iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F645-18

(Guide)

Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems

Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems

SIGNIFICANCE AND USE
4.1 The requirements of this specification are intended to provide information to select, design and install thermoplastic, water-pressure piping systems for use outside buildings. Materials covered in this specification are Poly(Vinyl Chloride) (PVC) and Polyethylene (PE) plastic pipe fittings.
SCOPE
1.1 This guide is intended for use in the selection, design, and installation of thermoplastic water systems for use outside buildings. For specific projects, a thorough review of this guide is recommended for the purpose of selecting specific materials, methods of joining, system design factor, and any special procedures deemed necessary to assure a satisfactory system.  
Note 1: Comprehensive information on the selection, design, joining, system design factors, installation and special products and piping systems for pressurized water and other specialized applications is available in the PPI Handbook of Polyethylene Pipe and from other domestic and International sources such as PE compound and product manufacturers and trade associations.  
1.2 It is recommended that governing codes and project specifications be consulted prior to the use of this guide. Nothing in this guide should be construed as recommending practices or systems at variance with governing codes and project specifications.  
1.3 The pipe, fittings, and joining materials shall meet the requirements of one or more of the following component product standards listed in 1.3.1 through 1.3.4 to the extent applicable. In 1.3.1, 1.3.2, and 1.3.4 the pipe standards followed by (a) are outside diameter-controlled pipes.  
1.3.1 For poly(vinyl chloride) (PVC) plastic piping components:      
Title of Specification  
ASTM
Designation  
Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80
and 120 (a)  
D1785    
Poly(Vinyl Chloride) (PVC) Plastic Pipe (SDR-PR) (a)  
D2241    
Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings,
Schedule 80  
D2464    
Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule
40  
D2466  
Socket-Type Poly(Vinyl Chloride) (PVC) Plastic Pipe
Fittings, Schedule 80  
D2467  
Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Pipe
and Fittings  
D2564  
Bell-End Poly(Vinyl Chloride) (PVC) Pipe (a)  
D2672    
Poly(Vinyl Chloride) (PVC) Plastic Tubing (a)  
D2740    
Socket-Type Poly(Vinyl Chloride) (PVC) Plastic Line
Couplings  
D3036    
Joints for Plastic Pressure Pipes Using Flexible Elastomeric
Seals  
D3139    
Elastomeric Seals (Gaskets) for Joining Plastic Pipe  
F477    
PVC and ABS Injected Solvent Cemented Plastic Pipe
Joints  
F545  
1.3.2 For Chlorinated Poly(Vinyl chloride) (CPVC) plastic piping components:      
Title of Specification  
ASTM
Designation  
Chlorinated Poly(Vinyl chloride) (CPVC) Plastic Pipe, Schedules 40 and 80 (a)  
F441/F441M  
Chlorinated Poly(Vinyl chloride) (CPVC) Plastic Pipe Fittings, Schedule 80  
F439  
Solvent Cements for Chlorinated Poly(Vinyl chloride) (CPVC) Plastic Pipe and Fittings  
F493  
1.3.3 Standards for polyethylene (PE) plastic piping:      
ASTM Standards  
Designation  
Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter  
D2239  
Standard Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe  
D2609  
Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing  
D2683  
Standard Specification for Polyethylene (PE) Plastic Tubing  
D2737  
Standard Practice for Underground Installation of Thermoplastic Pressure Piping  
D2774  
Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing  
D3261  
Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter  
D3035  
Stan...

General Information

Status
Historical
Publication Date
31-Dec-2017
ICS
23.040.20 - Plastics pipes
Technical Committee
F17 - Plastic Piping Systems
Drafting Committee
F17.61 - Water
Current Stage
Ref Project

Relations

Replaces
ASTM F645-15a - Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems
Effective Date
01-Jan-2018
Replaced By
ASTM F645-18a - Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems
Effective Date
01-Mar-2018
Referred By
ASTM D2846/D2846M-19a - Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water Distribution Systems
Effective Date
01-Jan-2018
Referred By
ASTM F1668-16(2022) - Standard Guide for Construction Procedures for Buried Plastic Pipe
Effective Date
01-Jan-2018
Referred By
ASTM F412-23 - Standard Terminology Relating to Plastic Piping Systems
Effective Date
01-Jan-2018

