iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D1516-05(2010)

(Test Method)

Standard Test Method for Width of Leather

Standard Test Method for Width of Leather

SIGNIFICANCE AND USE
This test method is designed to measure the width of specimens before and after they are subjected to various tests which may change the width. A test procedure wherein such measurements could be used is the change in area of square pieces when measuring the resistance of leather to synthetic perspiration solution.
SCOPE
1.1 This test method covers determination of the width of physical test specimens and of regularly shaped units and pieces of all types of leather. This test method does not apply to wet blue.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
30-Sep-2010
ICS
59.140.30 - Leather and furs
Technical Committee
D31 - Leather
Drafting Committee
D31.07 - Physical Properties
Current Stage
Ref Project

Relations

Replaces
ASTM D1516-05 - Standard Test Method for Width of Leather
Effective Date
01-Oct-2010
Referred By
ASTM D1815-00(2021) - Standard Test Method for Water Absorption (Static) of Vegetable Tanned Leather
Effective Date
01-Oct-2010

Buy Standard

ASTM D1516-05(2010) - Standard Test Method for Width of LeatherASTM D1516-05(2010) - Standard Test Method for Width of Leather
PreviousNext
Standard
ASTM D1516-05(2010) - Standard Test Method for Width of Leather
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D1516 − 05 (Reapproved 2010)
Standard Test Method for
1
Width of Leather
This standard is issued under the fixed designation D1516; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope 5. Specimen
1.1 This test method covers determination of the width of 5.1 The specimen shall be the prepared test specimen, unit,
physical test specimens and of regularly shaped units and or piece. It shall be conditioned for 48 h in an atmosphere
pieces of all types of leather. This test method does not apply maintained at 73.4 6 1.8°F (23 6 1°C) and 50 6 4 % relative
to wet blue. humidity and tested under these conditions. See Practice
D1610.
1.2 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical
6. Procedure
conversions to SI units that are provided for information only
6.1 Test Specimens—Place the specimen on a flat surface
and are not considered standard.
and flatten it out without pulling or stretching. Measure the
1.3 This standard does not purport to address all of the
width to the nearest 0.02 in. (0.5 mm) at the locations
safety concerns, if any, associated with its use. It is the
designated in the test method for making the particular test for
responsibility of the user of this standard to establish appro-
which the specimen was prepared.
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use.
7. Calculation and Report
7.1 Report the width of the test specimens used as pre-
2. Referenced Documents
scribed in the test method for making the particular physical
2
2.1 ASTM Standards:
test for which the specimen was prepared.
D1610 Practice for Conditioning Leather and Leather Prod-
7.2 Report the average of the width measurements taken on
ucts for Testing
any unit or piece to the same accuracy as observed on the
3. Significance and Use
original measurements, as the width of the piece.
3.1 This test method is designed to measure the width of
3
8. Precision and Bias
specimens before and after they are subjected to various tests
8.1 The following criteria may be used to judge the accept-
which may change the width. A test procedure wherein such
ability of results if at least 15 units have been tested.
measurements could be used is the change in area of square
pieces when measuring the resistance of leather to synthetic
8.2 A coefficient of variation of 1.8 % can be expected
perspiration solution.
between laboratories on specimens of headband leather sub-
jected to a perspiration test.
4. Appara
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D3495-10(2023)(Test Method)
Standard Test Method for Hexane Extraction of Leather

SIGNIFICANCE AND USE
3.1 This test method measures the amount of hexane-soluble lubricant present in all types of leather. Adequate lubrication prevents abrasion of leather fibers during flexing. This lubrication is generally obtained from the fat liquor added at the tannery. Some lubrication is also obtained from natural grease produced during the life of the animal.
SCOPE
1.1 This test method covers the quantitative extraction of all types of leather with hexane. This test method does not apply to wet blue.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6016-17(2023)(Test Method)
Standard Test Method for Determination of Nitrogen, Water Extractable in Leather

SIGNIFICANCE AND USE
3.1 This test method provides the means to determine nitrogen containing water extractable materials such as excess and loosely bound tannins, ammonium salts, and nitrates.
SCOPE
1.1 This test method covers quantitatively determining the water extractable nitrogen in leather.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D4655-95(2023)(Test Method)
Standard Test Methods for Sulfates in Leather (Total, Neutral, and Combined Acid)

