ASTM D3757-16
(Guide)Standard Guide for Preparing Specifications for Solvent-based Floor Polishes
Standard Guide for Preparing Specifications for Solvent-based Floor Polishes
SIGNIFICANCE AND USE
3.1 This guide may be the basis for either the buying authority or the consumer to prepare a specification for solvent-based floor polishes (liquid or paste). Specifications prepared under this guide are for products intended for use on all wood and solvent resistant floors. Any reference material utilized and limits set are to be agreed upon by the seller, purchaser, or user.
SCOPE
1.1 This is a guide for preparing specifications for solvent-based floor polishes (liquid or paste) that are intended for use on all wood and solvent-resistant floors.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D3757 −16
Standard Guide for
1
Preparing Specifications for Solvent-based Floor Polishes
This standard is issued under the fixed designation D3757; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
3
1. Scope 2.2 Federal Specification:
Interim Federal Specification, Wax, General Purpose, Sol-
1.1 This is a guide for preparing specifications for solvent-
vent Type, P-W-00158d (GSA-FSS) Amendment 1, July
based floor polishes (liquid or paste) that are intended for use
13, 1972.
on all wood and solvent-resistant floors.
1.2 The values stated in SI units are to be regarded as
3. Significance and Use
standard. No other units of measurement are included in this
3.1 This guide may be the basis for either the buying
standard.
authority or the consumer to prepare a specification for
1.3 This standard does not purport to address all of the
solvent-based floor polishes (liquid or paste). Specifications
safety concerns, if any, associated with its use. It is the
prepared under this guide are for products intended for use on
responsibility of the user of this standard to establish appro-
all wood and solvent resistant floors. Any reference material
priate safety and health practices and determine the applica-
utilized and limits set are to be agreed upon by the seller,
bility of regulatory limitations prior to use.
purchaser, or user.
2. Referenced Documents
4. Classification
2
2.1 ASTM Standards:
4.1 Buffıng-Type Floor Polish—A floor polish that requires
D56 Test Method for Flash Point by Tag Closed Cup Tester
buffing to maintain or enhance appearance, or both.
D93 Test Methods for Flash Point by Pensky-Martens
4.2 Self-Polishing Floor Polish—Afloor polish that dries to
Closed Cup Tester
a shine.
D217 Test Methods for Cone Penetration of Lubricating
Grease
5. Basis of Purchase
D1455 Test Method for 60° Specular Gloss of Emulsion
5.1 Identification of Samples—The qualification sample
Floor Polish
submitted by the manufacturer will be identified for the
D2047 Test Method for Static Coefficient of Friction of
purposeofcomparingwithmaterialsubsequentlysubmittedfor
Polish-Coated Flooring Surfaces as Measured by the
acceptance. Within test method limits, stated herein, qualifica-
James Machine
tionandacceptancesamplesshouldbeidentical.Anylotorlots
D2834 Test Method for Nonvolatile Matter (Total Solids) in
found not to be identical with the standard sample shall be
Water-Emulsion Floor Polishes, Solvent-Based Floor
rejected. Reference material is to be agreed upon between the
Polishes, and Polymer-Emulsion Floor Polishes
purchaser and the seller.
D3206 Test Method for Soil Resistance of Floor Polishes
D3207 TestMethod for Detergent Resistance of FloorPolish
6. Requirements
Films
D3278 Test Methods for Flash Point of Liquids by Small 6.1 Physical (Product Specification Values or Limits):
Scale Closed-Cup Apparatus 6.1.1 Total Solids—The solids shall not be greater than ( )
D3828 Test Methods for Flash Point by Small Scale Closed or less than ( ) when analyzed in accordance with 8.1.
Cup Tester 6.1.2 Flash Point—The flash point of liquid products shall
be greater than ( ) when determined in accordance with 8.2.
1 6.1.3 Paste Hardness—The paste hardness shall be less than
This guide is under the jurisdiction of ASTM Committee D21 on Polishes and
is the direct responsibility of Subcommittee D21.05 on Specifications.