Buy Standard

ASTM F645-18 - Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping SystemsASTM F645-18 - Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems
PreviousNext
Guide
ASTM F645-18 - Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems
English language
13 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM F645-18 - Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping SystemsREDLINE ASTM F645-18 - Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems
PreviousNext
Guide
REDLINE ASTM F645-18 - Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems
English language
13 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F645 − 18 An American National Standard
Standard Guide for
Selection, Design, and Installation of Thermoplastic Water-
1
Pressure Piping Systems
ThisstandardisissuedunderthefixeddesignationF645;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoptionor,inthecaseofrevision,theyearoflastrevision.Anumberinparenthesesindicatestheyearoflastreapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
Bell-End Poly(Vinyl Chloride) (PVC) Pipe (a) D2672
Poly(Vinyl Chloride) (PVC) Plastic Tubing (a) D2740
1.1 This guide is intended for use in the selection, design,
Socket-Type Poly(Vinyl Chloride) (PVC) Plastic Line D3036
and installation of thermoplastic water systems for use outside Couplings
Joints for Plastic Pressure Pipes Using Flexible Elastomeric D3139
buildings.Forspecificprojects,athoroughreviewofthisguide
Seals
isrecommendedforthepurposeofselectingspecificmaterials,
Elastomeric Seals (Gaskets) for Joining Plastic Pipe F477
methods of joining, system design factor, and any special PVC and ABS Injected Solvent Cemented Plastic Pipe F545
Joints
procedures deemed necessary to assure a satisfactory system.
1.3.2 For Chlorinated Poly(Vinyl chloride) (CPVC) plastic
NOTE 1—Comprehensive information on the selection, design, joining,
piping components:
systemdesignfactors,installationandspecialproductsandpipingsystems
for pressurized water and other specialized applications is available in the Title of Specification ASTM
Designation
PPI Handbook of Polyethylene Pipe and from other domestic and
Chlorinated Poly(Vinyl chloride) (CPVC) Plastic Pipe, F441/F441M
International sources such as PE compound and product manufacturers
Schedules 40 and 80 (a)
and trade associations.
Chlorinated Poly(Vinyl chloride) (CPVC) Plastic Pipe Fittings, F439
1.2 It is recommended that governing codes and project Schedule 80
Solvent Cements for Chlorinated Poly(Vinyl chloride) (CPVC) F493
specifications be consulted prior to the use of this guide.
Plastic Pipe and Fittings
Nothing in this guide should be construed as recommending
1.3.3 Standards for polyethylene (PE) plastic piping:
practices or systems at variance with governing codes and
ASTM Standards Designation
project specifications.
Standard Specification for Polyethylene (PE) Plastic Pipe D2239
1.3 The pipe, fittings, and joining materials shall meet the (SIDR-PR) Based on Controlled Inside Diameter
Standard Specification for Plastic Insert Fittings for Polyeth- D2609
requirements of one or more of the following component
ylene (PE) Plastic Pipe
product standards listed in 1.3.1 through 1.3.4 to the extent
Standard Specification for Socket-Type Polyethylene Fittings D2683
applicable. In 1.3.1, 1.3.2, and 1.3.4 the pipe standards fol- for Outside Diameter-Controlled Polyethylene Pipe and Tub-
ing
lowed by (a) are outside diameter-controlled pipes.
Standard Specification for Polyethylene (PE) Plastic Tubing D2737
1.3.1 For poly(vinyl chloride) (PVC) plastic piping compo-
Standard Practice for Underground Installation of Thermo- D2774
nents: plastic Pressure Piping
Standard Specification for Butt Heat Fusion Polyethylene D3261
ASTM
(PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and
Title of Specification Designation
Tubing
Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80 D1785
Standard Specification for Polyethylene (PE) Plastic Pipe D3035
and 120 (a)
(DR-PR) Based on Controlled Outside Diameter
Poly(Vinyl Chloride) (PVC) Plastic Pipe (SDR-PR) (a) D2241
Standard Specification for Polyethylene (PE) Plastic Pipe F714
Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, D2464
(DR-PR) Based on Outside Diameter
Schedule 80
Standard Specification for Electrofusion Type Polyethylene F1055
Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule D2466
Fittings for Outside Diameter Controlled Polyethylene and
40
Crosslinked Polyethylene (PEX) Pipe and Tubing
Socket-Type Poly(Vinyl Chloride) (PVC) Plastic Pipe D2467
Standard Specification for Socket Fusion Tools for Use in F1056
Fittings, Schedule 80
Socket Fusion Joining Polyethylene Pipe or Tubing and Fit-
Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Pipe D2564
