iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F2573-06

(Specification)

Standard Specification for Low Velocity Resilient Material Projectile

Standard Specification for Low Velocity Resilient Material Projectile

ABSTRACT
This specification covers critical characteristics of low velocity resilient material projectiles made from a resilient material. Material diameter, shape, projectile hardness, and weight shall conform to the dimensions indicated in this specification. This specification establishes minimum warning information, instructions, and package labeling for safety.
SCOPE
1.1 This specification covers critical characteristics of low velocity resilient material projectiles (herein referred to as LVRM projectiles) made of a resilient material, and shall have a diameter no smaller than 20 mm (0.7874 in) and no greater than 30 mm (1.18 in.), with a hardness no greater than 75 Shore 00 in accordance with Specification D 2240. This specification helps define whether a projectile is suitable for use with a low velocity projectile marker (herein referred to as LVP marker as defined in Specification F 2574). The weight of the LVRM projectile is not to exceed 4.0 g. Furthermore, this specification establishes minimum warning and package labeling to help ensure that the LVRM projectiles are used in a safe manner and that the risk of injury is reduced.
1.2 A LVRM projectile is not a paintball as defined in Section 2.1.2 of Specification F 1979.
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
30-Apr-2006
ICS
97.220.99 - Other sports equipment and facilities
Technical Committee
F08 - Sports Equipment, Playing Surfaces, and Facilities
Drafting Committee
F08.24 - Paintball and Equipment
Current Stage
Ref Project

Relations

Replaced By
ASTM F2573-06(2010) - Standard Specification for Low Velocity Resilient Material Projectile
Effective Date
01-Dec-2010
Referred By
ASTM F2574-06(2022) - Standard Specification for Low Velocity Projectile Marker
Effective Date
01-May-2006
Referred By
ASTM F2679-15(2023) - Standard Specification for 6 mm Projectiles Used with Airsoft Guns
Effective Date
01-May-2006
Referred By
ASTM F2654-23 - Standard Specification for Airsoft Gun Warnings
Effective Date
01-May-2006

Buy Standard

ASTM F2573-06 - Standard Specification for Low Velocity Resilient Material ProjectileASTM F2573-06 - Standard Specification for Low Velocity Resilient Material Projectile
PreviousNext
Technical specification
ASTM F2573-06 - Standard Specification for Low Velocity Resilient Material Projectile
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: F2573 – 06
Standard Specification for
Low Velocity Resilient Material Projectile
This standard is issued under the fixed designation F2573; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2.2 Federal Standards:
16 CFR 1500 Hazardous Substance Act Regulations
1.1 This specification covers critical characteristics of low
2.3 ANSI Standard:
velocity resilient material projectiles (herein referred to as
Z 535.1 Safety Color Code
LVRM projectiles) made of a resilient material, and shall have
a diameter no smaller than 20 mm (0.7874 in) and no greater
3. Terminology
than30mm(1.18in.),withahardnessnogreaterthan75Shore
3.1 Definitions of Terms Specific to This Standard:
00 in accordance with Specification D2240. This specification
3.1.1 low velocity projectile marker—device specifically
helps define whether a projectile is suitable for use with a low
designed to discharge LVRM projectiles. The device is some-
velocity projectile marker (herein referred to as LVPmarker as
times referred to as a low velocity projectile gun as defined in
defined in Specification F2574). The weight of the LVRM
Specification F2574.
projectile is not to exceed 4.0 g. Furthermore, this specification
3.1.2 low velocity resilient material ball—any spherical,
establishes minimum warning and package labeling to help
ovoid, or ellipsoidal object. The term “ball’ also includes any
ensurethattheLVRMprojectilesareusedinasafemannerand
multisided object formed by connecting planes into a generally
that the risk of injury is reduced.
spherical ovoid, or ellipsoidal shape that is designated or
1.2 A LVRM projectile is not a paintball as defined in
intended to be used as a ball. A “ball” can be a LVRM
Section 2.1.2 of Specification F1979.
projectile.
1.3 The values stated in SI units are to be regarded as the
3.1.3 low velocity resilient material projectile—object pro-
standard. The values given in parentheses are for information
pelled by means of a discharge mechanism capable of storing
only.
and releasing energy under the control of the operator com-
1.4 This standard does not purport to address all of the
prised of a resilient material, and have a diameter no smaller
safety concerns, if any, associated with its use. It is the
than 20 mm (0.7874 in) and no greater than 30 mm (1.18 in.).
responsibility of the user of this standard to establish appro-
The hardness of the LVRM projectile is to be no greater than
priate safety and health practices and to determine the
75 Shore 00 in accordance with Specification D2240. The
applicability of regulatory limitations prior to use.
weight of the LVRM projectile is not to exceed 4.0 g.
2. Referenced Documents 3.1.4 range—maximum distance to which an object may be
propelled, whether limited by energy or an obstacle.
2.1 ASTM Standards:
3.1.5 shore 00—applicable durometer type scale to measure
D2240 Test Method for Rubber Property—Durometer
the resistance of indentation and provide an empirical hardness
Hardness
value of sponge and foam materials in accordance with
F963 Consumer Safety Specification for Toy Safety
Specification D2240.
F1776 Specification for Eye Protective Devices for Paint-
ball Sports
4. General Requirements
F1979 Specification for Paintballs Used in the Sport of
4.1 Must be made of a resilient material.
Paintball
4.2 Must have a diameter no smaller than 20 mm (0.7874
F2574 Specification for Low Velocity Projectile Marker
in.) and no greater than 30 mm (1.18 in.).
This specification is under the jurisdiction of ASTM Committee F08 Sports
Equipment and Facilities and is the direct responsibility of Subcommittee F08.24 Available from U.S. Consumer Product Safety Commission (CPSC), 4330
Paintball and Equipment. East-West Hwy., Bethesda, MD 20814, website: www.cpsc.gov; or U.S. Govern-
Current edition approved May 1, 2006. Published May 2006. DOI: 10.1520/ ment Printing Office, Superintendent of Documents; P.O. Box 371954, Pittsburgh,
F2573-06. PA 15250-7954, website: www.gpo.gov.
2 4
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM 4th Floor, New York, NY 10036, website: www.ansi.org. Hard copies are available
Standards volume information, refer to the standard’s Document Summary page on from Global Engineering Documents, 15 Inverness Way, East Englewood, CO
the ASTM website. 80112-5704, website: www.gpo.gov.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
F2573 – 06
4.3 Hardness of projectile must not be greater than 75 Shore
00 in accordance with Specification D2240.
4.4 The weight is not to exceed 4.0 g.
4.5 No projectile intended to be expelled shall have any
sharp edges or sharp points.
4.6 No projectile expelled shall have a tip
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F2904-11(2023)(Specification)
Standard Specification for Warnings on Paintball Marker Accessories Used In the Sport of Paintball

