ASTM F593-22
(Specification)Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
SIGNIFICANCE AND USE
13.1 For the purposes of determining compliance with the specified limits for properties listed in this specification, an observed value or calculated value shall be rounded in accordance with Practice E29.
SCOPE
1.1 This specification covers the requirements for stainless steel bolts, hex cap screws, and studs 0.25 to 1.50 in., inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance.
1.2 Seven groups of stainless steel alloys are covered, including fourteen austenitic, two ferritic, four martensitic, and one precipitation hardening.
Group
AlloysA
ConditionB
1
304, 305, 384, 304 L,
(CW) cold workedC
18-9LW, 302HQ, 304J3D
2
316, 316 L
(CW) cold workedC
3
321, 347
(CW) cold workedC
4
430E
(CW) cold workedC
5
410F
(H) hardened and tempered
6
431
(H) hardened and tempered
7
630
(AH) age hardened
1.3 Supplementary requirements of an optional nature are provided, applicable only when agreed upon between the manufacturer and the purchaser at the time of the inquiry and order.
1.4 Suitable nuts for use with bolts, hex cap screws, and studs included in this specification are covered by Specification F594. Unless otherwise specified, all nuts used on these fasteners shall conform to the requirements of Specification F594, shall be of the same alloy group, and shall have a specified minimum proof stress equal to or greater than the specified minimum full-size tensile strength of the externally threaded fastener.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:F593 −22
Standard Specification for
1
Stainless Steel Bolts, Hex Cap Screws, and Studs
ThisstandardisissuedunderthefixeddesignationF593;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoptionor,inthecaseofrevision,theyearoflastrevision.Anumberinparenthesesindicatestheyearoflastreapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* 1.5 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical
1.1 This specification covers the requirements for stainless
conversions to SI units that are provided for information only
steelbolts,hexcapscrews,andstuds0.25to1.50in.,inclusive,
and are not considered standard.
in nominal diameter in a number of alloys in common use and
1.6 This standard does not purport to address all of the
intended for service applications requiring general corrosion
safety concerns, if any, associated with its use. It is the
resistance.
responsibility of the user of this standard to establish appro-
1.2 Seven groups of stainless steel alloys are covered,
priate safety, health, and environmental practices and deter-
includingfourteenaustenitic,twoferritic,fourmartensitic,and
mine the applicability of regulatory limitations prior to use.
one precipitation hardening.
1.7 This international standard was developed in accor-
A B
Group Alloys Condition
dance with internationally recognized principles on standard-
C
1 304, 305, 384, 304 L, (CW) cold worked
D
ization established in the Decision on Principles for the
18-9LW, 302HQ, 304J3
C
2 316, 316 L (CW) cold worked
Development of International Standards, Guides and Recom-
C
3 321, 347 (CW) cold worked
mendations issued by the World Trade Organization Technical
E C
4 430 (CW) cold worked
F
Barriers to Trade (TBT) Committee.
5 410 (H) hardened and tempered
6 431 (H) hardened and tempered
7 630 (AH) age hardened
2. Referenced Documents
2
A
2.1 ASTM Standards:
Unless otherwise specified on the inquiry and order, the choice of an alloy from
within a group shall be at the discretion of the fastener manufacturer (see 6.1).
A262Practices for Detecting Susceptibility to Intergranular
B
See 4.2 for options.
Attack in Austenitic Stainless Steels
C
Sizes0.75in.andlargermaybehotworkedandsolutionannealed,providedthe
bolts comply with the cold worked (CW) mechanical property requirements. A276Specification for Stainless Steel Bars and Shapes
D
Whenapprovedbythepurchaser,Alloys303,303Se,orXM1maybefurnished.
A342/A342MTest Methods for Permeability of Weakly
E
When approved by the purchaser, Alloy 430F may be furnished.
F Magnetic Materials
When approved by the purchaser, Alloys 416 or 416Se may be furnished.
