ASTM F2019-03

Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic (GRP) Cured-in-Place Thermosetting Resin Pipe (CIPP)

SIGNIFICANCE AND USE
This practice is for use by designers and specifiers, regulatory agencies, owners and inspection organizations who are involved in the rehabilitation of conduits through the use of a resin-impregnated fabric tube, pulled in place through an existing conduit and subsequently inflated and cured. As for any standard practice, modifications may be required for specific job conditions.
SCOPE
1.1 This practice covers the procedures for the reconstruction of pipelines and conduits (4 to 48 in. (100 to 1200 mm) diameter) by the pulled-in place installation of a resin-impregnated, flexible fabric tube into an existing conduit followed by inflation with compressed air (see ). The resin/fabric tube is cured by flow through the fabric tube of mixed air and steam. When cured, the finished cured-in-place pipe will be continuous and tight fitting. This reconstruction process can be used in a variety of gravity flow applications such as sanitary sewers, storm sewers, process piping, electrical conduits and ventilation systems.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for informational purposes only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 09-Sep-2003
• ICS: 23.040.20 - Plastics pipes
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.67 - Trenchless Plastic Pipeline Technology

Relations

• Replaces: ASTM F2019-00 - Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic (GRP) Cured-in-Place Thermosetting Resin Pipe (CIPP)
• Effective Date: 10-Sep-2003
• Replaced By: ASTM F2019-03(2009) - Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic (GRP) Cured-in-Place Thermosetting Resin Pipe (CIPP)
• Effective Date: 01-Aug-2009
• Referred By: ASTM F3240-19e1 - Standard Practice for Installation of Seamless Molded Hydrophilic Gaskets (SMHG) for Long-Term Watertightness of Cured-in-Place Rehabilitation of Main and Lateral Pipelines
• Effective Date: 10-Sep-2003
• Referred By: ASTM D5813-04(2018) - Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems
• Effective Date: 10-Sep-2003
• Referred By: ASTM F3095-17a(2022) - Standard Practice for Laser Technologies for Direct Measurement of Cross Sectional Shape of Pipeline and Conduit by Rotating Laser Diodes and CCTV Camera System
• Effective Date: 10-Sep-2003
• Referred By: ASTM F3541-22 - Standard Practice for Sectional Repair of Existing Gravity Flow, Non-Pressure Pipelines and Conduits by Pushed or Pulled-In-Place Installation of Cured-In-Place Thermosetting Resin Pipe (CIPP)
• Effective Date: 10-Sep-2003

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation:F2019–03
Standard Practice for
Rehabilitation of Existing Pipelines and Conduits by the
Pulled in Place Installation of Glass Reinforced Plastic
1
(GRP) Cured-in-Place Thermosetting Resin Pipe (CIPP)
This standard is issued under the fixed designation F 2019; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D 1682 Test Method for Breaking Load and Elongation of
3
Textile Fabrics
1.1 This practice covers the procedures for the reconstruc-
D 3039/D 3039M Test Method for Tensile Properties of
tion of pipelines and conduits (4 to 48 in. (100 to 1200 mm)
Polymer Matrix Composite Materials
diameter) by the pulled-in place installation of a resin-
D 3567 Practice for Determining Dimensions of Reinforced
impregnated, flexible fabric tube into an existing conduit
Thermosetting Resin Pipe (RTRP) and Fittings
followed by inflation with compressed air (see Fig. 1). The
D 5813 Specification for Cured-in-Place Thermosetting
resin/fabric tube can be cured by either the flow through the
Resin Sewer Pipe
fabrictubeofmixedairandsteamorbyuseofultravioletlight.
F 412 Terminology Relating to Plastic Piping Systems
When cured, the finished cured-in-place pipe will be continu-
F 1216 Practice for Rehabilitation of Existing Pipelines and
ous and tight fitting.This reconstruction process can be used in
Conduits by the Inversion and Curing of a Resin-
a variety of gravity flow applications such as sanitary sewers,
Impregnated Tube
storm sewers, process piping, electrical conduits, ventilation
F 1417 Test Method for Installation Acceptance of Gravity
systems, and pressure applications.
Plastic Sewer Lines Using Low Pressure Air Testing
1.2 The values stated in inch-pound units are to be regarded
F 1743 Practice for Rehabilitation of Existing Pipelines and
as the standard. The values given in parentheses are for
Conduits by Pulled- in-Place Installation of Cured-in Place
informational purposes only.
Thermosetting Resin Pipe (CIPP)
1.3 This standard does not purport to address all of the
2.2 AWWA Standard:
safety concerns, if any, associated with its use. It is the
4
Manual on Cleaning and Lining Water Mains, M28
responsibility of the user of this standard to establish appro-
2.3 NASSCO Standard:
priate safety and health practices and determine the applica-
Recommended Specifications for Sewer Collection System
bility of regulatory limitations prior to use.
5
Rehabilitation
2. Referenced Documents
3. Terminology
2
2.1 ASTM Standards:
3.1 General:
D 543 TestingMethodofResistanceofPlasticstoChemical
3.1.1 DefinitionsareinaccordancewithTerminologyF 412.
Reagents
Abbreviations are in accordance with Abbreviations D 1600,
D 578 Specifications for Glass Fiber Strands
unless otherwise indicated.
D 638 Testing Method for Tensile Properties of Plastics
3.2 Definitions of Terms Specific to This Standard:
D 790 TestMethodsforFlexuralPropertiesofUnreinforced
3.2.1 calibration hose—an impermeable bladder installed
and Reinforced Plastics and Electrical Insulating Materials
inside the fabric tube, and inflated with air or steam, or both to
D 1600 Terminology for Abbreviated Terms Relating to
press the tube firmly against the wall of the existing pipe until
Plastics
the resin is cured with air and steam or ultraviolet light. The
calibration hose is removed when the installation is finished.
1 3.2.2 cured-in-place pipe (CIPP)—a hollow cylinder con-
This practice is under the jurisdiction of ASTM Committee F17 on Plastic
sisting of a glass reinforced plastic (GRP) fabric tube with
Piping Systems and is the direct responsibility of Subcommittee F17.67 on
Trenchless Plastic Pipeline Technology.
Current edition approved Sept. 10, 2003. Published November 2003.
Originally approved in 2000. Last previous edition approved in 2000 as
3
F 2019 – 00. Withdrawn.
2 4
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available fromAmerican Water WorksAssociation (AWWA), 1401 New York
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Ave., NW, Suite 640, Washington, DC 20005.
5
Standards volume information, refer to the standard’s Document Summary page on Available from National Association of Sewer Service Companies, 423 W.
the ASTM website. King Street, Suite 3000, Chambersburg, PA 17201
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F2019–03
FIG. 1 Cured-In-Place Pipe Installation Method (Air/Steam)
cured thermosetting resin. External foils are
...