iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F484-83(1998)e1

(Test Method)

Standard Test Method for Stress Crazing of Acrylic Plastics in Contact with Liquid or Semi-Liquid Compounds

Standard Test Method for Stress Crazing of Acrylic Plastics in Contact with Liquid or Semi-Liquid Compounds

SCOPE
1.1 This test method covers determination of the crazing effect that a liquid or semi-liquid test compound will have on transparent acrylic plastic material that is under bending stress.  
1.2 Three types of acrylic material are covered. One, two, or all of the materials shall be used in the test, as specified by the procuring agency. When not specified otherwise, all three types of acrylic shall be used in the test.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
20-Jul-1999
ICS
83.080.10 - Thermosetting materials
Technical Committee
F07 - Aerospace and Aircraft
Drafting Committee
F07.07 - Qualification Testing of Aircraft Cleaning Materials
Current Stage
Ref Project

Relations

Replaced By
ASTM F484-02 - Standard Test Method for Stress Crazing of Acrylic Plastics in Contact with Liquid or Semi-Liquid Compounds
Effective Date
10-May-2002
Referred By
ASTM D6361/D6361M-98(2020) - Standard Guide for Selecting Cleaning Agents and Processes
Effective Date
21-Jul-1999
Referred By
ASTM F790-23 - Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures
Effective Date
21-Jul-1999

Buy Standard

ASTM F484-83(1998)e1 - Standard Test Method for Stress Crazing of Acrylic Plastics in Contact with Liquid or Semi-Liquid CompoundsASTM F484-83(1998)e1 - Standard Test Method for Stress Crazing of Acrylic Plastics in Contact with Liquid or Semi-Liquid Compounds
PreviousNext
Standard
ASTM F484-83(1998)e1 - Standard Test Method for Stress Crazing of Acrylic Plastics in Contact with Liquid or Semi-Liquid Compounds
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
e1
Designation: F 484 – 83 (Reapproved 1998)
AMERICAN SOCIETY FOR TESTING AND MATERIALS
100 Barr Harbor Dr., West Conshohocken, PA 19428
Reprinted from the Annual Book of ASTM Standards. Copyright ASTM
Standard Test Method for
Stress Crazing of Acrylic Plastics in Contact with Liquid or
Semi-Liquid Compounds
This standard is issued under the fixed designation F 484; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
e NOTE—Keywords were added editorially in October 1998.
1. Scope 4. Types
1.1 This test method covers determination of the crazing 4.1 Type A, cast acrylic material shall conform to MIL-P-
effect that a liquid or semi-liquid test compound will have on 5425, Finish A.
transparent acrylic plastic material that is under bending stress. 4.2 Type B, cast acrylic material shall conform to MIL-P-
1.2 Three types of acrylic material are covered. One, two, or 8184, Finish B.
all of the materials shall be used in the test, as specified by the 4.3 Type C, stretched acrylic material shall conform to
procuring agency. When not specified otherwise, all three types MIL-P-25690.
of acrylic shall be used in the test.
5. Apparatus
1.3 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the 5.1 Stress Apparatus—The means of stressing the acrylic
plastic test specimen bars shall be as shown in Fig. 1.
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
6. Test Specimens
bility of regulatory limitations prior to use.
6.1 The test specimens shall be machined from 0.25 6
2. Referenced Documents
0.025 in. (6.4 6 0.64 mm) thick polished acrylic plastic sheet
conforming to the applicable specification.
2.1 ASTM Standards:
D 1193 Specification for Reagent Water 6.2 The test specimens shall be 1 6 0.03 in. (25.4 6 0.8
mm) wide by 7 6 0.05 in. (177.8 6 1.27 mm) long by 0.25 6
2.2 Military Standards:
MIL-P-5425 Plastic Sheet, Acrylic, Heat Resistant 0.025 in. (6.4 6 0.64 mm) thick. Edges shall be a smooth
machined surface without cracks.
MIL-P-8184 Plastic Sheet, Acrylic, Modified
MIL-P-25690 Plastic Sheets and Parts, Modified, Acrylic-
3 7. Conditioning
Basic, Monolithic, Crack Propagation Resistant
7.1 Do not anneal Type C acrylic specimens.
3. Terminology
7.2 Anneal Type A and Type B acrylic test specimens after
3.1 Definitions: machining by heating in a circulating air oven at 195 6 5°F
(916 3°C) for 5 ⁄2 h. Cool the specimens to room temperature
3.1.1 craze—a minute surface crack, sometimes hairline in
size. in the oven using a uniform cooling rate of 50°F (28°C)/h.
7.3 Condition all specimens at 75 6 10°F and 50 6 5%
NOTE 1—Hairline craze cracks are very difficult to see except with
relative humidity for a minimum of 24 h just before testing.
careful inspection under properly oriented light.
3.1.2 crack—a fracture or tear. 8. Procedure
8.1 Test two specimens of each acrylic material specified for
each of the test compounds being evaluated.
1 8.2 Conduct the test at a temperature of 75 6 10°F (23 6
This test method is under the jurisdiction of ASTM Committee F-7 on
5°C).
Aerospace and Aircraft and is the direct responsibility of Subcommittee F07.07 on
Qualification Testing of Aircraft Cleaning Materials.
8.3 Carefully load the acrylic specimen as a cantilever beam
Current edition approved Sept. 30, 1983. Published February 1984. Originally
as shown in Fig. 1. Unless otherwise specified, the following
published as F 484 – 77. Last previous edition F 484 – 77.
are recommended stress levels:
Annual Book of ASTM Standards, Vol 11.01.
Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 8.3.1 Type A specimens shall be stressed to an outer fiber
Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
F 484
Load: outer fiber stress 3000 psi (20 685 kPa) Type A acrylic
outer fiber stress 3500 psi (24 132 kPa) Type B acrylic
outer fiber stress 4500 psi (31 027 kPa) Type C acrylic
stress in psi
Formula:
load, lb 5 w 3 t 3
stress in kPa
load, g 5 w 3 t 3
where:
w 5 width of specimen in inches or millimetres to nearest 0.001 in. or 0.025 mm, respectively, and
t 5 thickness of spec
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F484-08(2019)(Test Method)
Standard Test Method for Stress Crazing of Acrylic Plastics in Contact with Liquid or Semi-Liquid Compounds