ABSTRACT
This specification covers warnings used on paintball marker accessories used in the sport of paintball. It states that all of the paintball marker accessories for use in the sport of paintball shall include a cautionary statement which prominently and durably conveys certain information on the instruction sheet, the packaging, or the product itself, or a combination thereof.
SCOPE
1.1 This specification covers warnings used on paintball marker accessories used in the sport of paintball. The warnings contained in this standard are intended for products that do not have individual ASTM standards which contain product specific warnings.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F2574-06(2022)(Specification)
Standard Specification for Low Velocity Projectile Marker

ABSTRACT
This specification covers low velocity projectile (LVP) markers that eject a low velocity resilient material (LVRM) projectile using compressed air, compressed gas, or a combination of both. Included in this specification are performance requirements and test methods for LVP markers as well as the minimum warnings and instructions that need to be provided in literature, on labels, on packaging, and on the marker itself. The LVP markers shall be manufactured to operate only in semi-automatic or pump mode and with exposed edges that shall be smooth and free of sharp edges and burrs. LVP markers shall be provided with a disabling device which shall keep it from firing and with a provision against accidental discharge. The markers shall undergo tests for disabling device, accidental discharge, barrel blocking device, and impact, and shall conform to the requirements specified.
SCOPE
1.1 This specification covers low velocity projectile markers (herein referred to as LVP marker) that propel a low velocity resilient material projectile (herein referred to as LVRM projectile as defined in Specification F2573) by means of energy released by compressed air, compressed gas, or a combination thereof, with velocity not to exceed 53.34 m/s (175 ft/s).  
1.2 LVRM projectiles are made of a resilient material and have a diameter no smaller than 20 mm (0.7874 in.) and no greater than 30 mm (1.18 in.). The hardness of the LVRM projectile is to be no greater than 75 Shore 00. The weight of the LVRM projectile is not to exceed 4.0 g.  
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.4 The following precautionary caveat pertains only to the test method portion, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM F2573-06(2022)(Specification)
Standard Specification for Low Velocity Resilient Material Projectile