tings
and Fittings
Standard Practice for Electrofusion Joining Polyolefin Pipe F1290
and Fittings
Standard Specification for Deformed Polyethylene (PE) F1533
Liner
1
Standard Guide for Construction Procedures for Buried F1668
This guide is under the jurisdiction ofASTM Committee F17 on Plastic Piping
Plastic Pipe
Systems and is the direct responsibility of Subcommittee F17.61 on Water.
Standard Practice for Field Leak Testing of Polyethylene F2164
Current edition approved Jan. 1, 2018. Published April 2018. Originally
(PE) and Crosslinked Polyethylene (PEX) Pressure Piping
approved in 1980. Last previous edition appro
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F645 − 15a F645 − 18 An American National Standard
Standard Guide for
Selection, Design, and Installation of Thermoplastic Water-
1
Pressure Piping Systems
This standard is issued under the fixed designation F645; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This guide is intended for use in the selection, design, and installation of thermoplastic water systems for use outside
buildings. For specific projects, a thorough review of this guide is recommended for the purpose of selecting specific materials,
methods of joining, system design factor, and any special procedures deemed necessary to assure a satisfactory system.
NOTE 1—Comprehensive information on the selection, design, joining, system design factors, installation and special products and piping systems for
pressurized water and other specialized applications is available in the PPI Handbook of Polyethylene Pipe and from other domestic and International
sources such as PE compound and product manufacturers and trade associations.
1.2 It is recommended that governing codes and project specifications be consulted prior to the use of this guide. Nothing in
this guide should be construed as recommending practices or systems at variance with governing codes and project specifications.
1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated
in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values
from the two systems may result in non-conformance with the standard. The pipe, fittings, and joining materials shall meet the
requirements of one or more of the following component product standards listed in 1.3.1 through 1.3.4 to the extent applicable.
ThoseIn 1.3.1, 1.3.2, and 1.3.4 the pipe standards followed by (a) are outside diameter-controlled pipes. Those followed by (b) are
inside diameter-controlled pipes.
1.3.1 For poly(vinyl chloride) (PVC) plastic piping components:
ASTM
Title of Specification Designation
Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80 D1785
and 120 (a)
Poly(Vinyl Chloride) (PVC) Plastic Pipe (SDR-PR) (a) D2241
Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, D2464
Schedule 80
Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule D2466
40
Socket-Type Poly(Vinyl Chloride) (PVC) Plastic Pipe D2467
Fittings, Schedule 80
Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Pipe D2564
and Fittings
Bell-End Poly(Vinyl Chloride) (PVC) Pipe (a) D2672
Poly(Vinyl Chloride) (PVC) Plastic Tubing (a) D2740
Socket-Type Poly(Vinyl Chloride) (PVC) Plastic Line D3036
Couplings
Joints for Plastic Pressure Pipes Using Flexible Elastomeric D3139
Seals
Elastomeric Seals (Gaskets) for Joining Plastic Pipe F477
PVC and ABS Injected Solvent Cemented Plastic Pipe F545
Joints
1.3.2 For Chlorinated Poly(Vinyl chloride) (CPVC) plastic piping components:
Title of Specification ASTM
Designation
Chlorinated Poly(Vinyl chloride) (CPVC) Plastic Pipe, Schedules 40 and 80 (a) F441/F441M
Chlorinated Poly(Vinyl chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 F439
Solvent Cements for Chlorinated Poly(Vinyl chloride) (CPVC) Plastic Pipe and Fittings F493
1
This guide is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.61 on Water.
Current edition approved May 15, 2015Jan. 1, 2018. Published July 2015April 2018. Originally approved in 1980. Last previous edition approved in 2015 as
F645 – 15.F645 – 15a. DOI: 10.1520/F0645-15A.10.1520/F0645-18.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F645 − 18
1.3.3 For Standards for polyethylene (PE) plastic piping components: piping:
Title of Specification ASTM
Designation
Polyethylene (PE) Plastic Pipe, (SDR-PR) (b) D2239
Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe D2609
Socket-Type Polyethylene Fittings for Outside Diameter- D2683
Controlled Polyethylene Pipe (a)
Polyethylene (PE) Plastic Tubing (a) D2737
Polyethylene (PE) Plastic Pipe (SDR-PR) Based on D3035
Controlled Out
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D2152-23(Test Method)
Standard Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by Acetone Immersion