ABSTRACT
This test method covers the procedure for determining the crazing effect caused by a liquid or semi-liquid on transparent three types of acrylic plastic materials under bending stress. Cast acrylic materials from Types A and B should be annealed according to specifications while the stretched acrylic materials of Type C should not be annealed. All test specimens should be machined from polished acrylic plastic sheets and should have smooth machined surfaces.
SCOPE
1.1 This test method covers determination of the crazing effect that a liquid or semi-liquid test compound will have on transparent acrylic plastic material that is under bending stress.  
1.2 Three types of acrylic material are covered. One, two, or all of the materials shall be used in the test, as specified by the procuring agency. When not specified otherwise, all three types of acrylic shall be used in the test.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D7487-24(Practice)
Standard Practice for Polyurethane Raw Materials: Polyurethane Foam Cup Test

SIGNIFICANCE AND USE
5.1 General Utility:  
5.1.1 It is useful to verify catalyst levels in a resin blend or a polyurethane system.  
5.1.2 This practice is suitable for research, quality control, specification testing, and process control.  
5.2 Limitations:  
5.2.1 Several of the measured parameters are subjective. Therefore, operator-to-operator variability and lab-to-lab variability can be much higher than that of a single operator.  
5.2.2 The variability of this practice is dependent on the consistency of mixing of the reactants.  
5.2.3 The estimation of precision in this practice is based on typical formulations for rigid and flexible foams. Formulations with faster reaction times will likely have greater variability, particularly cream time (initiation time). Formulations with slower reaction times will likely have greater variability in the measurement of free rise time.  
5.2.4 It is possible that low-level (ppm, ppb) ingredient contamination will not be detectable using this practice. Confirmation of such contamination will potentially require large-scale (~20 L) tests and is out of the scope of this practice.
SCOPE
1.1 This practice covers the determination of cream time (initiation time), top of cup time, free rise time, free rise height, string gel time (pull time), tack free time, settle back, and free rise density of polyurethane foam formulations using a cup foam test.  
1.2 Typical definitions, terms, and techniques are described; including procedures for mixing and transferring samples to the foaming container; and data gathering and evaluation. However, agreement between the customer and the testing laboratory for all these items must be obtained prior to use.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: There is no known ISO equivalent to this standard.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D8065/D8065M-16(2023)(Specification)
Standard Classification System and Basis for Specification for Specifying Plastic Films