ABSTRACT
This specification covers critical characteristics of low velocity resilient material projectiles made from a resilient material. Material diameter, shape, projectile hardness, and weight shall conform to the dimensions indicated in this specification. This specification establishes minimum warning information, instructions, and package labeling for safety.
SCOPE
1.1 This specification covers critical characteristics of low velocity resilient material projectiles (herein referred to as LVRM projectiles) made of a resilient material, and shall have a diameter no smaller than 20 mm (0.7874 in.) and no greater than 30 mm (1.18 in.), with a hardness no greater than 75 Shore 00 in accordance with Specification D2240. This specification helps define whether a projectile is suitable for use with a low velocity projectile marker (herein referred to as LVP marker as defined in Specification F2574). The weight of the LVRM projectile is not to exceed 4.0 g. Furthermore, this specification establishes minimum warning and package labeling to help ensure that the LVRM projectiles are used in a safe manner and that the risk of injury is reduced.  
1.2 A LVRM projectile is not a paintball as defined in Section 2.1.2 of Specification F1979.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM F3543-22(Terminology)
Standard Terminology Relating to Hunting Saddles

SIGNIFICANCE AND USE
2.1 This standard is provided to develop and maintain uniformity of terminology for the discussion and evaluation of Hunting Saddles, particularly with regard to quality assurance and safety factors.  
2.2 The use of the terminology described will not alter the validity of data determined with specific test methods but provides guidance in the interpretation of test results (valid or invalid) and guidance in the selection of reasonable test procedures for those instances where no standard exists today.
SCOPE
1.1 This terminology covers terms related to hunting saddles.  
1.2 This terminology is appropriate for use by hunting saddle development professionals, owners and institutions, testing firms, users and other practitioners in matters concerning hunting saddle test methods, practices and specifications which fall under jurisdiction of ASTM Committee F08 on Sports Equipment and Facilities.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM F1979-17(2021)(Specification)
Standard Specification for Projectiles Used in the Sport of Paintball

ABSTRACT
This specification establishes testing procedures and critical characteristics of 0.68 caliber paintballs which help define whether a paintball is suitable for use in the sport of paintball. Furthermore, the specification establishes minimum warning and package labeling to help ensure that the paintballs are used in a safe manner and that the risk of injury is reduced. Tests shall be performed to conform with the requirements specified in accordance with the following test methods: paintball compatibility with polycarbonate and paintball impact breakage test.
SCOPE
1.1 This specification establishes testing procedures and critical characteristics for projectiles, which define whether they are suitable for use in the sport of paintball. Furthermore, the specification establishes minimum warning and package labeling requirements to help ensure that the paintballs are used in a safe manner and that the risk of injury is reduced.  
1.2 This specification does not cover non-recreational paintballs, for example, those used by law enforcement, scientific, military, or theatrical entities.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM F1750-16(2020)(Specification)
Standard Specification for Paintball Marker Threaded-Propellant Source Interface

ABSTRACT
This specification covers the male and female threaded connectors used to interface a propellant source to a paintball marker. The male connector shall incorporate a means for propellant shutoff that shall meet the maximum leakage requirement. When the male and female connectors are joined and pressurized, together they shall meet the maximum leakage specification. The male and female connector shall conform to the physical envelope described. The male connector may contain, as a means of propellant shutoff, a valve core to provide for an automatic shutoff of flow at the time of disconnection. The female connector shall have a provision for the self venting of residual gas pressure prior to the disconnection of the threaded interface.
SCOPE
1.1 This specification covers the male and female threaded connectors used to interface a propellant source with a normal working output pressure of 10 342 kPa (1800 psig) or less to a paintball marker.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM F2376-23(Practice)
Standard Practice for Classification, Design, Manufacture, Construction, and Operation of Water Slide Systems

SCOPE
1.1 This practice applies to the classification, design, manufacture, construction, auditing, major modification, and operation of water slide systems. Water slide systems shall be defined as rides intended for use by riders in bathing attire where the action of the ride involves possible and purposeful immersion of the rider's body either in whole or in part in water, and uses circulating water to mobilize or lubricate the rider’s transportation along a purpose built path. This includes slides used with or without vehicles as defined below. The terms water slides, waterslides, and slides shall be considered equivalent when used in this practice.  
1.1.1 Owner/operator requirements of this standard are required of all water slide systems regardless of date of construction.  
1.1.2 The design, manufacture and construction of an existing water slide or portions of a water slide system unaffected by a major modification shall meet the standard requirements in existence at the time of the construction.  
1.2 For the purposes of this practice, a water slide system includes:  
1.2.1 The flume,  
1.2.2 The water-circulation system,  
1.2.3 The starting platform with associated means of access and egress,  
1.2.4 The structural supports,  
1.2.5 Vehicles or other aquatic accessories that are part of the water slide as defined by the manufacturer, and  
1.2.6 Means of slide termination.  
1.3 This practice shall not apply to:  
1.3.1 Any water slides installed in private residences,  
1.3.2 Water flume amusement rides where contact with water is merely incidental (for example, log flume rides, shoot-the-chutes),  
1.3.3 Amusement rides and devices whose design criteria are specifically addressed in another ASTM standard,  
1.3.4 Lazy river type attractions operating at constant elevation, constructed in the ground,  
1.3.5 Inflatable water slides (constant air supply) that are mounted on land (refer to Practice F2374-22 for the requirements of these types of water slides),  
1.3.6 Inflatable water slides (captured air) that are floating on a body of water (refer to EN/ISO 25649-2017, parts 1 through 7), and  
1.3.7 Water slides less than 6 ft tall. (Refer to Practice F2461-20a for the requirements of slides less than 6 ft tall.)  
1.4 Pre-existing designs manufactured after the effective date of publication of this practice if the design is service proven or previously compliant, as defined in Terminology F747-22, and the manufacturer provides:  
1.4.1 A historical summary of the water slide, or major modification as defined in Terminology F747-22, and  
1.4.2 A statement that the design is service proven or previously compliant. Water slides and major modifications to water slides may qualify as previously compliant for five years following the date of publication of this practice. Thereafter, water slides and major modifications to water slides must qualify as service proven or meet the requirements of this practice.  
1.4.3 Service proven or previously compliant designs shall comply with Section 4.  
1.5 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
Note 1: The conversion factor from inch-pound to metric units is 1 in. = 25.4 mm, and 1 lb = 4.4482 N.  
1.6 This practice includes an Appendix, which provides additional information to enhance the user's understanding of and application of the criteria presented in this practice, for example, rationale, background, drawings, interpretation, or commentary. The information in the Appendix shall not be considered a mandatory part of this practice.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This intern...

