ASTM F836M-02(2015)
(Specification)Standard Specification for Style 1 Stainless Steel Metric Nuts (Metric)
Standard Specification for Style 1 Stainless Steel Metric Nuts (Metric)
ABSTRACT
This specification covers the chemical and mechanical requirements for style 1 stainless steel metric nuts. Groups and property classes of austenitic, ferritic, martensitic, and precipitation hardening stainless steel alloys are covered. Materials shall be cold-formed, hot-formed, or machined form, and shall conform to chemical, mechanical, dimensional and surface finish properties. Stainless steel shall also conform to heat treatment requirements depending on material grade. The material shall be capable of passing chemical, mechanical, and corrosion resistance tests in accordance to the specification. Product marking and packaging shall conform to the requirements of the specification.
SCOPE
1.1 This specification covers the chemical and mechanical requirements for stainless steel metric nuts with nominal thread diameters M1.6 through M36 and intended for use in engineering applications requiring general corrosion resistance.
1.2 Eight groups of stainless steel alloys are covered, including three austenitic (Grades A1, A2, and A4), one ferritic (Grade F1), three martensitic (Grades C1, C3, and C4), and one precipitation hardening (Grade P1).
1.3 Seventeen property classes are covered, including nine austenitic, one ferritic, six martensitic, and one precipitation hardening. The property classes with the permissible alloys for each are listed in Table 1. (A) When approved by the purchaser, Alloys 303, 303Se, or XM1 may be furnished.(B) When approved by the purchaser, Alloy 430F may be furnished.
1.4 This specification is based in concept and content on ISO 3506. The chemical and mechanical requirements specified for all property classes, except as given in 1.4.1, are essentially identical with classes of the same designation in ISO 3506.
1.4.1 This specification includes 13 of the 16 property classes covered in ISO 3506. Additionally, it includes property classes A1-70, A2–70, A4–70, A1–80, A2–80, and A4–80 for products with nominal thread diameters larger than M20; and four non-ISO property classes, C1-110, C4-110, C3-120, and P1-90.
1.5 Supplementary requirements of an optional nature are provided, applicable only when agreed upon between the manufacturer and the purchaser at the time of the inquiry and order.
1.6 Suitable bolts, hex cap screws, and studs for use with nuts included in this specification are covered by Specification F738M. Unless otherwise specified, all bolts, hex cap screws, and studs used with these nuts shall conform to the requirements of Specification F738M and shall be of the same alloy group.
1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F836M −02(Reapproved 2015)
Standard Specification for
1
Style 1 Stainless Steel Metric Nuts (Metric)
This standard is issued under the fixed designation F836M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope 1.7 The values stated in SI units are to be regarded as
standard. No other units of measurement are included in this
1.1 This specification covers the chemical and mechanical
standard.
requirementsforstainlesssteelmetricnutswithnominalthread
diametersM1.6throughM36andintendedforuseinengineer-
2. Referenced Documents
ing applications requiring general corrosion resistance.
2
2.1 ASTM Standards:
1.2 Eight groups of stainless steel alloys are covered,
A262Practices for Detecting Susceptibility to Intergranular
includingthreeaustenitic(GradesA1,A2,andA4),oneferritic
Attack in Austenitic Stainless Steels
(GradeF1),threemartensitic(GradesC1,C3,andC4),andone
A342/A342MTest Methods for Permeability of Weakly
precipitation hardening (Grade P1).
Magnetic Materials
1.3 Seventeen property classes are covered, including nine
A380Practice for Cleaning, Descaling, and Passivation of
austenitic, one ferritic, six martensitic, and one precipitation
Stainless Steel Parts, Equipment, and Systems
hardening.Thepropertyclasseswiththepermissiblealloysfor
A493Specification for Stainless Steel Wire and Wire Rods
each are listed in Table 1. for Cold Heading and Cold Forging
A555/A555MSpecification for General Requirements for
1.4 This specification is based in concept and content on
Stainless Steel Wire and Wire Rods
ISO 3506. The chemical and mechanical requirements speci-
A564/A564M Specification for Hot-Rolled and Cold-
fied for all property classes, except as given in 1.4.1, are
Finished Age-Hardening Stainless Steel Bars and Shapes
essentially identical with classes of the same designation in
A582/A582MSpecification for Free-Machining Stainless
ISO 3506.
Steel Bars
1.4.1 This specification includes 13 of the 16 property
A751Test Methods, Practices, and Terminology for Chemi-
classes covered in ISO 3506.Additionally, it includes property
cal Analysis of Steel Products
classes A1-70, A2–70, A4–70, A1–80, A2–80, and A4–80 for
D3951Practice for Commercial Packaging
products with nominal thread diameters larger than M20; and
E29Practice for Using Significant Digits in Test Data to
four non-ISO property classes, C1-110, C4-110, C3-120, and
Determine Conformance with Specifications
P1-90.