SIGNIFICANCE AND USE
4.1 The purpose of this classification system is to provide a method of adequately identifying plastic films using a system that applies universally for plastic films. It further provides a means for specifying these films by the use of a simple line call-out designation.  
4.2 This classification system was developed to permit the addition of additional film products and property values.  
4.3 It is intended that the classification of plastic sheeting, >0.25 mm [0.010 in.] thickness, multi-layer structures, blends, and other variants will be addressed in related standards.
SCOPE
1.1 This standard provides a classification system for tabulating the properties of unfilled, single-layer plastic films.
Note 1: The classification system serves many of the needs of industries using plastic films. The standard is subject to revision as the need requires; therefore, the latest revision should always be used.
Note 2: Film is defined in Terminology D883 as an optional term for sheeting having a nominal thickness no greater than 0.25 mm [0.010 in.].  
1.2 The classification system and subsequent line call-out (specification) is intended to be a means of identifying plastic films used for applications including industrial, packaging, construction, and agriculture. It is not intended for the selection of materials to be used in films. This selection should be made by those having expertise in the plastics field after careful consideration of the end-use requirements, the environment to which the films will be exposed, the fabrication process to be employed, the inherent properties of the material not covered in this document, and the economic factors.  
1.3 This classification system is based on the premise that plastic films can be arranged into broad generic families based on materials with similar composition using basic film properties. A system is thus established which, together with values describing additional requirements, permits as complete a description as desired of the selected film.  
1.4 In all cases where the provisions of this classification system would conflict with the referenced ASTM specification for a particular film product, the latter shall take precedence.
Note 3: It is strongly recommended that this classification system be used for all new applications and specifications and that the specification of films using existing standards be expeditiously withdrawn or converted to this classification system.  
1.5 This classification system applies to commercial products and, as such, there is no control over the manufacturing parameters employed in producing the film. It shall be the responsibility of those developing the specification documents utilizing this classification system to identify the critical parameters and values to be used for the cell classifications and suffix requirements.  
1.6 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 4: There is no known ISO equivalent to this standard.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM D6902-04(2023)(Test Method)
Standard Test Method for Laboratory Measurement of Formaldehyde Evolved During the Curing of Melamine-Formaldehyde-Based Coatings

SIGNIFICANCE AND USE
5.1 This test method measures the amount of formaldehyde that is evolved from a coating containing melamine-formaldehyde resin(s) during cure at elevated temperature. Cure formaldehyde results from a side-reaction during cross-linking of functionalized polymers with melamine-formaldehyde resins. Cure formaldehyde is evolved in the final bake or cure oven, when the coating temperature is high enough to initiate cross-linking. Formaldehyde can be released from a coating during application, solvent flash-off and cure. Free formaldehyde is primarily evolved during coating application and solvent flash-off. Test Method D1979 measures “free formaldehyde” in amino resins and Test Method D6191 measures formaldehyde evolved from coatings at ambient temperature. This method measures only the formaldehyde released during heat cure, which is primarily “cure formaldehyde.”  
5.2 This test method is not intended to duplicate the evolved formaldehyde from an industrial process, but serves as a reproducible comparative laboratory evaluation.  
5.3 This test method has not been evaluated with catalyzed coating systems that cure at or below 40 °C, such as those used by the wood-finishing industry, and would likely require special adaptation for this application.
SCOPE
1.1 This test method is for the determination of formaldehyde evolved from melamine-formaldehyde-based coatings during the cure step. The results may be used to determine the “cure formaldehyde” evolved from a sample under controlled laboratory conditions.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This test method is capable of measuring from 500 μg/g to 22 000 μg formaldehyde/g dry coating under the test conditions specified (3 000 ml/min total flow, 50 ml/min DNPH tube flow). The ratio of total flow to DNPH tube flow could be adjusted to extend the range of the method.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D4895-18(2023)(Specification)
Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From Dispersion