  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    13 pages
    English language
    sale 15% off
ASTM
ASTM F2904-11(2023)(Specification)
Standard Specification for Warnings on Paintball Marker Accessories Used In the Sport of Paintball

ABSTRACT
This specification covers warnings used on paintball marker accessories used in the sport of paintball. It states that all of the paintball marker accessories for use in the sport of paintball shall include a cautionary statement which prominently and durably conveys certain information on the instruction sheet, the packaging, or the product itself, or a combination thereof.
SCOPE
1.1 This specification covers warnings used on paintball marker accessories used in the sport of paintball. The warnings contained in this standard are intended for products that do not have individual ASTM standards which contain product specific warnings.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F2573-06(2022)(Specification)
Standard Specification for Low Velocity Resilient Material Projectile

ABSTRACT
This specification covers critical characteristics of low velocity resilient material projectiles made from a resilient material. Material diameter, shape, projectile hardness, and weight shall conform to the dimensions indicated in this specification. This specification establishes minimum warning information, instructions, and package labeling for safety.
SCOPE
1.1 This specification covers critical characteristics of low velocity resilient material projectiles (herein referred to as LVRM projectiles) made of a resilient material, and shall have a diameter no smaller than 20 mm (0.7874 in.) and no greater than 30 mm (1.18 in.), with a hardness no greater than 75 Shore 00 in accordance with Specification D2240. This specification helps define whether a projectile is suitable for use with a low velocity projectile marker (herein referred to as LVP marker as defined in Specification F2574). The weight of the LVRM projectile is not to exceed 4.0 g. Furthermore, this specification establishes minimum warning and package labeling to help ensure that the LVRM projectiles are used in a safe manner and that the risk of injury is reduced.  
1.2 A LVRM projectile is not a paintball as defined in Section 2.1.2 of Specification F1979.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM F2574-06(2022)(Specification)
Standard Specification for Low Velocity Projectile Marker

ABSTRACT
This specification covers low velocity projectile (LVP) markers that eject a low velocity resilient material (LVRM) projectile using compressed air, compressed gas, or a combination of both. Included in this specification are performance requirements and test methods for LVP markers as well as the minimum warnings and instructions that need to be provided in literature, on labels, on packaging, and on the marker itself. The LVP markers shall be manufactured to operate only in semi-automatic or pump mode and with exposed edges that shall be smooth and free of sharp edges and burrs. LVP markers shall be provided with a disabling device which shall keep it from firing and with a provision against accidental discharge. The markers shall undergo tests for disabling device, accidental discharge, barrel blocking device, and impact, and shall conform to the requirements specified.
SCOPE
1.1 This specification covers low velocity projectile markers (herein referred to as LVP marker) that propel a low velocity resilient material projectile (herein referred to as LVRM projectile as defined in Specification F2573) by means of energy released by compressed air, compressed gas, or a combination thereof, with velocity not to exceed 53.34 m/s (175 ft/s).  
1.2 LVRM projectiles are made of a resilient material and have a diameter no smaller than 20 mm (0.7874 in.) and no greater than 30 mm (1.18 in.). The hardness of the LVRM projectile is to be no greater than 75 Shore 00. The weight of the LVRM projectile is not to exceed 4.0 g.  
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.4 The following precautionary caveat pertains only to the test method portion, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off