F606MTest Methods for Determining the Mechanical Prop-
1.5 Supplementary requirements of an optional nature are
erties of Externally and Internally Threaded Fasteners,
provided, applicable only when agreed upon between the
Washers, and Rivets (Metric)
manufacturer and the purchaser at the time of the inquiry and
F738M Specification for Stainless Steel Metric Bolts,
order. 3
Screws, and Studs (Withdrawn 2014)
1.6 Suitable bolts, hex cap screws, and studs for use with
F1470Practice for Fastener Sampling for Specified Me-
nuts included in this specification are covered by Specification chanical Properties and Performance Inspection
F738M. Unless otherwise specified, all bolts, hex cap screws,
2.2 ISO Standard:
4
and studs used with these nuts shall conform to the require-
ISO3506 Corrosion-Resistant Stainless Steel Fasteners
ments of Specification F738M and shall be of the same alloy
group.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
1
This specification is under the jurisdiction of ASTM Committee F16 on the ASTM website.
3
Fastenersand is the direct responsibility of Subcommittee F16.04 on Nonferrous The last approved version of this historical standard is referenced on
Fasteners. www.astm.org.
4
Current edition approved Sept. 1, 2015. Published November 2015. Originally Available from American Society of Mechanical Engineers (ASME), ASME
approvedin1983.Lastpreviouseditionapprovedin2010asF536–02(2010).DOI: International Headquarters, Three Park Ave., New York, NY 10016-5990, http://
10.1520/F0836M-02R15. www.asme.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F836M−02 (2015)
TABLE 1 Property Classes of Stainless Steel Nuts
4.1.1 Quantity (number of pieces of each item);
Property Class Permissible Alloys
4.1.2 Name of item (specific type and s
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F836M − 02 (Reapproved 2010) F836M − 02 (Reapproved 2015)
Standard Specification for
1
Style 1 Stainless Steel Metric Nuts (Metric)
This standard is issued under the fixed designation F836M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1.1 This specification covers the chemical and mechanical requirements for stainless steel metric nuts with nominal thread
diameters M1.6 through M36 and intended for use in engineering applications requiring general corrosion resistance.
1.2 Eight groups of stainless steel alloys are covered, including three austenitic (Grades A1, A2, and A4), one ferritic (Grade
F1), three martensitic (Grades C1, C3, and C4), and one precipitation hardening (Grade P1).
1.3 Seventeen property classes are covered, including nine austenitic, one ferritic, six martensitic, and one precipitation
hardening. The property classes with the permissible alloys for each are listed in Table 1.
1.4 This specification is based in concept and content on ISO 3506. The chemical and mechanical requirements specified for
all property classes, except as given in 1.4.1, are essentially identical with classes of the same designation in ISO 3506.
1.4.1 This specification includes 13 of the 16 property classes covered in ISO 3506. Additionally, it includes property classes
A1-70, A2–70, A4–70, A1–80, A2–80, and A4–80 for products with nominal thread diameters larger than M20; and four non-ISO
property classes, C1-110, C4-110, C3-120, and P1-90.
1.5 Supplementary requirements of an optional nature are provided, applicable only when agreed upon between the
manufacturer and the purchaser at the time of the inquiry and order.
1.6 Suitable bolts, hex cap screws, and studs for use with nuts included in this specification are covered by Specification F738M.
Unless otherwise specified, all bolts, hex cap screws, and studs used with these nuts shall conform to the requirements of
Specification F738M and shall be of the same alloy group.
1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
2. Referenced Documents
2
2.1 ASTM Standards:
A262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
A342/A342M Test Methods for Permeability of Weakly Magnetic Materials
A380 Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems
A493 Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging
A555/A555M Specification for General Requirements for Stainless Steel Wire and Wire Rods
A564/A564M Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and Shapes
A582/A582M Specification for Free-Machining Stainless Steel Bars
A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
D3951 Practice for Commercial Packaging
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
F606M Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and
Rivets (Metric)
3
F738M Specification for Stainless Steel Metric Bolts, Screws, and Studs (Withdrawn 2014)
F1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
1
This specification is under the jurisdiction of ASTM Committee F16 on Fastenersand is the direct responsibility of Subcommittee F16.04 on Nonferrous Fasteners.
Current edition approved Oct. 1, 2010Sept. 1, 2015. Published January 2011November 2015. Originally approved in 1983. Last previous edition approved in 20022010
as F536 – 02.F536 – 02(2010). DOI: 10.1520/F0836M-02R10.10.1520/F0836M-02R15.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ------------------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.