ABSTRACT
This specification covers dry-powder resins of polytetrafluoroethylene (PTFE) resin produced from dispersion. PTFE mixtures with additives are not covered in this specification. This specification covers type I and type II PTFE. The resins shall be tested for bulk density, particle size, water content, melting peak temperature, tensile strength, elongation at break, standard specific gravity, extrusion pressure, thermal instability index, and stretching void index. Specimen preparation, testing, inspection, and packaging shall be in accordance to the procedures indicated in this specification.
SCOPE
1.1 This specification2 covers polytetrafluoroethylene (PTFE) prepared by coagulation of a dispersion. These PTFE resins are homopolymers of tetrafluoroethylene or modified homopolymers containing not more than 1 % by weight of other fluoromonomers. The materials covered herein do not include mixtures of PTFE with additives such as colors, fillers, or plasticizers; nor do they include reprocessed or reground resin or any fabricated articles because the properties of such materials have been irreversibly changed when they were fibrillated or sintered.  
1.2 The values stated in SI units as detailed in IEEE/ASTM SI-10 are to be regarded as standard. The values given in parentheses are for information only.  
1.3 The following safety hazards caveat pertains only to the Specimen Preparation Section, Section 9, and the Test Methods Section, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Warning note in 9.1.1 for a specific hazards statement.
Note 1: Information in this specification is technically equivalent to related information in ISO 20568-1 and ISO 20568-2.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    14 pages
    English language
    sale 15% off
ASTM
ASTM D7750-23(Test Method)
Standard Test Method for Cure Behavior of Thermosetting Resins by Dynamic Mechanical Procedures using an Encapsulated Specimen Rheometer

SIGNIFICANCE AND USE
5.1 This method provides a simple means of characterizing the cure behavior of a thermosetting resin specimen that is a representation of a composite part. The diameter of the specimen is approximately 38 mm and the thickness ranges from 2.6 mm to 3.2 mm. This corresponds to a sample volume of approximately 3 cm3 to 4 cm3. The data may be used for quality control, research and development, and verifying the cure within processing equipment including autoclaves.  
5.2 Dynamic mechanical testing provides a sensitive method for determining cure characteristics by measuring the elastic and loss moduli as a function of temperature or time, or both. Plots of cure behavior and tan delta of a material provide graphical representation indicative of cure behavior under a specified time-temperature profile. The presence of fibers within the resin may change the dynamic properties measured within a material. However, it is still possible to compare different resins with the same fiber structure and obtain the relative difference due to the resin cure properties.  
5.3 This method can be used to assess the following:  
5.3.1 Cure behavior, as well as changes as a function of temperature or time, or both,  
5.3.2 Processing behavior, as well as changes as a function of temperature or time, or both,  
5.3.3 The effects of processing treatments,  
5.3.4 Relative resin behavioral properties, including cure behavior, damping and impact resistance,  
5.3.5 The effects of reinforcement on cure; the reinforcement can be a fiber or a filler,  
5.3.6 The effects of materials used to bond the resin and reinforcement,  
5.3.7 The effect of formulation additives that might affect processability or performance.  
5.4 This provides a method to assess the cure properties of a thermosetting resin containing woven fiber or other reinforcing materials.  
5.5 This method is valid for a wide range of oscillation frequencies typically from 0.002 Hz to 50 Hz.
Note 1: It is recommended tha...
SCOPE
1.1 This method covers the use of dynamic mechanical instrumentation for determination and reporting of the thermal advancement of cure behavior of thermosetting resin on an inert filler or fiber in a laboratory. It may also be used for determining the cure properties of resins without fillers or fibers. These encapsulated specimens are deformed in torsional shear using dynamic mechanical methods.  
1.2 This method is intended to provide means for determining the cure behavior of thermosetting resins on fibers over a range of temperatures from room temperature to 250 °C by forced-constant amplitude techniques (in accordance with Practice D4065). Plots of complex modulus, complex viscosity, and damping ratio or tan delta as a function of time or temperature, or both, quantify the thermal advancement or cure characteristics of a resin or a resin on filler or fiber.  
1.3 Test data obtained by this method is relevant and appropriate for optimizing cure cycles.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4.1 Exception—The Fahrenheit temperature measurement in 10.1 is provided for information only and is not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D5629-23(Test Method)
Standard Test Method for Polyurethane Raw Materials: Determination of Acidity in Low-Acidity Aromatic Isocyanates and Polyurethane Prepolymers

