ASTM A391/A391M-07(2012)

Standard Specification for Grade 80 Alloy Steel Chain

ABSTRACT
This specification deals with Grade 80 heat-treated alloy steel chain for applications such as slings, lifting assemblies, and load binding. The alloy steel chain shall be made to a fully-killed fine austenitic grain process. Alloy steel chain may be made by the electric welding or gas welding process. The material shall be heat treated which includes quenching and tempering. Material's composition shall conform to the chemical requirements for carbon, phosphorous, sulfur, nickel, chromium, and molybdenum. The material shall conform to the mechanical property requirements for breaking force and elongation and to the dimensional requirements for the appropriate size chain. All chain shall be tested to at least the proof load.
SCOPE
1.1 This specification covers Grade 80 heat-treated alloy steel chain for such applications as slings, lifting assemblies, and load binding. Note 1—This specification does not cover alloy steel chain for pocket wheel applications.  
1.2 The Grade designation is 1/10 of the minimum breaking strength in newtons divided by two times the nominal cross-sectional area of the chain in square millimetres.  
1.3 The values stated in either SI units or in other units shall be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any way.

General Information

• Status: Historical
• Publication Date: 31-Oct-2012
• ICS: 77.140.65 - Steel wire, wire ropes and link chains
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.27 - Steel Chain

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A391/A391M −07 (Reapproved 2012)
Standard Specification for
1
Grade 80 Alloy Steel Chain
This standard is issued under the fixed designationA391/A391M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 3.1.2 date code, n—series of letters, numbers, or both,
embossedonthechainwhichenablesitsmanufacturinghistory
1.1 This specification covers Grade 80 heat-treated alloy
to be traced.
steel chain for such applications as slings, lifting assemblies,
and load binding. 3.1.3 lot,n—forthepurposeofacceptancetesting,alotshall
consist of 3000 ft [1000 m], or fraction thereof, of the same
NOTE 1—This specification does not cover alloy steel chain for pocket
grade and size chain. If a continuous length of chain exceeds
wheel applications.
3000 ft [1000 m], it shall also be considered a lot.
1
1.2 The Grade designation is ⁄10 of the minimum breaking
3.1.4 proof test, n—quality control tensile test applied to
strength in newtons divided by two times the nominal cross-
chain for the purpose of verifying weld and material quality.
sectional area of the chain in square millimetres.
3.1.4.1 Discussion—It is the minimum force in pounds or
1.3 ThevaluesstatedineitherSIunitsorinotherunitsshall
newtons which the chain has withstood at the time it left the
be regarded separately as standard. The values stated in each
producer, under a test in which a constantly increasing force
system may not be exact equivalents; therefore, each system
has been applied in direct tension to a straight length of chain.
must be used independently of the other, without combining
Proof test loads are a manufacturing integrity test and shall not
values in any way.
be used as criteria for service or design purposes.
3.1.5 traceability code, n—series of letters, numbers, or
2. Referenced Documents
both, embossed on the chain which enables its manufacturing
2
2.1 ASTM Standards:
history, including the identity of the steel heat, to be traced.
A29/A29MSpecification for Steel Bars, Carbon and Alloy,
3.1.6 working load limit (WLL), n—maximum combined
Hot-Wrought, General Requirements for
static and dynamic load in pounds or kilograms that shall be
A751Test Methods, Practices, and Terminology for Chemi-
applied in direct tension to an undamaged straight length of
cal Analysis of Steel Products
chain.
A941TerminologyRelatingtoSteel,StainlessSteel,Related
Alloys, and Ferroalloys
4. Ordering Information
4.1 It shall be the responsibility of the purchaser to specify
3. Terminology
all requirements that are necessary for material ordered under
3.1 Definitions of Terms Specific to This Standard:
this specification. Such requirements to be considered include,
3.1.1 breaking force, minimum, n—minimum force in
but are not limited to, the following:
poundsornewtonsatwhichthechain,duringmanufacture,has
4.1.1 Product to conform to Specification A391 or A391M
been found by testing to break when a constantly increasing
and year of issue,
force is applied in direct tension.
4.1.2 Nominal size of chain in in. [mm],
3.1.1.1 Discussion—This test is a manufacturer’s attribute
4.1.3 Quantity of chain in ft [m],
acceptance test and shall not be used as criteria for service.
4.1.4 Length of each piece, if required,
4.1.5 Finish, if required,
4.1.6 Certification of test(s), if required, and
1
This specification is under the jurisdiction ofASTM Committee A01 on Steel,
4.1.7 Acceptance of inspection by purchaser, if required.
Stainless Steel and RelatedAlloys and is the direct responsibility of Subcommittee
A01.27 on Steel Chain.
Current edition approved Nov. 1, 2012. Published November 2012. Originally 5. Manufacturing
approved in 1955. Last previous edition approved in 2007 as A391/A391M–07.
5.1 Melting Process—The alloy steel shall be made to a
DOI: 10.1520/A0391_A0391M-07R12.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or fully-killed fine austenitic grain process.
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
5.2 Welding Process—Alloysteelchainmaybemadebythe
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. electric welding or gas welding process.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
A391/A391M−07 (2012)
TABLE 2 Mechanical Test Sample Length Requirements
5.3 Heat Treatment—After welding, alloy steel chain shall
be heat treated before applying the proof test. He
...