ASTM F1077-95a(2002)

Standard Guide for Selection of Committee F16 Fastener Specifications

SCOPE
1.1 This guide is intended to provide a rapid, easy to use method for identifying Committee F16 fastener specifications and their applicable marking requirements. Selection is made by product type (bolts, nuts, washers, etc.) and material (alloy steel, carbon steel, stainless steel, etc.) from Tables 1-5 as follows: Table Number Inch MetricFerrous Metals  Alloy Steel13Carbon Steel13Weathering Steel1 3Non Ferrous Aluminum, CopperNickel, Titanium 2 3Stainless Steels 2  3 OthersCoatings, Definitions,Test Methods, Surface4 4Discontinuities  Marking 5 5
1.2 Table size limitations and the need for simplicity prohibit identifying the exact grade, type, condition, etc., for all product/material combinations. The product specification must be reviewed prior to specifying fasteners on drawings or ordering to properly and completely identify the fastener, and its available variations.

General Information

• Status: Historical
• Publication Date: 09-Oct-2002
• ICS: 21.060.10 - Bolts, screws, studs
• Technical Committee: F16 - Fasteners
• Drafting Committee: F16.91 - Editorial

Relations

• Replaces: ASTM F1077-95a - Standard Guide for Selection of Committee F-16 Fastener Specifications
• Effective Date: 10-Oct-2002
• Replaced By: ASTM F1077-05 - Standard Guide for Selection of Committee F16 Fastener Specifications (Withdrawn 2014)
• Effective Date: 01-Jan-2005
• Referred By: ASTM F2225-15(2020) - Standard Safety Specification for Consumer Trampoline Enclosures
• Effective Date: 10-Oct-2002
• Referred By: ASTM F1918-21 - Standard Safety Performance Specification for Soft Contained Play Equipment
• Effective Date: 10-Oct-2002
• Referred By: ASTM F2373-11(2017) - Standard Consumer Safety Performance Specification for Public Use Play Equipment for Children 6 Months through 23 Months
• Effective Date: 10-Oct-2002