SIGNIFICANCE AND USE
5.1 This test method is suitable for research or for quality control to characterize aromatic isocyanates and low-acidity prepolymers. Acidity correlates with performance in some polyurethane systems.
SCOPE
1.1 This test method measures the acidity, expressed as ppm of hydrochloric acid (HCl), in aromatic isocyanate or polyurethane prepolymer samples of below 100 ppm acidity. The test method is applicable to products derived from toluene diisocyanate and methylene di(phenylisocyanate) (see Note 1). Refer to Test Method D6099 for determination of acidity in moderate- to high-acidity aromatic isocyanates.  
1.2 The values stated in SI units are to be regarded as the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: This standard is equivalent to ISO 14898, Method B.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D4661-23(Test Method)
Standard Test Methods for Polyurethane Raw Materials: Determination of Total Chlorine in Isocyanates

SIGNIFICANCE AND USE
5.1 These test methods are suitable for use for research or for quality control to determine the total chlorine content of aromatic isocyanates. In some instances total chlorine content may correlate with performance in polyurethane systems.
SCOPE
1.1 These test methods determine the total chlorine content of aromatic isocyanates used as polyurethane raw materials. The difference between the total chlorine content and the hydrolyzable chlorine content (see Test Method D4663) is a measure of the amount of chlorobenzene, o-dichlorobenzene, and other ring-substituted chlorinated products that are present. Both procedures are applicable to a variety of organic compounds but the amount of sample used is varied. (See Note 1.)  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: This standard is identical to ISO 26603.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D5991-23(Practice)
Standard Practice for Separation and Identification of Poly(Vinyl Chloride) (PVC) Contamination in Poly(Ethylene Terephthalate) (PET) Flake

SIGNIFICANCE AND USE
5.1 Presence of even low concentrations of PVC in recycled PET flakes results in equipment corrosion problems during processing. The PVC contamination level shall dictate the market for use of the recycled polymer in secondary products. Procedures presented in this practice are used to identify the PVC contamination in recycled PET flakes.
Note 4: These procedures may also be used to estimate the concentration of PVC contamination.
SCOPE
1.1 This practice covers four procedures for separation and qualitative identification of poly(vinyl chloride) (PVC) contamination in poly(ethylene terephthalate) (PET) flakes.
Note 1: Although not presented as a quantitative method, procedures presented in this practice may be used to provide quantitative results at the discretion of the user. The user assumes the responsibility to verify the reproducibility of quantitative results. Data from an independent source suggest a PVC detection level of 200 ppm (w/w) based on an original sample weight of 454 g.  
1.2 Procedure A is based on different fluorescence of PVC and PET when these polymers are exposed to ultraviolet (UV) light.  
1.3 Procedure B is an oven test based upon the charring of PVC when it is heated in air at 235°C.  
1.4 Procedures C and D are dye tests based on differential staining of PVC and PET.  
Note 2: Other polymers (for example, PETG) also absorb the stain or brightener. Such interferences will result in false positive identification of PVC as the contaminant.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazards see Section 8.  
Note 3: There is no known ISO equivalent to this standard.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D3644-15(2022)(Test Method)
Standard Test Method for Acid Number of Styrene-Maleic Anhydride Resins

SIGNIFICANCE AND USE
4.1 This test method is used to determine the property of styrene-maleic anhydride resins functionality. Acid functionality determines the utility of resin as well as being a significant quality control test.  
4.2 Because some of the anhydride functionality has been hydrolyzed in the manufacturing process, direct titration with base will produce erroneous data on the total acid content of the fully hydrolyzed resin in use. This test method charges excess alkali to hydrolize the anhydride functionality and neutralize the resulting acid. The remaining unreacted alkali is then back titrated with a standardized acid solution and the acid content is determined by difference.
SCOPE
1.1 This test method covers the measurement of the free acidity present in styrene-maleic anhydride resins.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off