SIGNIFICANCE AND USE
3.1 This test method is applicable only for distinguishing between inadequately fused and adequately fused PVC. The difference between thermally degraded and adequately fused PVC cannot be detected by this test method. Acetone immersion testing is not a substitute for burst, impact, or other physical or chemical tests on PVC pipe or fittings and it, therefore, shall not be used as the only test specification for purchasing of PVC pipe and fittings. This test method only detects inadequate fusion and does not determine the over-all quality of the PVC pipe or fittings.  
3.2 This test method is useful in determining whether inadequate fusion contributed to failure of PVC pipe or fittings in other physical or chemical tests, or in service.  
3.3 This test method is useful in evaluating the adequacy of PVC fusion obtained in process or materials trials.  
3.4 This test method determines adequacy of fusion on a single, relatively small specimen. This test method requires the use of a hazardous reagent which must be properly handled and disposed. Therefore, this test method may not be cost-effective to employ as a routine quality control test.
SCOPE
1.1 This test method covers the determination of the adequacy of fusion of extruded rigid poly(vinyl chloride) (PVC) pipe and molded fittings as indicated by reaction to immersion in anhydrous acetone.  
1.2 The values stated in inch-pound units are to be regarded as the standard except where instruments are calibrated in SI units.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.Specific hazards statements are given in Annex A1.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F1563-23(Specification)
Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing

ABSTRACT
This specification covers the physical requirements for tools used to squeeze-off polyethylene gas pipe and tubing. The squeeze bars shall be of a size and configuration that compresses the pipe walls to reduce the gas flow, but does not damage the pipe and may be configured as round (circular), flat with rounded edges, two round bars side by side, or any other configuration. The tool shall have the following requirements: mechanical, hydraulic, or pneumatic force mechanisms; resistance to damage or deformation; release protection; release rate; flow control; and grounding. It shall also have sufficient squeeze bar length and spacing to allow the maximum diameter pipe to be centered between the guides and mechanical stops to provide protection for over squeezing.
SCOPE
1.1 This specification covers the physical requirements for tools used to squeeze-off polyethylene (PE) pipe and tubing. It is limited to squeeze-off procedures set forth by the pipe manufacturer as referred to in Specification D2513 for gas pressure pipe systems.  
1.2 Nothing in this specification shall be construed as recommending practices or systems at variances with governing codes and project specifications.  
1.3 Where applicable in this specification, “pipe” shall mean “pipe and tubing,” and “tool” shall mean “squeeze-off tool.”  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following safety hazards caveat pertains only to the test methods portions, Section 5 and Appendix X1 of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM F2945-18(2023)(Specification)
Standard Specification for Polyamide 11 Gas Pressure Pipe, Tubing, and Fittings

