ASTM B775/B775M-22
(Specification)Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe
Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe
ABSTRACT
This general specification contains the mandatory requirements to the ASTM standards listed herein for longitudinally welded piping made from nickel and nickel alloys. In case of conflict, the requirements listed in the particular product specification takes precedence over those listed here.
SCOPE
1.1 This specification contains various requirements that, with the exception of Section 5 and Section 10, are mandatory requirements to the following ASTM nickel and nickel alloy, longitudinally welded piping specifications:2
Title of Specification
ASTM
Designation2
Welded UNS N08020 Alloy Pipe
B464/B464M
Welded Nickel-Iron-Chromium Alloy Pipe
B514
Welded Nickel-Chromium-Iron-Alloy (UNS N06600,
UNS N06603, UNS N06025 and UNS N06045) Pipe
B517
Welded Nickel and Nickel-Cobalt Alloy Pipe
B619/B619M
UNS N08904, UNS N08925, and UNS N08926 Welded Pipe
B673
UNS N08367 Welded Pipe
B675
Nickel-Alloy (UNS N06625, N06219, and N08825) Welded Pipe
B705
Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Welded Pipe
B723
Welded Nickel (UNS N02200/UNS N02201) and Nickel
Copper Alloy (UNS N04400) Pipe
B725
1.2 One or more of the test requirements of Section 5 apply only if specifically stated in the product specification or in the purchase order.
1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only the requirement of the product specification needs to be satisfied.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:B775/B775M −22
Standard Specification for
General Requirements for Nickel and Nickel Alloy Welded
1
Pipe
This standard is issued under the fixed designation B775/B775M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* responsibility of the user of this standard to become familiar
with all hazards including those identified in the appropriate
1.1 This specification contains various requirements that,
Safety Data Sheet (SDS) for this product/material as provided
with the exception of Section 5 and Section 10, are mandatory
by the manufacturer, to establish appropriate safety, health,
requirements to the following ASTM nickel and nickel alloy,
2
and environmental practices, and determine the applicability
longitudinally welded piping specifications:
of regulatory limitations prior to use.
ASTM
2
Title of Specification Designation
1.6 This international standard was developed in accor-
dance with internationally recognized principles on standard-
Welded UNS N08020 Alloy Pipe B464/B464M
ization established in the Decision on Principles for the
Welded Nickel-Iron-Chromium Alloy Pipe B514
Welded Nickel-Chromium-Iron-Alloy (UNS N06600, B517
Development of International Standards, Guides and Recom-
UNS N06603, UNS N06025 and UNS N06045) Pipe
mendations issued by the World Trade Organization Technical
Welded Nickel and Nickel-Cobalt Alloy Pipe B619/B619M
UNS N08904, UNS N08925, and UNS N08926 Welded Pipe B673
Barriers to Trade (TBT) Committee.
UNS N08367 Welded Pipe B675
Nickel-Alloy (UNS N06625, N06219, and N08825) Welded B705
2. Referenced Documents
Pipe
Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Welded Pipe B723
2
Welded Nickel (UNS N02200/UNS N02201) and Nickel B725 2.1 ASTM Standards:
Copper Alloy (UNS N04400) Pipe
B168 Specification for Nickel-Chromium-AluminumAlloys
1.2 One or more of the test requirements of Section 5 apply
(UNS N06699), Nickel-Chromium-Iron Alloys (UNS
only if specifically stated in the product specification or in the
N06600, N06601, N06603, N06690, N06693, N06025,
purchase order.
N06045, and N06696), Nickel-Chromium-Cobalt-
Molybdenum Alloy (UNS N06617), Nickel-Iron-
1.3 In case of conflict between a requirement of the product
Chromium-Tungsten Alloy (UNS N06674), and Nickel-
specification and a requirement of this general specification,
Chromium-Molybdenum-Copper Alloy (UNS N06235)
only the requirement of the product specification needs to be
satisfied. Plate, Sheet, and Strip
B464/B464M Specification for Welded UNS N08020 Alloy
1.4 The values stated in either SI units or inch-pound units
Pipe
are to be regarded separately as standard. The values stated in
B514 SpecificationforWeldedNickel-Iron-ChromiumAlloy
each system are not necessarily exact equivalents; therefore, to
Pipe
ensure conformance with the standard, each system shall be
B517 Specification for Welded Nickel-Chromium-Iron-
used independently of the other, and values from the two
Alloy Pipe
systems shall not be combined.