A380Practice for Cleaning, Descaling, and Passivation of
1.3 Supplementary requirements of an optional nature are
Stainless Steel Parts, Equipment, and Systems
provided, applicable only when agreed upon between the
A484/A484MSpecification for General Requirements for
manufacturer and the purchaser at the time of the inquiry and
Stainless Steel Bars, Billets, and Forgings
order.
A493Specification for Stainless Steel Wire and Wire Rods
1.4 Suitable nuts for use with bolts, hex cap screws, and
for Cold Heading and Cold Forging
studsincludedinthisspecificationarecoveredbySpecification
A555/A555MSpecification for General Requirements for
F594. Unless otherwise specified, all nuts used on these
Stainless Steel Wire and Wire Rods
fasteners shall conform to the requirements of Specification
A564/A564M Specification for Hot-Rolled and Cold-
F594, shall be of the same alloy group, and shall have a
Finished Age-Hardening Stainless Steel Bars and Shapes
specified minimum proof stress equal to or greater than the
A582/A582MSpecification for Free-Machining Stainless
specified minimum full-size tensile strength of the externally
Steel Bars
threaded fastener.
A751Test Methods and Practices for Chemical Analysis of
Steel Products
1
This specification is under the jurisdiction of ASTM Committee F16 on
Fasteners and is the direct responsibility of Subcommittee F16.04 on Nonferrous
2
Fasteners. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Nov. 1, 2022. Published January 2023. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1978. Last previous edition approved in 2017 as F593–17. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/F0593-22. the ASTM website.
*A Summary of Changes section appears at the end of t
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F593 − 17 F593 − 22
Standard Specification for
1
Stainless Steel Bolts, Hex Cap Screws, and Studs
This standard is issued under the fixed designation F593; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This specification covers the requirements for stainless steel bolts, hex cap screws, and studs 0.25 to 1.50 in., inclusive, in
nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance.
1.2 Seven groups of stainless steel alloys are covered, including fourteen austenitic, two ferritic, four martensitic, and one
precipitation hardening.
A B
Group Alloys Condition
C
1 304, 305, 384, 304 L, (CW) cold worked
D
18-9LW, 302HQ, 304J3
C
2 316, 316 L (CW) cold worked
C
3 321, 347 (CW) cold worked
E C
4 430 (CW) cold worked
F
5 410 (H) hardened and tempered
6 431 (H) hardened and tempered
7 630 (AH) age hardened
A
Unless otherwise specified on the inquiry and order, the choice of an alloy from within a group shall be at the discretion of the fastener manufacturer (see 6.1).
B
See 4.2 for options.
C
Sizes 0.75 in. and larger may be hot worked and solution annealed, provided the bolts comply with the cold worked (CW) mechanical property requirements.
D
When approved by the purchaser, Alloys 303, 303Se, or XM1 may be furnished.
E
When approved by the purchaser, Alloy 430F may be furnished.
F
When approved by the purchaser, Alloys 416 or 416Se may be furnished.
1.3 Supplementary requirements of an optional nature are provided, applicable only when agreed upon between the manufacturer
and the purchaser at the time of the inquiry and order.
1.4 Suitable nuts for use with bolts, hex cap screws, and studs included in this specification are covered by Specification F594.
Unless otherwise specified, all nuts used on these fasteners shall conform to the requirements of Specification F594, shall be of
the same alloy group, and shall have a specified minimum proof stress equal to or greater than the specified minimum full-size
tensile strength of the externally threaded fastener.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1
This specification is under the jurisdiction of ASTM Committee F16 on Fasteners and is the direct responsibility of Subcommittee F16.04 on Nonferrous Fasteners.
Current edition approved June 1, 2017Nov. 1, 2022. Published June 2017January 2023. Originally approved in 1978. Last previous edition approved in 20132017 as
ɛ1
F593 – 13aF593 – 17. . DOI: 10.1520/F0593-17.10.1520/F0593-22.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F593 − 22
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
A276 Specification for Stainless Steel Bars and Shapes
A342/A342M Test Methods for Permeability of Weakly Magnetic Materials
A380 Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems
A484/A484M Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings
A493 Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging
A555/A555M Specification for General Requirements for Stainless Steel Wire and
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.