ABSTRACT
This specification covers requirements and test methods for the characterization of polyamide 11 pipe, tubing, and fittings for use in fuel gas piping. The pipe and fittings covered by this specification are intended for use in the transport of fuel gases. This specification does not cover threaded pipe. The polyamide 11 material used to make pipe and fittings shall be virgin or reworked material and shall have a Plastics Pipe Institute (PPI) long-term hydrostatic design stress and hydrostatic design basis rating as determined per PPI TR3 and PPI TR4. This specification deals with requirements for materials, requirements for pipe and fittings, test methods, marking, and quality Assurance.
SCOPE
1.1 This specification covers requirements and test methods for the characterization of polyamide 11 pipe, tubing, and fittings for use in fuel gas pipelines. The pipe and fittings covered by this specification are intended for use in the distribution and transmission of fuel gases.  
1.1.1 This specification does not cover threaded pipe. Generic fusion guidelines are given in Appendix X1. Design considerations are discussed in Appendix X2. In-plant quality control programs are specified in Annex A1.  
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
Note 1: Heat fusion joining of PA11 pipe and fittings meeting the requirements of this standard is limited to PA11 pipe and fittings meeting the requirements of this standard. Heat Fusion joining of PA11 pipe and fittings meeting the requirements of this standard is not allowed to pipes and fittings made from any other thermoplastic materials (for example, PA12, PEs, PVCs, etc.).  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following is an index of the annexes and appendixes in this specification:    
Annexes  
Subject  
Annex A1  
In-Plant Quality Control for sizes up to 12 in.  
Annex A2  
PA-11 Butt Fusion Fittings  
Appendixes  
Subject  
Appendix X1  
Butt Fusion Guidelines for PA-11 Piping  
Appendix X2  
Design Consideration  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    15 pages
    English language
    sale 15% off
ASTM
ASTM F891-23(Specification)
Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe With a Cellular Core

ABSTRACT
This specification covers coextruded poly(vinyl chloride) plastic pipe with a cellular core and concentric inner and outer solid layers. The pipe is produced using a multilayer coextrusion die for nonpressure use in three series: an IPS Schedule 40 series; a PS series with an iron pipe size outside diameter with varying wall thickness as required for pipe stiffness of 25, 50, and 100; and a sewer and drain series. The pipe shall comply with the minimum wall thickness, outside diameter, length, stiffness, flattening, impact strength, bond strength, and extrusion quality requirements.
SCOPE
1.1 This specification covers coextruded poly(vinyl chloride) (PVC) plastic pipe with a cellular core and concentric inner and outer solid layers, and is produced using a multilayer coextrusion die for nonpressure use in three series: an IPS Schedule 40 series for DWV; a PS series with an iron pipe size (IPS) outside diameter with varying wall thickness as required for pipe stiffnesses of 25, 50, and 100 for communication conduit, and a sewer and drain series.  
1.2 The function of this specification is to provide standardization of product-technical data and serve as a purchasing guide.  
1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. The notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
Note 1: All the pipe series covered by this specification are permitted to be perforated or belled for joining by solvent cement or belled for joining by an elastomeric seal (gasket). Because this pipe is OD controlled, the inside diameter will vary, and therefore, the pipe ID is not suitable for use as a socket. (For more information see Specification D2672.)
Note 2: This standard specifies dimensional, performance and test requirements for plumbing and fluid handling applications, but does not address venting of combustion gases.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Note 3: Specifications related to this specification are as follows: D2665, D2729, D3034, F512, F758, and F789.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    9 pages
    English language
    sale 15% off
  • Technical specification
    9 pages
    English language
    sale 15% off
ASTM
ASTM D3034-23(Specification)
Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings

ABSTRACT
This specification covers requirements and test methods for materials, dimensions, workmanship, flattening resistance, impact resistance, pipe stiffness, extrusion quality, joining systems and a form of marking for type PSM poly(vinyl chloride) (PVC) sewer pipe and fittings. The pipe and fittings shall be homogeneous throughout and free from visible cracks, holes, foreign inclusions, or other injurious defects. The socket diameters, socket depth, wall thickness, pipe flattening, impact resistance, pipe stiffness, joint tightness, and extrusion quality shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, flattening resistance, impact resistance, pipe stiffness, extrusion quality, joining systems and a form of marking for type PSM poly(vinyl chloride) (PVC) sewer pipe and fittings.  
1.2 Pipe and fittings produced to this specification should be installed in accordance with Practice D2321.  
1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following precautionary caveat pertains only to the test methods portion, Section 8, of this specification:   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    12 pages
    English language
    sale 15% off
  • Technical specification
    12 pages
    English language
    sale 15% off
ASTM
ASTM F2818-10(2023)(Specification)
Standard Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and Tubing

