ASTM A132-04(2009)

Standard Specification for Ferromolybdenum

ABSTRACT
This specification covers different sizes of two grades of ferromolybdenum. The material shall conform to the requirements as to composition of the following chemical elements: molybdenum, carbon, phosphorus, sulfur, silicon, and copper.
SCOPE
1.1 This specification covers two grades of ferromolybdenum.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

General Information

• Status: Historical
• Publication Date: 30-Sep-2009
• ICS: 77.100 - Ferroalloys
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.18 - Castings

Relations

• Replaces: ASTM A132-04 - Standard Specification for Ferromolybdenum
• Effective Date: 01-Oct-2009
• Replaced By: ASTM A132-04(2014) - Standard Specification for Ferromolybdenum
• Effective Date: 01-Oct-2014
• Referred By: ASTM A1025/A1025M-10(2020) - Standard Specification for Ferroalloys and Other Alloying Materials, General Requirements
• Effective Date: 01-Oct-2009

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A132 −04(Reapproved 2009)
Standard Specification for
Ferromolybdenum
This standard is issued under the fixed designation A132; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3. General Conditions for Delivery
1.1 This specification covers two grades of ferromolybde- 3.1 Materials furnished to this specification shall conform to
num. therequirementsofSpecificationA1025,includinganysupple-
mentary requirements that are indicated in the purchase order.
1.2 The values stated in inch-pound units are to be regarded
Failure to comply with the general requirements of Specifica-
as standard. The values given in parentheses are mathematical
tion A1025 constitutes nonconformance with this specification.
conversions to SI units that are provided for information only
In case of conflict between the requirements of this specifica-
and are not considered standard.
tion and Specification A1025, this specification shall prevail.
2. Referenced Documents
4. Chemical Requirements
2.1 ASTM Standards:
4.1 The material shall conform to the requirements as to
A1025 Specification for Ferroalloys and Other Alloying
chemical composition specified in Table 1. The manufacturer
Materials, General Requirements
shall furnish an analysis of each shipment showing the per-
E11 Specification for Woven Wire Test Sieve Cloth and Test
centage of each element specified.
Sieves
5. Size
5.1 The grades are available in sizes as listed in Table 2.
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
5.2 The sizes listed in Table 2 are typical as shipped from
A01.18 on Castings.
the manufacturer’s plant. These alloys exhibit varying degrees
Current edition approved Oct. 1, 2009. Published January 2010. Originally
of friability; therefore, some attrition may be expected in
approved in 1963. Last previous edition approved in 2004 as A132 – 04. DOI:
10.1520/A0132-04R09.
transit, storage, and handling.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
6. Keywords
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. 6.1 ferromolybdenum; molybdenum
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
...