ASTM F2562/F2562M-15
(Specification)Specification for Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for Non-Pressure Drainage and Sewerage
Specification for Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for Non-Pressure Drainage and Sewerage
ABSTRACT
This specification covers requirements and test methods for materials, dimensions, workmanship, impact resistance, pipe stiffness, flattening, buckling, tensile strength of seam, joint systems, perforations, and markings for steel reinforced thermoplastic pipe and fittings. The steel reinforced, spirally formed thermoplastic pipes are intended for use in underground applications where soil provides support for their flexible walls. These pipes will be used for gravity flow and non-pressure applications, such as storm sewers, sanitary sewers, industrial waste applications and drainage pipes. The pipe dimensions, pipe stiffness, flattening, impact resistance, tensile strength of seam, and joint tightness shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, impact resistance, pipe stiffness, flattening, buckling, tensile strength of seam, joint systems, perforations, and markings for steel reinforced thermoplastic pipe and fittings of nominal sizes 8 in. [200 mm] through 120 in. [3000 mm]. The steel reinforced, spirally formed thermoplastic pipes governed by this standard are intended for use in underground applications where soil provides support for their flexible walls. These pipes will be used for gravity flow and non-pressure applications, such as storm sewers, sanitary sewers, industrial waste applications and drainage pipes.
1.2 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text the SI units are shown in brackets. The values stated in each system may not be exact equivalents: therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4 There is no similar or equivalent ISO standard.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F2562/F2562M −15
Specification for
Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for
1
Non-Pressure Drainage and Sewerage
ThisstandardisissuedunderthefixeddesignationF2562/F2562M;thenumberimmediatelyfollowingthedesignationindicatestheyear
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
1.1 This specification covers requirements and test methods
for materials, dimensions, workmanship, impact resistance,
2. Referenced Documents
pipe stiffness, flattening, buckling, tensile strength of seam, 2
2.1 ASTM Standards:
joint systems, perforations, and markings for steel reinforced
A1008/A1008M Specification for Steel, Sheet, Cold-Rolled,
thermoplastic pipe and fittings of nominal sizes 8 in. [200 mm]
Carbon, Structural, High-Strength Low-Alloy, High-
through 120 in. [3000 mm]. The steel reinforced, spirally
Strength Low-Alloy with Improved Formability, Solution
formed thermoplastic pipes governed by this standard are
Hardened, and Bake Hardenable
intended for use in underground applications where soil pro-
A1011/A1011M Specification for Steel, Sheet and Strip,
vides support for their flexible walls. These pipes will be used
Hot-Rolled, Carbon, Structural, High-Strength Low-
for gravity flow and non-pressure applications, such as storm
Alloy, High-Strength Low-Alloy with Improved
sewers, sanitary sewers, industrial waste applications and
Formability, and Ultra-High Strength
drainage pipes.
D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
1.2 Units—The values stated in either inch-pound units or
SI units are to be regarded separately as standard. Within the D2122 Test Method for Determining Dimensions of Ther-
moplastic Pipe and Fittings
text the SI units are shown in brackets. The values stated in
each system may not be exact equivalents: therefore, each D2321 PracticeforUndergroundInstallationofThermoplas-
tic Pipe for Sewers and Other Gravity-Flow Applications
system shall be used independently of the other. Combining
values from the two systems may result in non-conformance D2412 Test Method for Determination of External Loading
Characteristics of Plastic Pipe by Parallel-Plate Loading
with the standard.
D2444 Practice for Determination of the Impact Resistance
1.3 This standard does not purport to address all of the
of Thermoplastic Pipe and Fittings by Means of a Tup
safety concerns, if any, associated with its use. It is the
(Falling Weight)
responsibility of the user of this standard to establish appro-
D3212 Specification for Joints for Drain and Sewer Plastic
priate safety, health, and environmental practices and deter-
Pipes Using Flexible Elastomeric Seals
mine the applicability of regulatory limitations prior to use.
D3350 Specification for Polyethylene Plastics Pipe and Fit-
1.4 There is no similar or equivalent ISO standard.
tings Materials
1.5 This international standard was developed in accor-
F412 Terminology Relating to Plastic Piping Systems
dance with internationally recognized principles on standard-
F477 Specification for Elastomeric Seals (Gaskets) for Join-
ization established in the Decision on Principles for the
ing Plastic Pipe
Development of International Standards, Guides and Recom-
F2136 Test Method for Notched, Constant Ligament-Stress
(NCLS) Test to Determine Slow-Crack-Growth Resis-
tance of HDPE Resins or HDPE Corrugated Pipe
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
2
Piping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved April 15, 2015. Published July 2015. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2007. Last previous edition approved in 2008 as F2562/F2562M-08. Standards volume information, refer to the standard’s Document Summary page on
DOI: 10.1520/F2562_F2562M-15. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2562/F2562M−15
NOTE 1—Industrial waste disposal lines should be installed only upon
2.2 American Association of State Highway and Transpor-
3
the specific approval of the governing code, or other authority, and after
tation Offıcials (AASHTO)
determining the suitability of the product under the anticipated
AASHTO LRFD Bridge Construction Specification Section
environment, temperature, and other end-use condi
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2562/F2562M − 08 F2562/F2562M − 15
Specification for
Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for
1
Non-Pressure Drainage and Sewerage
This standard is issued under the fixed designation F2562/F2562M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, impact resistance, pipe
stiffness, flattening, buckling, tensile strength of seam, joint systems, perforations, and markings for steel reinforced thermoplastic
pipe and fittings of nominal sizes 8 in. [200 mm] through 120 in. [3000 mm]. The steel reinforced, spirally formed thermoplastic
pipes governed by this standard are intended for use in underground applications where soil provides support for their flexible
walls. These pipes will be used for gravity flow and non-pressure applications, such as storm sewers, sanitary sewers, industrial
waste applications and drainage pipes.
1.2 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text the
SI units are shown in brackets. The values stated in each system may not be exact equivalents: therefore, each system shall be used
independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1.4 There is no similar or equivalent ISO standard.
2. Referenced Documents
2
2.1 ASTM Standards:
A1008/A1008M Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength
Low-Alloy with Improved Formability, Solution Hardened, and Bake Hardenable
A1011/A1011M Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-
Strength Low-Alloy with Improved Formability, and Ultra-High Strength
D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling
Weight)
D3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
D3350 Specification for Polyethylene Plastics Pipe and Fittings Materials
F412 Terminology Relating to Plastic Piping Systems
F477 Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
F2136 Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE
Resins or HDPE Corrugated Pipe
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.11 on Composite.
Current edition approved March 1, 2008April 15, 2015. Published March 2008July 2015. Originally approved in 2007. Last previous edition approved in 20072008 as
F2562/F2562M-07.-08. DOI: 10.1520/F2562_F2562M-08.10.1520/F2562_F2562M-15.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2562/F2562M − 15
3
2.2 American Association of State Highway and Transportation Offıcials (AASHTO)
AASHTO LRFD Bridge Construction Specification Section 26
AASHTO M294-05 Corrugated Polyethylene Pipe, 300- to 1500-mm Diameter
4
2.3 Federal Standards:
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
2.4 Military Standards:
MIL-STD-129 Marking for Shipment and Storage
3. Terminolo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.