ABSTRACT
This specification covers requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and impact resistance of PEX pipe and tubing for use in fuel gas mains and services for direct burial applications. Requirements cover workmanship, pipe and tubing dimensions and tolerances, chemical resistance, sustained pressure, elevated temperature, thermal stability, slow crack growth resistance, minimum hydrostatic burst pressure/apparent tensile strength (quick burst), apparent tensile strength at yield, squeeze-off, thermal stability, slow crack growth resistance, and joints.
SCOPE
1.1 This specification covers requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and impact resistance of PEX pipe and tubing for use in fuel gas mains and services for direct burial applications.  
1.2 The text of this specification references notes and footnotes provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM F628-23(Specification)
Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular Core

ABSTRACT
This specification covers coextruded acrylonitrile-butadiene-styrene (ABS) plastic drain, waste, and vent pipes made to Schedule 40 iron pipe sizes (IPS) with concentric inner and outer solid ABS layers and a closed-cell cellular ABS core. The ABS plastics used to make the pipes shall only be either virgin or reworked as specfieid. Reprocessed or recycled plastics are excluded from this specification. The pipes shall meet specified requirements for dimension such as outside diameter, wall thickness, and length; and for performance such as pipe stiffness, lower confidence limit, flattening resistance, impact strength, bond strength, pigments or screening agents, and solvent cement.
SCOPE
1.1 This specification covers coextruded acrylonitrile-butadiene-styrene (ABS) plastic drain, waste, and vent pipe made to Schedule 40 iron pipe sizes (IPS) and produced by the coextrusion process with concentric inner and outer solid ABS layers and the core consisting of closed-cell cellular ABS. Plastic which does not meet the material requirements specified in Section 5 is excluded from single layer and all coextruded layers.  
1.2 Fittings suitable for use with pipe meeting the requirements of this specification are given in Annex A1. Fittings meeting the requirement of Specification D2661 are also acceptable.  
1.3 Acrylonitrile-butadiene-styrene plastic which does not meet the definitions of virgin ABS plastic as given in 3.2.4 is excluded, as performance of plastic other than those defined as virgin was not determined. ABS rework plastic which meets the requirements of rework plastic as given in 5.3 is acceptable.  
1.4 Reprocessed plastic or recycled plastic as defined in Terminology D883 is excluded.  
1.5 Recommendations for storage, joining, and installation are provided in Appendix X1, Appendix X2, and Appendix X3, respectively.  
1.6 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.7 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    9 pages
    English language
    sale 15% off
  • Technical specification
    9 pages
    English language
    sale 15% off
ASTM
ASTM D1598-23(Test Method)
Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure

SIGNIFICANCE AND USE
5.1 The data obtained by this test method are useful for establishing stress versus failure time relationships in a controlled environment from which the hydrostatic design basis for plastic pipe materials can be computed. (Refer to Test Method D2837 and Practice D2992.)  
5.2 In order to determine how plastics will perform as pipe, it is necessary to establish the stress-failure time relationships for pipe over 2 or more logarithmic decades of time (hours) in a controlled environment. Because of the nature of the test and specimens employed, no single line can adequately represent the data, and therefore the confidence limits should be established.  
Note 2: Some materials may exhibit a nonlinear relationship between log-stress and log-failure time, usually at short failure times. In such cases, the 105-hour stress value computed on the basis of short-term test data may be significantly different than the value obtained when a distribution of data points in accordance with Test Method D2837 is evaluated. However, these data may still be useful for quality control or other applications, provided correlation with long-term data has been established.  
5.3 The factors that affect creep and long-term strength behavior of plastic pipe are not completely known at this time. This procedure takes into account those factors that are known to have important influences and provides a tool for investigating others.  
5.4 Creep, or nonrecoverable deformation for pipe made of some plastics, is as important as actual leakage in deciding whether or not a pipe has failed. Specimens that exhibit localized ballooning, however, may lead to erroneous interpretation of the creep results unless a method of determining creep is established that precludes such a possibility. Circumferential measurements at two or three selected positions on a specimen may not be adequate.  
5.5 Great care must be used to ensure that specimens are representative of the pipe under evaluation. Departure...
SCOPE
1.1 This test method covers the determination of the time-to-failure of both thermoplastic and reinforced thermosetting/resin pipe under constant internal pressure.  
1.2 This test method provides a method of characterizing plastics in the form of pipe under the conditions prescribed.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F758-14(2023)(Specification)
Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Plastic Underdrain Systems for Highway, Airport, and Similar Drainage

