ASTM B775-08
(Specification)Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe
Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe
ABSTRACT
This general specification contains the mandatory requirements to the ASTM standards listed herein for longitudinally welded piping made from nickel and nickel alloys. In case of conflict, the requirements listed in the particular product specification takes precedence over those listed here.
SCOPE
1.1 This specification contains various requirements that, with the exception of Section 5 and Section 10, are mandatory requirements to the following ASTM nickel and nickel alloy, longitudinally welded piping specifications:
Title of SpecificationASTM
Designation Welded UNS N08020, N08024, and N08026 Alloy PipeB 464 Welded Nickel-Iron-Chromium Alloy PipeB 514 Welded Nickel-Chromium-Iron-Alloy (UNS N06600,
UNS N06603, UNS N06025 and UNS N06045) PipeB 517 Welded Nickel and Nickel-Cobalt Alloy PipeB 619 UNS N08904, UNS N08925, and UNS N08926 Welded PipeB 673 UNS N08367 Welded PipeB 675 Nickel-Alloy (UNS N06625, N06219, and N08825) Welded PipeB 705 Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Welded PipeB 723 Welded Nickel (UNS N02200/UNS N02201) and Nickel
Copper Alloy (UNS N04400) PipeB 725
1.2 One or more of the test requirements of Section 5 apply only if specifically stated in the product specification or in the purchase order.
1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only the requirement of the product specification needs to be satisfied.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B775 −08
StandardSpecification for
General Requirements for Nickel and Nickel Alloy Welded
1
Pipe
This standard is issued under the fixed designation B775; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Material Safety Data Sheet (MSDS) for this product/material
as provided by the manufacturer, to establish appropriate
1.1 This specification contains various requirements that,
safety and health practices, and determine the applicability of
with the exception of Section 5 and Section 10, are mandatory
regulatory limitations prior to use.
requirements to the following ASTM nickel and nickel alloy,
2
longitudinally welded piping specifications:
2. Referenced Documents
ASTM
2
2.1 ASTM Standards:
2
Title of Specification Designation
B464 Specification for Welded UNS N08020 Alloy Pipe
Welded UNS N08020, N08024, and N08026 Alloy Pipe B464
B514 SpecificationforWeldedNickel-Iron-ChromiumAlloy
Welded Nickel-Iron-Chromium Alloy Pipe B514
Pipe
Welded Nickel-Chromium-Iron-Alloy (UNS N06600, B517
B517 Specification for Welded Nickel-Chromium-Iron-
UNS N06603, UNS N06025 and UNS N06045) Pipe
Welded Nickel and Nickel-Cobalt Alloy Pipe B619
Alloy (UNS N06600, UNS N06603, UNS N06025, and
UNS N08904, UNS N08925, and UNS N08926 Welded Pipe B673
UNS N06045) Pipe
UNS N08367 Welded Pipe B675
Nickel-Alloy (UNS N06625, N06219, and N08825) Welded B705 B619 Specification for Welded Nickel and Nickel-Cobalt
Pipe
Alloy Pipe
Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Welded Pipe B723
B673 Specification for UNS N08925, UNS N08354, and
Welded Nickel (UNS N02200/UNS N02201) and Nickel B725
Copper Alloy (UNS N04400) Pipe UNS N08926 Welded Pipe
B675 Specification for UNS N08367 Welded Pipe
1.2 One or more of the test requirements of Section 5 apply
B705 SpecificationforNickel-Alloy(UNSN06625,N06219
only if specifically stated in the product specification or in the
and N08825) Welded Pipe
purchase order.
B723 Specification for Nickel-Chromium-Molybdenum-
1.3 In case of conflict between a requirement of the product
Cobalt-Tungsten-Iron-Silicon Alloy (UNS N06333)
specification and a requirement of this general specification,
Welded Pipe
only the requirement of the product specification needs to be
B725 Specification for Welded Nickel (UNS N02200/UNS
satisfied.
N02201) and Nickel Copper Alloy (UNS N04400) Pipe
1.4 The values stated in inch-pound units are to be regarded
B880 Specification for General Requirements for Chemical
as standard. The values given in parentheses are mathematical
Check Analysis Limits for Nickel, Nickel Alloys and
conversions to SI units that are provided for information only
Cobalt Alloys
and are not considered standard.