B619/B619M Specification for Welded Nickel and Nickel-
1.5 This standard does not purport to address all of the
Cobalt Alloy Pipe
safety concerns, if any, associated with its use. It is the
B673 Specification for Nickel-Iron-Chromium-
Molybdenum and Iron-Nickel-Chromium-Molybdenum-
1
Copper Welded Pipe
This specification is under the jurisdiction of ASTM Committee B02 on
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
B675 Specification for UNS N08367 Welded Pipe
B02.07 on Refined Nickel and Cobalt and Their Alloys.
B705 SpecificationforNickel-Alloy(UNSN06625,N06219
Current edition approved April 1, 2022. Published April 2022. Originally
and N08825) Welded Pipe
approved in 1987. Last previous edition approved in 2019 as B775/B775M – 19.
DOI: 10.1520/B0775_B0775M-22.
B723 Specification for Nickel-Chromium-Molybdenum-
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Cobalt-Tungsten-Iron-Silicon Alloy Welded Pipe
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
B725 Specification for Welded Nickel (UNS N02200/UNS
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. N02201) and Nickel Copper Alloy (UNS N04400) Pipe
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 -------
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B775/B775M − 19 B775/B775M − 22
Standard Specification for
General Requirements for Nickel and Nickel Alloy Welded
1
Pipe
This standard is issued under the fixed designation B775/B775M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification contains various requirements that, with the exception of Section 5 and Section 10, are mandatory
2
requirements to the following ASTM nickel and nickel alloy, longitudinally welded piping specifications:
ASTM
2
Title of Specification Designation
Welded UNS N08020 Alloy Pipe B464/B464M
Welded Nickel-Iron-Chromium Alloy Pipe B514
Welded Nickel-Chromium-Iron-Alloy (UNS N06600, B517
UNS N06603, UNS N06025 and UNS N06045) Pipe
Welded Nickel and Nickel-Cobalt Alloy Pipe B619/B619M
UNS N08904, UNS N08925, and UNS N08926 Welded Pipe B673
UNS N08367 Welded Pipe B675
Nickel-Alloy (UNS N06625, N06219, and N08825) Welded B705
Pipe
Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Welded Pipe B723
Welded Nickel (UNS N02200/UNS N02201) and Nickel B725
Copper Alloy (UNS N04400) Pipe
1.2 One or more of the test requirements of Section 5 apply only if specifically stated in the product specification or in the purchase
order.
1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only the
requirement of the product specification needs to be satisfied.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used
independently of the other, and values from the two systems shall not be combined.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet
(SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental
practices, and determine the applicability of regulatory limitations prior to use.
1
This specification is under the jurisdiction of ASTM Committee B02 on Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee B02.07 on Refined
Nickel and Cobalt and Their Alloys.
Current edition approved April 1, 2019April 1, 2022. Published April 2019April 2022. Originally approved in 1987. Last previous edition approved in 20162019 as
B775/B775M – 16.B775/B775M – 19. DOI: 10.1520/B0775_B0775M-19.10.1520/B0775_B0775M-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B775/B775M − 22
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
B168 Specification for Nickel-Chromium-Aluminum Alloys (UNS N06699), Nickel-Chromium-Iron Alloys (UNS N06600,
N06601, N06603, N06690, N06693, N06025, N06045, and N06696), Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS
N06617), Nickel-Iron-Chromium-Tungsten Alloy (UNS N06674), and Nickel-Chromium-Molybdenum-Copper Alloy (UNS
N06235) Plate, Sheet, and Strip
B464/B464M Specification for Welded UNS N08020 Alloy Pipe
B514 Specification for Welded Nickel-Iron-Chromium Alloy Pipe
B517 Specification for Welded Nickel-Chromium-Iron-Alloy Pipe
B619/B619M Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe
B673 Specification for Nickel-Iron-Chromium-Molybdenum and Iron-Nickel-Chromium-Molybdenum-Copper Welded Pipe
B675 Specification for UNS N08367 Welded Pipe
B705 Specification for Nickel-Alloy (UNS N
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.