ASTM C1277-20
(Specification)Standard Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings
Standard Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings
ABSTRACT
This specification covers the materials and testing of shield hubless couplings to join hubless cast iron soil pipe and fittings. Gaskets shall comply with the required physical and chemical properties, dimensions, and material specifications. The rubber gasket shall conform to the required physical requirements such as tensile strength, elongation, durometer, accelerated aging, compression set, oil immersion, ozone cracking, tear resistance, and water absorption. The shield and clamp assembly shall be made of material conforming to the requirements such as tensile strength and hardness. All parts shall be made of 300 series stainless steel, namely: Type 301; Type 304; Type 300; Type 301; and Type 305. The material shall also undergo physical tests like deflection, shear, and unstrained hydrostatic tests.
SCOPE
1.1 This specification covers the materials and testing of shielded hubless couplings to join hubless cast iron soil pipe and fittings.
1.2 Several different types of hubless couplings are available for use in hubless cast iron sanitary and storm drain, waste, and vent piping applications to connect hubless cast iron soil pipe and fittings by using a sleeve-type, or some other type coupling device. It is the purpose of this specification to furnish information as to the characteristics of one such sleeve-type couplings when applied to cast iron soil pipe and fittings manufactured in accordance with Specification A888, latest revision, and CISPI 301, latest revision.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 The committee with jurisdiction over this standard is aware of other comparable standard published by the Cast Iron Soil Pipe Institute, CISPI 310, FM 1680 published by Factory Mutual, and Specification C1540 published by ASTM.
1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:C1277 −20
Standard Specification for
Shielded Couplings Joining Hubless Cast Iron Soil Pipe and
1
Fittings
This standard is issued under the fixed designation C1277; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2
1.1 This specification covers the materials and testing of 2.1 ASTM Standards:
shielded hubless couplings to join hubless cast iron soil pipe A240/A240M Specification for Chromium and Chromium-
and fittings. Nickel Stainless Steel Plate, Sheet, and Strip for Pressure
Vessels and for General Applications
1.2 Several different types of hubless couplings are avail-
A644 Terminology Relating to Iron Castings
able for use in hubless cast iron sanitary and storm drain,
A888 Specification for Hubless Cast Iron Soil Pipe and
waste,andventpipingapplicationstoconnecthublesscastiron
Fittings for Sanitary and Storm Drain, Waste, and Vent
soil pipe and fittings by using a sleeve-type, or some other type
Piping Applications
couplingdevice.Itisthepurposeofthisspecificationtofurnish
C564 Specification for Rubber Gaskets for Cast Iron Soil
information as to the characteristics of one such sleeve-type
Pipe and Fittings
couplings when applied to cast iron soil pipe and fittings
C1540 Specification for Heavy-Duty Shielded Couplings
manufactured in accordance with Specification A888, latest
Joining Hubless Cast Iron Soil Pipe and Fittings
revision, and CISPI 301, latest revision.
D395 Test Methods for Rubber Property—Compression Set
1.3 The values stated in inch-pound units are to be regarded
D412 Test Methods forVulcanized Rubber andThermoplas-
as standard. The values given in parentheses are mathematical
tic Elastomers—Tension
conversions to SI units that are provided for information only
D471 Test Method for Rubber Property—Effect of Liquids
and are not considered standard.
D573 Test Method for Rubber—Deterioration in an Air
1.4 The committee with jurisdiction over this standard is Oven
D624 Test Method for Tear Strength of Conventional Vul-
aware of other comparable standard published by the Cast Iron
canized Rubber and Thermoplastic Elastomers
Soil Pipe Institute, CISPI 310, FM 1680 published by Factory
Mutual, and Specification C1540 published by ASTM. D1149 Test Methods for Rubber Deterioration—Cracking in
an Ozone Controlled Environment
1.5 The following precautionary caveat pertains only to the
D2240 Test Method for Rubber Property—Durometer Hard-
test method portion, Section 7, of this specification. This
ness
standard does not purport to address all of the safety concerns,
D3677 Test Methods for Rubber—Identification by Infrared
if any, associated with its use. It is the responsibility of the user
Spectrophotometry
of this standard to establish appropriate safety, health, and
3
environmental practices and determine the applicability of
2.2 CISPI Standards:
regulatory limitations prior to use. CISPI 301 Specification for Hubless Cast Iron Soil Pipe and
1.6 This international standard was developed in accor-
Fittings for Sanitary and Storm Drain, Waste, and Vent
dance with internationally recognized principles on standard- Piping Applications
ization established in the Decision on Principles for the CISPI 310 Specification for Couplings for Use in Connec-
Development of International Standards, Guides and Recom- tion with Hubless Cast Iron Soil Pipe and Fittings for
mendations issued by the World Trade Organization Technical Sanitary and Storm Drain, Waste, and Vent Piping Appli-
Barriers to Trade (TBT) Committee. cations
1 2
This specification is under the jurisdiction of ASTM Committee A04 on Iron For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Castings and is the direct responsibility of Subcommittee A04.75 on Gaskets and contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Coupling for Plumbing and Sewer Piping. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved May 1, 2020. Published May 2020. Originally the ASTM website.
3
approved in 1994. Last previous edition approved in 2018 as C1277 – 18. DOI: Available from Cast Iron Soil Pipe Institute (CISPI), 2401 Fieldcrest Dr.,
10.1520/C1277-20. Mundelein, IL 60060, http://www.cispi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1277−20
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1277 − 18 C1277 − 20
Standard Specification for
Shielded Couplings Joining Hubless Cast Iron Soil Pipe and
1
Fittings
This standard is issued under the fixed designation C1277; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers the materials and testing of shielded hubless couplings to join hubless cast iron soil pipe and
fittings.
1.2 Several different types of hubless couplings are available for use in hubless cast iron sanitary and storm drain, waste, and
vent piping applications to connect hubless cast iron soil pipe and fittings by using a sleeve-type, or some other type coupling
device. It is the purpose of this specification to furnish information as to the characteristics of one such sleeve-type couplings when
applied to cast iron soil pipe and fittings manufactured in accordance with Specification A888, latest revision, and CISPI-301,
CISPI 301, latest revision.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 The committee with jurisdiction over this standard is aware of other comparable standard published by the Cast Iron Soil
Pipe Institute, CISPI-310, CISPI 310, FM 1680 published by Factory Mutual, and Specification C1540 published by ASTM.
1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory
limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and
for General Applications
A644 Terminology Relating to Iron Castings
A888 Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping
Applications
C564 Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings
C1540 Specification for Heavy-Duty Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings
D395 Test Methods for Rubber Property—Compression Set
D412 Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
D471 Test Method for Rubber Property—Effect of Liquids
D573 Test Method for Rubber—Deterioration in an Air Oven
D624 Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers
D1149 Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment
D2240 Test Method for Rubber Property—Durometer Hardness
1
This specification is under the jurisdiction of ASTM Committee A04 on Iron Castings and is the direct responsibility of Subcommittee A04.75 on Gaskets and Coupling
for Plumbing and Sewer Piping.
Current edition approved Feb. 1, 2018May 1, 2020. Published February 2018May 2020. Originally approved in 1994. Last previous edition approved in 20152018 as
C1277 – 15.C1277 – 18. DOI: 10.1520/C1277-18.10.1520/C1277-20.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1277 − 20
D3677 Test Methods for Rubber—Identification by Infrared Spectrophotometry
3
2.2 CISPI Standards:
CISPI-301 CISPI 301 Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent
Piping Applications
CISPI-310 CISPI 310 Specification for Couplings for Use in Conne
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.