E8 Test Methods for Tension Testing of Metallic Materials
E18 Test Methods for Rockwell Hardness of Metallic Ma-
1.5 This standard does not purport to address all of the
terials
safety concerns, if any, associated with its use. It is the
E29 Practice for Using Significant Digits in Test Data to
responsibility of the user of this standard to become familiar
Determine Conformance with Specifications
with all hazards including those identified in the appropriate
E39 Methods for Chemical Analysis of Nickel (Withdrawn
3
1995)
1
This specification is under the jurisdiction of ASTM Committee B02 on
E76 Test Methods for Chemical Analysis of Nickel-Copper
3
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
Alloys (Withdrawn 2003)
B02.07 on Refined Nickel and Cobalt and Their Alloys.
E112 Test Methods for Determining Average Grain Size
Current edition approved April 1, 2008. Published April 2008. Originally
approved in 1987. Last previous edition approved in 2002 as B775 – 02. DOI: E213 Practice for Ultrasonic Testing of Metal Pipe and
10.1520/B0775-08.
Tubing
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on The last approved version of this historical standard is referenced on
the ASTM website. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B775−08
E426 PracticeforElectromagnetic(Eddy-Current)Examina- 5.2.1 For welded pipe made with weld filler and at the
tion of Seamless and Welded Tubular Products,Austenitic option of the manufacturer, the transverse guided bend weld
Stainless Steel and Similar Alloys test may be substituted in lieu of the flattening test. Two bend
E
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B 775–02 Designation: B775 – 08
Standard Specification for
General Requirements for Nickel and Nickel Alloy Welded
1
Pipe
This standard is issued under the fixed designation B775; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification contains various requirements that, with the exception of Section 5 and Section 10, are mandatory
2
requirements to the following ASTM nickel and nickel alloy, longitudinally welded piping specifications:
ASTM
2
Title of Specification Designation
Welded UNS N08020, N08024, and N08026 Alloy PipeB 464 B464
Welded UNS N08020, N08024, and N08026 Alloy Pipe B464
Welded Nickel-Iron-Chromium Alloy PipeB 514 B514
Welded Nickel-Iron-Chromium Alloy Pipe B514
Welded Nickel-Chromium-Iron-Alloy (UNS N06600, B517
UNS N06603, UNS N06025 and UNS N06045) PipeB 517
Welded Nickel-Chromium-Iron-Alloy (UNS N06600, B517
UNS N06603, UNS N06025 and UNS N06045) Pipe
Welded Nickel and Nickel-Cobalt Alloy PipeB 619 B619
Welded Nickel and Nickel-Cobalt Alloy Pipe B619
UNS N08904, UNS N08925, and UNS N08926 Welded B673
PipeB 673
UNS N08904, UNS N08925, and UNS N08926 Welded Pipe B673
UNS N08367 Welded PipeB 675 B675
UNS N08367 Welded Pipe B675
Nickel-Alloy (UNS N06625, N06219, and N08825) Welded B705
PipeB 705
Nickel-Alloy (UNS N06625, N06219, and N08825) Welded B705
Pipe
Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Welded PipeB 723 B723
Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Welded Pipe B723
Welded Nickel (UNS N02200/UNS N02201) and Nickel B725
Copper Alloy (UNS N04400) PipeB 725
Welded Nickel (UNS N02200/UNS N02201) and Nickel B725
Copper Alloy (UNS N04400) Pipe
1.2 One or more of the test requirements of Section 5 apply only if specifically stated in the product specification or in the
purchase order.
1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only
the requirement of the product specification needs to be satisfied.
1.4The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data
Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and
determine the applicability of regulatory limitations prior to use.
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB02onNonferrousMetalsandAlloysandisthedirectresponsibilityofSubcommitteeB02.07onRefined
Nickel and Cobalt and Their Alloys.
Current edition approved Oct. 10, 2002. Published December 2002. Originally published as B 775–87. Last previous edition B 775–01.
