ASTM B517-03
(Specification)Standard Specification for Welded Nickel-Chromium-Iron-Alloy (UNS N06600, UNS N06603, UNS N06025, and UNS N06045) Pipe
Standard Specification for Welded Nickel-Chromium-Iron-Alloy (UNS N06600, UNS N06603, UNS N06025, and UNS N06045) Pipe
SCOPE
1.1 This specification covers welded, cold-worked, and annealed nickel-chromium-iron alloy (UNS N06600,* N06603, N06025, and N06045) pipe for general corrosive service and heat-resisting applications.
1.2 This specification covers outside diameter and nominal wall pipe shown in ANSI B36.19. Pipe having other dimensions may be furnished provided such pipe complies with all other requirements of this specification.
1.3 The values stated in inch-pound units are to be regarded as the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B 517 – 03
Standard Specification for
Welded Nickel-Chromium-Iron-Alloy (UNS N06600, UNS
1
N06603, UNS N06025, and UNS N06045) Pipe
This standard is issued under the fixed designation B 517; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope 4. General Requirement
2
1.1 This specification covers welded, cold-worked, and 4.1 Material furnished in accordance with this specification
annealed nickel-chromium-iron alloy (UNS N06600,* shall conform to the applicable requirements of the current
N06603, N06025, and N06045) pipe for general corrosive edition of Specification B 775 unless otherwise provided
service and heat-resisting applications. herein.
1.2 This specification covers outside diameter and nominal
5. Ordering Information
wall pipe shown in ANSI B36.19. Pipe having other dimen-
sions may be furnished provided such pipe complies with all 5.1 It is the responsibility of the purchaser to specify all
other requirements of this specification. requirements that are necessary for the safe and satisfactory
performance of material ordered under this specification.
1.3 The values stated in inch-pound units are to be regarded
as the standard. Examples of such requirements include, but are not limited to,
the following:
1.4 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the 5.1.1 Alloy name or UNS number.
5.1.2 ASTM designation and year of issue.
responsibility of the user of this standard to become familiar
with all hazards including those identified in the appropriate 5.1.3 Condition (temper).
5.1.4 Dimensions:
Material Safety Data Sheet for this product/material as pro-
vided by the manufacturer, to establish appropriate safety and 5.1.4.1 Nominal pipe size or outside diameter and schedule
number or nominal wall thickness.
health practices, and determine the applicability of regulatory
limitations prior to use. 5.1.4.2 Length (specific or random).
5.1.5 Quantity (feet or metres, or number of pieces).
2. Referenced Documents
5.1.6 Certification—State if certification or a report of test
2.1 ASTM Standards: results is required.
B 775 Specification for General Requirements for Nickel 5.1.7 Samples for Product (Check) Analysis—State whether
3
and Nickel Alloy Welded Pipe samples for product (check) analysis should be furnished.
B 899 Terminology Relating to Non-ferrous Metals and 5.1.8 Purchaser Inspection—If the purchaser wishes to
3
Alloys witness tests or inspection of material at the place of manu-
2.2 ANSI Standard: facture, the purchase order must so state indicating which tests
4
B36.19 Stainless Steel Pipe or inspections are to be witnessed.
3. Terminology 6. Materials and Manufacture
3.1 Terms defined in Terminology B 899 shall apply unless 6.1 Pipe shall be made from flat-rolled alloy by an auto-
defined otherwise in this standard. matic welding process with no addition of filler metal. Subse-
quent to welding and prior to final heat treatment, the material
shall be cold worked either in both weld and base metal or in
1
This specification is under the jurisdiction of ASTM Committee B02 on
weld metal only.
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
6.2 Pipe shall be furnished with a scale-free finish. When
B02.07 on Refined Nickel and Cobalt and Their Alloys.
Current edition approved July 10, 2003. Published August 2003. Originally
bright annealing is used, descaling is not necessary.
approved in 1970. Last previous edition approved in 1998 as B 517 - 98.
2
For ASME Boiler and Pressure Code applications see related Specification
7. Chemical Composition
SB-517 in Section II of that Code.
* New designation established in accordance withASTM E 527 and SAE J1086, 7.1 The material shall conform to the requirements as to
Practice for Numbering Metals and Alloys (UNS).
chemical composition prescribed in Table 1.
3
Annual Book of ASTM Standards, Vol 02.04.
4
Available fromAmerican National Standards Institute, 11W. 42nd St., 13th Fl.,
New York, NY 10036.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B517–03
TABLE 1 Chemical Requirements
Composition Product (Check) Analysis
Limits,% Variations, under min or
Element
over max, of the
N06600 N06603 N06025 N06045
Specified Limit of Element
A
Nickel 72.0 min Bal Bal 45.0 min 0.45
Chromium 14.0 min 24.0–26.0 24.0–26.0 26.0–29.0 0.15
17.0 max 0.25
Iron 6.0 min 8.0–11.0 8.0–11.0 21.0–25.0 0.10
10.0 max 0.10
Manganese 1.0 0.15 max 0.15 max 1.0
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.