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F 1077 – 95a (Reapproved 2002)
Standard Guide for
Selection of Committee F16 Fastener Specifications
This standard is issued under the fixed designation F 1077; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope A 354 Specification for Quenched and Tempered Alloy
Steel Bolts, Studs, and Other Externally Threaded Fasten-
1.1 This guide is intended to provide a rapid, easy to use
ers
method for identifying Committee F16 fastener specifications
A 394 Specification for Steel Transmission Tower Bolts,
and their applicable marking requirements. Selection is made
Zinc-Coated and Bare
by product type (bolts, nuts, washers, etc.) and material (alloy
A 449 Specification for Quenched and Tempered Steel
steel, carbon steel, stainless steel, etc.) from Tables 1-5 as
Bolts and Studs
follows:
A 489 Specification for Carbon Steel Lifting Eyes
Table Number
A 490 Specification for Structural Bolts, Alloy Steel, Heat
Inch Metric
Treatment, 150 ksi Minimum Tensile Strength
Ferrous Metals
A 490M Specification for High-Strength Steel Bolts,
Alloy Steel 1 3
Classes 10.9 and 10.9.3, for Structural Steel Joints [Met-
Carbon Steel 1 3
Weathering Steel 1 3
ric]
Non Ferrous
A 502 Specification for Steel Structural Rivets
Aluminum, Copper 23
Nickel, Titanium A 563 Specification for Carbon and Alloy Steel Nuts
Stainless Steels 2 3
A 563M Specification for Carbon and Alloy Steel Nuts
Others
[Metric]
Coatings, Definitions,
Test Methods, Surface 4 4 A 574 Specification for Alloy Steel Socket-Head Cap
Discontinuities
Screws
Marking 5 5
A 574M Specification for Alloy Steel Socket-Head Cap
Screws [Metric]
A 687 Specification for High-Strength Nonheaded Steel
1.2 Table size limitations and the need for simplicity pro-
Bolts and Studs
hibit identifying the exact grade, type, condition, etc., for all
C 514 Specification for Nails for the Application of Gyp-
product/material combinations. The product specification must
sum Board
be reviewed prior to specifying fasteners on drawings or
F 432 Specification for Roof and Rock Bolts and Accesso-
ordering to properly and completely identify the fastener, and
ries
its available variations.
F 436 Specification for Hardened Steel Washers
F 436M Specification for Hardened SteelWashers [Metric]
2. Referenced Documents
F 467 Specification for Nonferrous Nuts for General Use
2.1 ASTM Standards:
F 467M Specification for Nonferrous Nuts for General Use
A 31 Specification for Steel Rivets and Bars for Rivets,
[Metric]
Pressure Vessels
F 468 Specification for Nonferrous Bolts, Hex Cap Screws,
A 307 Specification for Carbon Steel Bolts and Studs,
and Studs for General Use
60 000 PSI Tensile Strength
F 468M Specification for Nonferrous Bolts, Hex Cap
A 325 Specification for Structural Bolts, Steel, Heat
Screws, and Studs for General Use [Metric]
Treated, 120/105 ksi Minimum Tensile Strength
F 541 Specification for Alloy Steel Eyebolts
A 325M Specification for High-Strength Bolts for Struc-
F 547 Terminology of Nails for Use with Wood and Wood-
tural Steel Joints [Metric]
Base Materials
F 568M SpecificationforCarbonandAlloySteelExternally
Threaded Metric Fasteners [Metric]
This guide is under the jurisdiction ofASTM Committee F16 on Fasteners and
is the direct responsibility of Subcommittee F16.91 on Editorial.
Current edition approved Oct. 10, 2002. Published July 2003. Originally
approved in 1987. Last previous edition approved in 1995 as F 1077 – 95a.
Discontinued–see 1998 Annual Book of ASTM Standards, Vol 01.08.
Annual Book of ASTM Standards, Vol 01.08.
Annual Book of ASTM Standards, Vol 04.01.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
F 1077 – 95a (2002)
TABLE 1 Alloy, Carbon, and Weathering Steels, Inch
Carbon Steel
Weathering
A
Product Alloy Steel
Steels
Low Medium Martensitic
B
Bolts :
Eye F 541 A 489
General purpose:
UTS 60K A 307 Gr A, B
UTS 120, 105, 90K A 449 Type 1 A 449 Type 2
UTS 125, 115K A 354 Gr BC
UTS 150, 140K A 354 Gr BD
Non Headed A 687
Roof and Rock F 432
Structural:
C
UTS 120, 105K A 325 Type 1 A 325 Type 3
UTS 150K A 490 Type 1 A 490 Type 2 A 490 Type 3
Transmission tower A 394 Type 0 A 394 Type 1 A 394 Type 2 A 394 Type 3
Nails:
Gypsum wallboard C 514
B
Nuts :
PL 69K A 563 Gr 0
PL 100, 90K A 563 Gr A
PL 133, 120, 116, 105K A 563 Gr B
PL 144K A 563 Gr C A 563 Gr C 3
PL 150, 135K A 563 Gr D
PL 175, 150K A 563 Gr DH
PL 175K A 563 Gr DH3
Rivets:
General purpose A 502 Gr 1
Pressure vessel A 31 Gr A A 31 Gr B
Structural A 502 Gr 1 A 502 Gr 2 A 502 Gr 3
Screws:
Hex cap A 449 Type 1 A 449 Type 2
Socket head A 574
Socket button and flat CSK F 835
Socket set F 912
Studs:
UTS 58-80K A 307 Gr C
UTS 60K A 307 Gr A, B
UTS 120, 105, 90K A 449 Type 1 A 449 Type 2
UTS 125, 115K A 354 Gr BC
UTS 150, 140K A 354 Gr BD
UTS 150K A 687
Washers:
General Purpose, Soft F 844
General Purpose, Hard F 436 F 436
Load Indicating F 959 Type 490 F 959 Type 325
Structural, Hard F 436 F 436
A
Ultimate tensile strengths (UTS) and proof loads (PL) where shown are approximations and vary with size. For break points, see applicable product specification.
B
For bolt/nut suitability guide, see (A 563 Table X 1.1.).
C
May be furnished as carbon, alloy, or carbon boron steel.
TABLE 2 Aluminum, Copper, Nickel, Titanium, and Stainless Steels (Inch)
A A A A A
Product Aluminum Copper Nickel Titanium Stainless
Bolts:
General purpose F 468 F 468 F 468 F 468 F 593
Transmission tower F 901
Nuts:
General purpose F 467 F 467 F 467 F 467 F 594
Transmission tower F 901
Rivets
Screws:
Hex cap F 468 F 468 F 468 F 468 F 593
S
...