ASTM C1486-00(2012)
(Practice)Standard Practice for Testing Chemical-Resistant Broadcast and Slurry-Broadcast Resin Monolithic Floor Surfacings
Standard Practice for Testing Chemical-Resistant Broadcast and Slurry-Broadcast Resin Monolithic Floor Surfacings
SIGNIFICANCE AND USE
4.1 Because the sample is prepared in a manner as it would be applied in the field, the test specimens may be considered representative of the application of a specified surfacing. Such methods include application by squeegees, rollers, trowels, notched trowels, and gage rakes.
4.2 These systems vary in several ways, including the number of layers or application steps, the surface finish, and variation in composition.
4.3 The results obtained in carrying out this practice should serve as a guide in comparing similarly applied surfacings. No attempt has been made to incorporate into this practice all of the various factors that may affect the performance of such applications when subjected to actual service.
SCOPE
1.1 This practice covers methods for preparing test specimens and testing procedures for broadcast or slurry-broadcast monolithic floor surfacings in areas where chemical resistance is required.
1.2 These floor surfacings are applied by various application methods including squeegees, rollers, trowels, notched trowels, and gage rakes onto suitably prepared concrete substrates. The surfacings bond to the substrate upon curing to provide a nominal thickness of 60 mils (1.5 mm) or greater.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1486 − 00 (Reapproved 2012)
Standard Practice for
Testing Chemical-Resistant Broadcast and Slurry-Broadcast
1
Resin Monolithic Floor Surfacings
This standard is issued under the fixed designation C1486; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope C905 Test Methods for Apparent Density of Chemical-
Resistant Mortars, Grouts, Monolithic Surfacings, and
1.1 This practice covers methods for preparing test speci-
Polymer Concretes
mens and testing procedures for broadcast or slurry-broadcast
C1028 TestMethodforDeterminingtheStaticCoefficientof
monolithic floor surfacings in areas where chemical resistance
Friction of Ceramic Tile and Other Like Surfaces by the
is required.
Horizontal Dynamometer Pull-Meter Method
1.2 Thesefloorsurfacingsareappliedbyvariousapplication
D635 Test Method for Rate of Burning and/or Extent and
methodsincludingsqueegees,rollers,trowels,notchedtrowels,
Time of Burning of Plastics in a Horizontal Position
and gage rakes onto suitably prepared concrete substrates. The
D790 Test Methods for Flexural Properties of Unreinforced
surfacings bond to the substrate upon curing to provide a
and Reinforced Plastics and Electrical Insulating Materi-
nominal thickness of 60 mils (1.5 mm) or greater.
als
D1308 Test Method for Effect of Household Chemicals on
1.3 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical Clear and Pigmented Organic Finishes
D2047 Test Method for Static Coefficient of Friction of
conversions to SI units that are provided for information only
and are not considered standard. Polish-Coated Flooring Surfaces as Measured by the
James Machine
1.4 This standard does not purport to address all of the
D4060 Test Method for Abrasion Resistance of Organic
safety concerns, if any, associated with its use. It is the
Coatings by the Taber Abraser
responsibility of the user of this standard to establish appro-
D4541 Test Method for Pull-Off Strength of Coatings Using
priate safety and health practices and determine the applica-
Portable Adhesion Testers
bility of regulatory limitations prior to use.
2.2 ACI Standards:
ACI 503R, Appendix A, Test Method A.1, Field Test for
2. Referenced Documents
4
Surface Soundness and Adhesion
2
2.1 ASTM Standards:
C413 Test Method for Absorption of Chemical-Resistant
3. Terminology
Mortars, Grouts, Monolithic Surfacings, and Polymer
3.1 Definitions—For definitions of terms relating to this
Concretes
standard, refer to Terminology C904.
C811 Practice for Surface Preparation of Concrete for Ap-
plication of Chemical-Resistant Resin Monolithic Surfac-
4. Significance and Use
3
ings (Withdrawn 2012)
4.1 Because the sample is prepared in a manner as it would
C904 Terminology Relating to Chemical-Resistant Nonme-
be applied in the field, the test specimens may be considered
tallic Materials
representative of the application of a specified surfacing. Such
methods include application by squeegees, rollers, trowels,
1 notched trowels, and gage rakes.
This practice is under the jurisdiction of ASTM Committee D01 on Paint and
Related Coatings, Materials, and Applications and is the direct responsibility of
4.2 These systems vary in several ways, including the
Subcommittee D01.46 on Industrial Protective Coatings.
number of layers or application steps, the surface finish, and
Current edition approved Aug. 1, 2012. Published September 2012. Originally
approved in 2000. Last previous edition approved in 2008 as C1486 – 00 (2008). variation in composition.
DOI: 10.1520/C1486-00R12.
2 4.3 The results obtained in carrying out this practice should
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM serve as a guide in comparing similarly applied surfacings. No
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
3 4
The last approved version of this historical standard is referenced on Available fromAmerican Concrete Institute (ACI), P.O. Box 9094, Farmington
www.astm.org. Hills, MI 48333-9094, http://www.concrete.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1486 − 00 (2012)
attempt has been made to incorporate into this practice all of average milligram of weight loss per 1000 cycles shall be
the various factors that may affect the performance of such reported. For more abrasion resistant floors a H-22 wheel m
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.