( ) when determined in accordance with 8.3.
Current edition approved Nov. 1, 2016. Published December 2016. Originally
6.1.4 Liquid Viscosity—The liquid wax shall be pourable
approved in 1979. Last previous edition approved in 2010 as D3757 – 89(2010).
within agreed temperature limits. See 8.4.
DOI: 10.1520/D3757-16.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on AvailablefromStandardizationDocumentsOrderDesk,Bldg.4SectionD,700
the ASTM website. Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D3757 − 16
4
Department of Labor’s (OSHA) regulations use Test Method D56 or
6.1.5 Odor—The product shall have no offensive odor. See
D3278 for liquids with a flash point of 37.8°C (100°F) and a viscosity of
8.4.
less
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D3757 − 89 (Reapproved 2010) D3757 − 16
Standard Guide for
1
Preparing Specifications for Solvent-based Floor Polishes
This standard is issued under the fixed designation D3757; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This is a guide for preparing specifications for solvent-based floor polishes (liquid or paste) that are intended for use on all
wood and solvent-resistant floors.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D56 Test Method for Flash Point by Tag Closed Cup Tester
D93 Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
D217 Test Methods for Cone Penetration of Lubricating Grease
D1455 Test Method for 60° Specular Gloss of Emulsion Floor Polish
D2047 Test Method for Static Coefficient of Friction of Polish-Coated Flooring Surfaces as Measured by the James Machine
D2834 Test Method for Nonvolatile Matter (Total Solids) in Water-Emulsion Floor Polishes, Solvent-Based Floor Polishes, and
Polymer-Emulsion Floor Polishes
D3206 Test Method for Soil Resistance of Floor Polishes
D3207 Test Method for Detergent Resistance of Floor Polish Films
D3278 Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
D3828 Test Methods for Flash Point by Small Scale Closed Cup Tester
3
2.2 Federal Specification:
Interim Federal Specification, Wax, General Purpose, Solvent Type, P-W-00158d (GSA-FSS) Amendment 1, July 13, 1972.
3. Significance and Use
3.1 This guide may be the basis for either the buying authority or the consumer to prepare a specification for solvent-based floor
polishes (liquid or paste). Specifications prepared under this guide are for products intended for use on all wood and solvent
resistant floors. Any reference material utilized and limits set are to be agreed upon by the seller, purchaser, or user.
4. Classification
4.1 Buffıng-Type Floor Polish—A floor polish that requires buffing to maintain or enhance appearance, or both.
4.2 Self-Polishing Floor Polish—A floor polish that dries to a shine.
5. Basis of Purchase
5.1 Identification of Samples—The qualification sample submitted by the manufacturer will be identified for the purpose of
comparing with material subsequently submitted for acceptance. Within test method limits, stated herein, qualification and
1
This guide is under the jurisdiction of ASTM Committee D21 on Polishes and is the direct responsibility of Subcommittee D21.05 on Specifications.
Current edition approved Sept. 1, 2010Nov. 1, 2016. Published September 2010December 2016. Originally approved in 1979. Last previous edition approved in 20052010
ε1
as D3757 – 89(2005)(2010). . DOI: 10.1520/D3757-89R10.10.1520/D3757-16.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D3757 − 16
acceptance samples should be identical. Any lot or lots found not to be identical with the standard sample shall be rejected.
Reference material is to be agreed upon between the purchaser and the seller.
6. Requirements
6.1 Physical (Product Specification Values or Limits):
6.1.1 Total Solids—The solids shall not be greater than ( ) or less than ( ) when analyzed in accordance with 8.1.
6.1.2 Flash Point—The flash point of liquid products shall be greater than ( ) when determined in accordance with 8.2.
6.1.3 Paste Hardness—The paste hardness shall be less than ( ) when determined in accordance with 8.3.
6.1.4 Liquid Viscosity—The liquid wax shall be pourable within agreed
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.