ABSTRACT
This specification covers the requirements for smooth-wall perforated and nonperforated poly(vinyl chloride) (PVC) plastic pipe and couplings for use in subsurface drainage systems of highways, airports, and similar applications. Two classes (or pipe stiffness) are included and designated as PS 28 and PS 46. The pipe stiffness, impact resistance, pipe flattening, and solvent cement joint tightness shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers the requirements for smooth-wall perforated and nonperforated poly(vinyl chloride) (PVC) plastic pipe and couplings for use in subsurface drainage systems of highways, airports, and similar applications in nominal sizes of 4, 6, and 8 in. and in pipe stiffnesses (PS) that are designated as Type PS 28 and Type PS 46 in accordance with its minimum pipe stiffness.  
1.2 Molded fittings for use with highway underdrain pipe are in accordance with Specification D3034. For convenience, some of these fittings are reproduced in Annex A1.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
Note 1: Type PS 28 and Type PS 46 indicate “pipe stiffness” of 28 and 46, respectively, as outlined in 11.1.
Note 2: Pipe and fittings should be installed in accordance with Practice D2321, or applicable state or local specifications.  
1.4 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following safety hazards caveat pertains only to the test methods portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM F3203-19(2023)(Test Method)
Standard Test Method for Determination of Gel Content of Crosslinked Polyethylene (PEX) Pipes and Tubing

SIGNIFICANCE AND USE
5.1 Many important properties of crosslinked ethylene plastics vary with the gel content. Hence, determination of the gel content provides a basis for controlling production processes and a means of establishing the quality of finished products.  
5.2 Extraction tests permit verification of the proper gel content of any given crosslinked ethylene plastic and they also permit comparison between different crosslinked ethylene plastics, including those containing fillers, provided that, for the latter, the following conditions are met:  
5.2.1 The filler is not soluble in the solvent used in this method at the extraction temperature.  
5.2.2 The amount of filler present in the compound either is known or can be determined.  
5.2.3 Sufficient crosslinking has been achieved to prevent migration of filler during the extraction. It has been found that, at gel content above 30 %, the solvent remains clear and free of filler.  
5.3 Since some oxidative degradation of the material and solvent may occur at the reflux temperature of the solvents, a suitable antioxidant is added to the solvent to inhibit such degradation.  
5.4 This test method is normally used for specimens consisting of an equal representation of the entire cross section of the product, but may also be used to examine specific portions of a product for differences in extent of cross-linking when compared to either a product standard or another sample.  
5.5 This test method is intended for testing crosslinked polyethylene compounds that are not hygroscopic. If compounds that are hygroscopic are tested using this method, specimen conditioning before and after extraction is required.  
5.6 This test method differs from Test Methods D2765, ISO 10147 and Test Method D7567 which also describe procedures for determining the gel content of crosslinked polyethylene. It allows for the use of naphthenic hydrocarbon blend, isoparaffin solvent, or light aromatic solvent naptha as alternatives to xylenes. Xylenes a...
SCOPE
1.1 The gel content of pipe and tubing produced from crosslinked polyethylene plastics as described in Specification F876 and other pipe or tubing standards is determined by extracting with solvents such as xylenes. A test method for quantitative determination of gel content is described herein. The method is applicable to PEX pipe and tubing of all densities, including those containing fillers, and provides correction for the inert fillers present in some of those compounds.  
1.2 Continuous extraction (see definition in Section 3) is used in this method to test the gel content of crosslinked polyethylene specimens. Continuous extraction when used for testing gel content has the advantages of decreased cost of testing, increased accuracy and consistency of results, and decreased test time. This is because extraction with a pure solvent is more efficient than extraction with a partially saturated solvent.  
1.3 While extraction tests may be made on articles of any shape, this test method is applicable for determining the gel content of crosslinked polyethylene pipes and tubing.  
1.4 This test method makes use of xylenes or alternative solvents. Alternative solvents either have lower toxicity than xylenes or allow decreased extraction times. The alternative solvents are also potentially beneficial from an economic and environmental viewpoint. Xylenes are used for referee tests.  
1.5 The values stated in SI units are to be regarded as standard. The inch-pound units in brackets are for information only.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standard...

  • Standard
    11 pages
    English language
    sale 15% off