requirements of Test Method E90.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A641/A641M Specification for Zinc–Coated (Galvanized) Carbon Steel Wire
A653/A653M Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the
Hot-Dip Process
B69 Specification for Rolled Zinc
B221 Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes
C11 Terminology Relating to Gypsum and Related Building Materials and Systems
C841 Specification for Installation of Interior Lathing and Furring
C847 Specification for Metal Lath
C926 Specification for Application of Portland Cement-Based Plaster
C933 Specification for Welded Wire Lath
C954 Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs
from 0.033 in. (0.84 mm) to 0.112 in. (2.84 mm) in Thickness
C1002 Specification for Steel Self-Piercing Tapping Screws for Application of Gypsum Panel Products or Metal Plaster Bases
to Wood Studs or Steel Studs
C1032 Specification for Woven Wire Plaster Base
C1280 Specification for Application of Exterior Gypsum Panel Products for Use as Sheathing
1
This specification is under the jurisdiction of ASTM Committee C11 on Gypsum and Related Building Materials and Systems and is the direct responsibility of
Subcommittee C11.03 on Specifications for the Application of Gypsum and Other Products in Assemblies.
Current edition approved Jan. 1, 2018April 1, 2018. Published April 2018. Originally approved in 1986. Last previous edition approved in 20172018 as
C1063 – 17a.C1063 – 18. DOI: 10.1520/C1063-18.10.1520/C1063-18A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C1063 − 18a
D1784C1861 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)
CompoundsLathing and Furring Accessories, and Fasteners, for Interior and Exterior Portland Cement-Based Plaster
D4216 Specification for Rigid Poly(Vinyl Chloride) (PVC) and Related PVC and Chlorinated Poly(Vinyl Chloride) (CPVC)
Building Products Compounds
E90
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.