ASTM F2088-12a
(Specification)Standard Consumer Safety Specification for Infant Swings
Standard Consumer Safety Specification for Infant Swings
SCOPE
1.1 This consumer safety specification establishes safety performance requirements, test methods, and labeling requirements to minimize the hazards to infants presented by swings as identified in the introduction.
1.2 This consumer safety specification is intended to minimize the risk of injuries to infants resulting from normal use and reasonably foreseeable misuse or abuse of infant swings. It is not intended to address all incidents and injuries resulting from the interaction of other persons with the infant in the swing.
1.3 No swing produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this consumer safety specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F2088 −12a
StandardConsumer Safety Specification for
1
Infant Swings
This standard is issued under the fixed designation F2088; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
ThisconsumersafetyspecificationaddressesinfantswingincidentsidentifiedbytheU.S.Consumer
Product Safety Commission (CPSC).
In response to incident data compiled by the CPSC, this consumer safety specification attempts to
minimize the following: (1) swings tipping over or collapsing, (2) structural failures, and (3)
entanglement in the restraints or entrapment in leg holes. This consumer safety specification is
intended to cover normal use and reasonably foreseeable misuse or abuse of infant swings. This
specification does not cover swings that are blatantly misused or used in a careless manner that
disregards the safety instructions and warnings provided with each infant swing.
This consumer safety specification is written within the current state-of-the-art of infant swing
technology and will be updated whenever substantive information becomes available that necessitates
additional requirements or justifies the revision of existing requirements.
1. Scope safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
1.1 This consumer safety specification establishes safety
priate safety and health practices and determine the applica-
performance requirements, test methods, and labeling require-
bility of regulatory limitations prior to use.
ments to minimize the hazards to infants presented by swings
as identified in the introduction.
2. Referenced Documents
1.2 This consumer safety specification is intended to mini- 2
2.1 ASTM Standards:
mize the risk of injuries to infants resulting from normal use
D3359 Test Methods for Measuring Adhesion by Tape Test
and reasonably foreseeable misuse or abuse of infant swings. It
F963 Consumer Safety Specification for Toy Safety
is not intended to address all incidents and injuries resulting 3
2.2 Federal Standards:
from the interaction of other persons with the infant in the
16CFRPart1303 BanofLead-ContainingPaintandCertain
swing.
Consumer Products Bearing Lead-Containing Paint
1.3 No swing produced after the approval date of this
16 CFR Part 1500 Hazardous Substances Act Regulations
consumer safety specification shall, either by label or other including sections:
means, indicate compliance with this specification unless it 1500.48—Technical Requirements for Determining a Sharp
conforms to all requirements contained herein. Point in Toys or Other Articles Intended for Use by
Children Under Eight Years of Age
1.4 The values stated in inch-pound units are to be regarded
1500.49—Technical Requirements for Determining a Sharp
as standard. The values given in parentheses are mathematical
MetalorGlassEdgeinToysorOtherArticlesIntendedfor
conversions to SI units that are provided for information only
Use by Children Under Eight Years of Age
and are not considered standard.
1500.50-.51—Test Method for Simulating Use and Abuse
1.5 The following precautionary caveat pertains only to the
of Toys and Other Articles Intended for Use by Children
test method portion, Section 7, of this consumer safety speci-
16 CFR Part 1501 Method for Identifying Toys and Other
fication: This standard does not purport to address all of the
Articles Intended for Use by Children Under Three Years
1 2
This consumer safety specification is under the jurisdiction ofASTM Commit- For referenced ASTM standards, visit the ASTM website, www.astm.org, or
tee F15 on Consumer Products and is the direct responsibility of Subcommittee contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
F15.21 on Infant Carriers, Bouncers and Baby Swings. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Sept. 1, 2012. Published September 2012. Originally the ASTM website.
3
approved in 2001. Last previous edition approved in 2012 as F2088 – 12. DOI: AvailablefromU.S.GovernmentPrintingOfficeSuperintendentofDocuments,
10.1520/F2088-12A. 732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2088−12a
FIG. 2CAMI Newborn Dummy
3.1.5 manufacturer’s recommended use position, n—any
FIG. 1CAMI Infant Dummy, Mark II
position, that is presented as a normal, allowable, or acceptable
configuration for the use of the product by the manufact
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:F2088–12 Designation: F2088 – 12a
Standard Consumer Safety Specification for
1
Infant Swings
This standard is issued under the fixed designation F2088; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
ThisconsumersafetyspecificationaddressesinfantswingincidentsidentifiedbytheU.S.Consumer
Product Safety Commission (CPSC).
In response to incident data compiled by the CPSC, this consumer safety specification attempts to
minimize the following: (1) swings tipping over or collapsing, (2) structural failures, and (3)
entanglement in the restraints or entrapment in leg holes. This consumer safety specification is
intended to cover normal use and reasonably foreseeable misuse or abuse of infant swings. This
specification does not cover swings that are blatantly misused or used in a careless manner that
disregards the safety instructions and warnings provided with each infant swing.
This consumer safety specification is written within the current state-of-the-art of infant swing
technology and will be updated whenever substantive information becomes available that necessitates
additional requirements or justifies the revision of existing requirements.
1. Scope
1.1 This consumer safety specification establishes safety performance requirements, test methods, and labeling requirements to
minimize the hazards to infants presented by swings as identified in the introduction.
1.2 This consumer safety specification is intended to minimize the risk of injuries to infants resulting from normal use and
reasonably foreseeable misuse or abuse of infant swings. It is not intended to address all incidents and injuries resulting from the
interaction of other persons with the infant in the swing.
1.3 No swing produced after the approval date of this consumer safety specification shall, either by label or other means,
indicate compliance with this specification unless it conforms to all requirements contained herein.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 Thefollowingprecautionarycaveatpertainsonlytothetestmethodportion,Section7,ofthisconsumersafetyspecification:
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the
user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations
prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D3359 Test Methods for Measuring Adhesion by Tape Test
F963 Consumer Safety Specification for Toy Safety
3
2.2 Federal Standards:
16 CFR Part 1303 Ban of Lead-Containing Paint and Certain Consumer Products Bearing Lead-Containing Paint
16 CFR Part 1500 Hazardous Substances Act Regulations including sections:
1500.48—TechnicalRequirementsforDeterminingaSharpPointinToysorOtherArticlesIntendedforUsebyChildrenUnder
Eight Years of Age
1
This consumer safety specification is under the jurisdiction of ASTM Committee F15 on Consumer Products and is the direct responsibility of Subcommittee F15.21
on Infant Carriers, Bouncers and Baby Swings.
Current edition approved Feb.Sept. 1, 2012. Published FebruarySeptember 2012. Originally approved in 2001. Last previous edition approved in 20112012 as
F2088–11b.F2088 – 12. DOI: 10.1520/F2088-12A.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from U.S. Government Printing Office Superintendent of Documents, 732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F2088 – 12a
1500.49—Technical Requirements for Determining a Sharp Metal or Glass Edge in Toys or Other Articles Intended for Use
by Children Under Eight Years of Age
1500.50-.51—Test Method for Simulating Use and Abuse of Toys and Other Articles Intended for Use by Children
16 CFR Part 1501 Method for Identif
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.