ASTM C203-05a(2017)

Standard Test Methods for Breaking Load and Flexural Properties of Block-Type Thermal Insulation

SIGNIFICANCE AND USE
5.1 These test methods are to be used to determine the resistance of some types of preformed block insulation when transverse loads are normally applied to the surface. Values are measured at the maximum load or breaking point under specified conditions or specimen size, span between supports, and rate of load application. The equations used are based on the assumption that the materials are uniform and presume that the stress-strain characteristics below the elastic limit are linearly elastic. These assumptions are not strictly applicable to thermal insulations of certain types in which crushing occurs before failure is obtained in transverse bending; however, depending upon the accuracy required, these procedures are capable of providing acceptable results.  
5.2 Test Method I is especially useful when testing only for the modulus of rupture or the breaking load. This information is useful for quality control inspection and qualification for specification purposes.  
5.3 Test Method II is useful in determining the elastic modulus in bending as well as the flexural strength. Flexural properties determined by these test methods are also useful for quality control and specification purposes.  
5.4 The basic differences between the two test methods is in the location of the maximum bending moment, maximum axial fiber (flexural or tensile) stresses, and the resolved stress state in terms of shear stress and tensile/compression stress. The maximum axial fiber stresses occur on a line under the loading fitting in Test Method I and over the area between the loading fittings in Test Method II. Test Method I has a high shear stress component in the direction of loading, perpendicular to the axial fiber stress. Sufficient resolved shear stress is capable of producing failure by a shear mode rather than a simple tension/flexural failure. There is no comparable shear component in the central region between the loading fittings in Test Method II. Test Method II simulates a u...
SCOPE
1.1 These test methods cover the determination of the breaking load and calculated flexural strength of a rectangular cross section of a preformed block-type thermal insulation tested as a simple beam. It is also applicable to cellular plastics. Two test methods are described as follows:  
1.1.1 Test Method I—A loading system utilizing center loading on a simply supported beam, supported at both ends.  
1.1.2 Test Method II—A loading system utilizing two symmetric load points equally spaced from their adjacent support points at each end with a distance between load points of one half of the support span.  
1.2 Either test method is capable of being used with the four procedures that follow:  
1.2.1 Procedure A—Designed principally for materials that break at comparatively small deflections.  
1.2.2 Procedure B—Designed particularly for those materials that undergo large deflections during testing.  
1.2.3 Procedure C—Designed for measuring at a constant stress rate, using a CRL (constant rate of loading) machine. Used for breaking load measurements only.  
1.2.4 Procedure D—Designed for measurements at a constant crosshead speed, using either a CRT (constant rate of traverse) or CRE (constant rate of extension) machine. Used for breaking load measurements using a fixed crosshead speed machine.  
1.3 Comparative tests are capable of being run according to either method or procedure, provided that the method or procedure is found satisfactory for the material being tested.  
1.4 These test methods are purposely general in order to accommodate the widely varying industry practices. It is important that the user consult the appropriate materials specification for any specific detailed requirements regarding these test methods.  
1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information only.  
1.6 This standard does not purport to address all...

General Information

• Status: Historical
• Publication Date: 31-Aug-2017
• ICS: 91.100.60 - Thermal and sound insulating materials
• Technical Committee: C16 - Thermal Insulation
• Drafting Committee: C16.32 - Mechanical Properties