CurrenteditionapprovedApril1,2008.PublishedApril2008.Originallyapprovedin1987.Lastpreviouseditionapprovedin2002asB775 – 02.DOI:10.1520/B0775-08.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
, Vol 02.04.volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B775 – 08
2. Referenced Documents
2
2.1 ASTM Standards:
2
B880Specification for General Requirements for Chemical CheckAnalysis Limits for Nickel, NickelAlloys and CobaltAlloys
464 Specification for Welded UNS N08020 Alloy Pipe
B514 Specification for Welded Nickel-Iron-Chromium Alloy Pipe
B517 Specification for Welded Nickel-Chromium-Iron-Alloy (UNS N06600, UNS N06603, UNS N06025, and UNS N06045)
Pipe
B619 Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe
B673 Specification for UNS N08925, UNS N08354, and UNS N08926 Welded Pipe
B675 Specification for UNS N08367 Welded Pipe
B705 Specification for Nickel-Alloy (UNS N06625, N06219 and N08825) W
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B775–02 Designation: B 775 – 08
Standard Specification for
General Requirements for Nickel and Nickel Alloy Welded
1
Pipe
This standard is issued under the fixed designation B 775; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification contains various requirements that, with the exception of Section 5 and Section 10, are mandatory
2
requirements to the following ASTM nickel and nickel alloy, longitudinally welded piping specifications:
ASTM
2
Title of Specification Designation
Welded UNS N08020, N08024, and N08026 Alloy Pipe B 464
Welded Nickel-Iron-Chromium Alloy Pipe B 514
Welded Nickel-Chromium-Iron-Alloy (UNS N06600, B 517
UNS N06603, UNS N06025 and UNS N06045) Pipe
Welded Nickel and Nickel-Cobalt Alloy Pipe B 619
UNS N08904, UNS N08925, and UNS N08926 Welded Pipe B 673
UNS N08367 Welded Pipe B 675
Nickel-Alloy (UNS N06625, N06219, and N08825) Welded B 705
Pipe
Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Welded Pipe B 723
Welded Nickel (UNS N02200/UNS N02201) and Nickel B 725
Copper Alloy (UNS N04400) Pipe
1.2 One or more of the test requirements of Section 5 apply only if specifically stated in the product specification or in the
purchase order.
1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only
the requirement of the product specification needs to be satisfied.
1.4The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data
Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and
determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
2
B880Specification for General Requirements for Chemical CheckAnalysis Limits for Nickel, NickelAlloys and CobaltAlloys
464 Specification for Welded UNS N08020, N08024, and N08026 Alloy Pipe
B 514 Specification for Welded Nickel-Iron-Chromium Alloy Pipe
B 517 Specification for Welded Nickel-Chromium-Iron-Alloy (UNS N06600, UNS N06603, UNS N06025, and UNS N06045)
Pipe
B 619 Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe
B 673 Specification for UNS N08925, UNS N08354, and UNS N08926 Welded Pipe
B 675 Specification for UNS N08367 Welded Pipe
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB02onNonferrousMetalsandAlloysandisthedirectresponsibilityofSubcommitteeB02.07onRefined
Nickel and Cobalt and Their Alloys.
Current edition approved Oct. 10, 2002. Published December 2002. Originally published as B775–87. Last previous edition B775–01.
Current edition approved April 1, 2008. Published April 2008. Originally approved in 1987. Last previous edition approved in 2002 as B 775 – 02.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
, Vol 02.04.volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B775–08
B 705 Specification for Nickel-Alloy (UNS N06625, N06219 and N08825) Welded Pipe
B 723 Specification for Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon Alloy (UNS N06333) Welded Pipe
B 725 Specification for Welded Nickel (UNS N02200/UNS N02201) and Nickel Copper Alloy (UNS N04400) Pipe
B 880 SpecificationforGeneralRequirementsforChemicalCheckAnalysisLimitsforNickel,NickelAlloysandCobaltAlloys
E 8 Test Methods for Tension Testing of Metallic Materials
3
E 18Test Methods for Rockwell Hardness and Rockwell Superficial Hardness of Metallic Materials
Test Methods for Rockwell Hardness of Metallic Materials
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.