SIGNIFICANCE AND USE
3.1 These test methods are used to determine the basicity of leather when used in accordance with Test Method D4654.
SCOPE
1.1 These test methods are intended for use in determining the total, neutral, and combined acid sulfate in mineral-tanned leather.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D8042-18(2023)(Test Method)
Test Method for Shrinkage Temperature of Wet Blue and Wet White

SIGNIFICANCE AND USE
5.1 This test method is designed to determine the temperature at which the Wet Blue or Wet White specimen experiences shrinkage. In this test method, shrinkage occurs as a result of hydrothermal denaturation of the collagen protein molecules which make up the fiber structure of the Wet Blue or Wet White. The shrinkage temperature of Wet Blue or Wet White is influenced by many different factors, most of which appear to affect the number and nature of crosslinking interactions between adjacent polypeptide chains of the collagen protein molecules. The value of the shrinkage temperature of Wet Blue or Wet White is commonly used as an indicator of the type of tannage or the degree of tannage, or both, of that particular Wet Blue or Wet White (especially for the more hydrothermally stable tannages such as chrome tannage).
SCOPE
1.1 This test method covers the determination of the shrinkage temperature of all types of Wet Blue and Wet White. The heating medium is water when the shrinkage temperature is at or below 98 °C. The heating medium is a glycerine-water solution when the shrinkage temperature is above 98 °C.  
1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D1913-00(2023)(Test Method)
Standard Test Method for Resistance to Wetting of Garment-Type Leathers (Spray Test)

SIGNIFICANCE AND USE
3.1 The procedure is intended primarily to evaluate garment-type leathers. The test method is qualitative and measures the surface-water repellency or surface-water resistance only. It is not intended for use in determining resistance to water penetration. A visual means is given to evaluate the relative effects of materials showing water repellency, but no comparison is possible with conditions found in actual use.
SCOPE
1.1 This test method covers the qualitative evaluation of the surface repellency to water of garment-type leathers. This test method does not apply to wet blue.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values shown in parentheses are provided for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6014-00(2023)(Test Method)
Standard Test Method for Determination of Dynamic Water Absorption of Leather Surfaces

SIGNIFICANCE AND USE
3.1 This test method may be used to measure the effectiveness of water resistant treatments of light leathers such as glove and garment leather that have no finish. It can also be used to measure the water absorption capacity of insole materials thus providing a gauge for predicting foot comfort or discomfort.
SCOPE
1.1 This test method covers determining the degree of wettability of a leather surface. This test method does not apply to wet blue.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D5053-03(2023)(Test Method)
Standard Test Method for Colorfastness of Crocking of Leather

SIGNIFICANCE AND USE
5.1 This test method is intended for use on any type of leather.
SCOPE
1.1 This test method covers the determination of the degree of color that may be transferred from leather to other surfaces by rubbing under wet (damp) or dry conditions, or both. This test method does not apply to wet blue.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D5552-10(2023)(Test Method)
Standard Test Method for Resistance of Colored Leather to Bleeding

SIGNIFICANCE AND USE
4.1 Bleed resistance is considered to be an important characteristic in leather used to make lined and unlined items that may come in contact with water.
SCOPE
1.1 This test method covers the determination of the resistance of colored leather to bleeding. This test method does not apply to wet blue.  
1.2 This test method is intended for use on finished upper leather for shoes or similar end use, or the leather article such as shoe, handbag, etc.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D1813-13(2023)(Test Method)
Standard Test Method for Measuring Thickness of Leather Test Specimens

SIGNIFICANCE AND USE
3.1 This test method shall be used where precise dimensions are necessary for calculation of properties expressed in physical units. It is not intended to replace practical thickness measurements based on commercial portable tools, nor is it implied that thickness measurements made by the two procedures will agree exactly.
SCOPE
1.1 This test method covers the measurement of the thickness of leather test specimens in which the dimensions of the specimens are used directly in determining the results of tests for physical properties. This test method does not apply to wet blue.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6077-16(2023)(Test Method)
Standard Test Method for Trapezoid Tearing Strength of Leather

SIGNIFICANCE AND USE
4.1 The trapezoid tearing load is a tension test in which the test strength is determined primarily by the interlocking structure of the fibers. It is useful for estimating relative ease of tearing of leather.  
4.2 The procedure can also be used to determine if there is any appreciable difference in the relative strength of the leather in the parallel and the perpendicular directions to the backbone.
SCOPE
1.1 This test method covers the measurement of the tearing load of nonwoven fabrics by the trapezoid method for leather. This test method does not apply to wet blue.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off