ASTM A377-18(2022)e1

Standard Index of Specifications for Ductile Iron Pressure Pipe

SCOPE
1.1 This index identifies specifications that cover ductile iron pressure pipe suitable for carrying water and other liquids under pressure.  
Note 1: The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Published
• Publication Date: 30-Sep-2022
• ICS: 23.040.10 - Iron and steel pipes
• Technical Committee: A04 - Iron Castings
• Drafting Committee: A04.12 - Pipes and Tubes

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
´1
Designation: A377 −18 (Reapproved 2022)
Standard Index of Specifications for
Ductile Iron Pressure Pipe
This standard is issued under the fixed designation A377; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
ε NOTE—3.2 was updated editorially in October 2022.
1. Scope 3.2 Other American National Standards relating to ductile-
iron pipe are the following:
1.1 This index identifies specifications that cover ductile
ANSI/AWWA C104/A21.4, Cement-Mortar Lining for
iron pressure pipe suitable for carrying water and other liquids
2,3
Ductile-Iron Pipe and Fittings
under pressure.
ANSI/AWWA C105/A21.5, Polyethylene Encasement for
NOTE 1—The text of this standard references notes and footnotes which
2,3
Ductile-Iron Pipe Systems
provide explanatory material. These notes and footnotes (excluding those
in tables and figures) shall not be considered as requirements of the ANSI/AWWA C150/A21.50, Thickness Design of Ductile-
2,3
standard.
Iron Pipe
1.2 This international standard was developed in accor-
ANSI/AWWA C110/A21.10, Ductile-Iron and Gray-Iron
2,3
dance with internationally recognized principles on standard-
Fittings
ization established in the Decision on Principles for the
ANSI/AWWA C111/A21.11, Rubber-Gasket Joints for
Development of International Standards, Guides and Recom- 2,3
Ductile-Iron Pressure Pipe and Fittings
mendations issued by the World Trade Organization Technical
ANSI/AWWAC115/A21.15, Flanged Ductile-Iron Pipe with
Barriers to Trade (TBT) Committee.
2,3
Ductile-Iron or Gray-Iron Threaded Flanges
2. Method of Designation ANSI/AWWA C116/A21.16, Protective Fusion-Bonded
Coatings for the Interior and Exterior Surfaces of Ductile-Iron
2.1 The ASTM designation for these specifications is not
2,3
and Gray-Iron Fittings
sufficient to describe the particular items a purchaser may
ANSI/AWWA C153/A21.53, Ductile Iron Compact
desire; therefore, the ANSI designation for the applicable
2,3
Fittings
American National Standards shown in Section 3 shall be
specified in the inquiry, contract, and order. ANSI/AWWA C600, Installation of Ductile-Iron Mains and
2,3
Their Appurtenances
3. Reference Specifications
2,3
ANSI/AWWA C606, Grooved and Shouldered Joints
3.1 Ductile iron pipe furnished in accordance with this
NOTE 2—These specifications were prepared by appropriate subcom-
index are covered by the following American National Stan-
mittees ofAmerican Water WorksAssociation CommitteeA21 on Ductile
dards:
Iron Pipe and Fittings. This committee was originally organized as an
ANSI/AWWA C151/A21.51, Ductil
...