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C203 − 05a (Reapproved 2017)
Standard Test Methods for
Breaking Load and Flexural Properties of Block-Type
1
Thermal Insulation
This standard is issued under the fixed designation C203; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope 1.5 The values stated in SI units are to be regarded as the
standard. The values given in parentheses are provided for
1.1 These test methods cover the determination of the
information only.
breaking load and calculated flexural strength of a rectangular
1.6 This standard does not purport to address all of the
cross section of a preformed block-type thermal insulation
safety concerns, if any, associated with its use. It is the
testedasasimplebeam.Itisalsoapplicabletocellularplastics.
responsibility of the user of this standard to establish appro-
Two test methods are described as follows:
priate safety, health, and environmental practices and deter-
1.1.1 Test Method I—A loading system utilizing center
mine the applicability of regulatory limitations prior to use.
loading on a simply supported beam, supported at both ends.
For specific precautionary statements, see Section 11
1.1.2 Test Method II—A loading system utilizing two sym-
1.7 This international standard was developed in accor-
metric load points equally spaced from their adjacent support
dance with internationally recognized principles on standard-
points at each end with a distance between load points of one
ization established in the Decision on Principles for the
half of the support span.
Development of International Standards, Guides and Recom-
1.2 Either test method is capable of being used with the four
mendations issued by the World Trade Organization Technical
procedures that follow:
Barriers to Trade (TBT) Committee.
1.2.1 Procedure A—Designed principally for materials that
break at comparatively small deflections.
2. Referenced Documents
1.2.2 Procedure B—Designed particularly for those materi-
2
2.1 ASTM Standards:
als that undergo large deflections during testing.
C133 Test Methods for Cold Crushing Strength and Modu-
1.2.3 Procedure C—Designed for measuring at a constant
lus of Rupture of Refractories
stress rate, using a CRL (constant rate of loading) machine.
C168 Terminology Relating to Thermal Insulation
Used for breaking load measurements only.
C390 Practice for Sampling and Acceptance of Thermal
1.2.4 Procedure D—Designed for measurements at a con-
Insulation Lots
stant crosshead speed, using either a CRT (constant rate of
C870 Practice for Conditioning of Thermal Insulating Ma-
traverse) or CRE (constant rate of extension) machine. Used
terials
for breaking load measurements using a fixed crosshead speed
D76 Specification for Tensile Testing Machines for Textiles
machine.
E4 Practices for Force Verification of Testing Machines
1.3 Comparative tests are capable of being run according to
either method or procedure, provided that the method or
3. Terminology
procedure is found satisfactory for the material being tested.
3.1 Terminology C168 shall be considered applied to the
1.4 These test methods are purposely general in order to
terms used in this method.
accommodate the widely varying industry practices. It is
important that the user consult the appropriate materials
4. Summary of Test Methods
specification for any specific detailed requirements regarding
4.1 A bar of rectangular cross section is tested in flexure as
these test methods.
a beam as follows:
1
These test methods are under the jurisdiction of ASTM Committee C16 on
Thermal Insulation and are the direct responsibility of Subcommittee C16.32 on
2
Mechanical Properties. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Sept. 1, 2017. Published December 2017. Originally contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
approved in 1945. Last previous edition approved 2012 as C203 – 05a (2012). DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/C0203-05AR17. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C203 − 05a (2017)
4.1.1 Test Method I—The bar rests on two supports and is
loaded by means of a loading fitting or piece midway between
the supports (see Fig. 1).
4.1.2 Test Method II—The bar rests on two supports and is
loaded at the two quarter points (by means of two loading
fitt
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C203 − 05a (Reapproved 2012) C203 − 05a (Reapproved 2017)
Standard Test Methods for
Breaking Load and Flexural Properties of Block-Type
1
Thermal Insulation
This standard is issued under the fixed designation C203; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1.1 These test methods cover the determination of the breaking load and calculated flexural strength of a rectangular cross
section of a preformed block-type thermal insulation tested as a simple beam. It is also applicable to cellular plastics. Two test
methods are described as follows:
1.1.1 Test Method I—A loading system utilizing center loading on a simply supported beam, supported at both ends.
1.1.2 Test Method II—A loading system utilizing two symmetric load points equally spaced from their adjacent support points
at each end with a distance between load points of one half of the support span.
1.2 Either test method is capable of being used with the four procedures that follow:
1.2.1 Procedure A—Designed principally for materials that break at comparatively small deflections.
1.2.2 Procedure B—Designed particularly for those materials that undergo large deflections during testing.
1.2.3 Procedure C—Designed for measuring at a constant stress rate, using a CRL (constant rate of loading) machine. Used for
breaking load measurements only.
1.2.4 Procedure D—Designed for measurements at a constant crosshead speed, using either a CRT (constant rate of traverse)
or CRE (constant rate of extension) machine. Used for breaking load measurements using a fixed crosshead speed machine.
1.3 Comparative tests are capable of being run according to either method or procedure, provided that the method or procedure
is found satisfactory for the material being tested.
1.4 These test methods are purposely general in order to accommodate the widely varying industry practices. It is important that
the user consult the appropriate materials specification for any specific detailed requirements regarding these test methods.
1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information
only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 11
1.7 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
C133 Test Methods for Cold Crushing Strength and Modulus of Rupture of Refractories
C168 Terminology Relating to Thermal Insulation
C390 Practice for Sampling and Acceptance of Thermal Insulation Lots
C870 Practice for Conditioning of Thermal Insulating Materials
D76 Specification for Tensile Testing Machines for Textiles
1
These test methods are under the jurisdiction of ASTM Committee C16 on Thermal Insulation and are the direct responsibility of Subcommittee C16.32 on Mechanical
Properties.
Current edition approved March 1, 2012Sept. 1, 2017. Published May 2012December 2017. Originally approved in 1945. Last previous edition approved 20052012 as
C203 – 05a.C203 – 05a (2012). DOI: 10.1520/C0203-05AR12.10.1520/C0203-05AR17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C203 − 05a (2017)
E4 Practices for Force Verification of Testing Machines
3. Terminology
3.1 Terminology C168 shall be considered applied to the terms used in this method.
4.
...