ASTM F3219-18
(Specification)Standard Specification for 3 to 30 in. (75 To 750 mm) Polypropylene (PP) Corrugated Single Wall Pipe and Fittings
Standard Specification for 3 to 30 in. (75 To 750 mm) Polypropylene (PP) Corrugated Single Wall Pipe and Fittings
SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, elongation, brittleness, pipe stiffness, and markings for single wall corrugated polypropylene (PP) pipe and fittings. It covers nominal sizes 3 in. through 30 in. (75 mm through 750 mm)
1.2 The corrugated polypropylene pipe and fittings are for use in non-pressure gravity applications, including leach field effluent disposal, and drainage applications such as land, roads, foundations, agricultural, and landfill.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F3219 −18
Standard Specification for
3 to 30 in. (75 To 750 mm) Polypropylene (PP) Corrugated
1
Single Wall Pipe and Fittings
This standard is issued under the fixed designation F3219; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D790 Test Methods for Flexural Properties of Unreinforced
and Reinforced Plastics and Electrical Insulating Materi-
1.1 This specification covers requirements and test methods
als
for materials, dimensions, workmanship, elongation,
D792 Test Methods for Density and Specific Gravity (Rela-
brittleness, pipe stiffness, and markings for single wall corru-
tive Density) of Plastics by Displacement
gated polypropylene (PP) pipe and fittings. It covers nominal
D1238 Test Method for Melt Flow Rates of Thermoplastics
sizes 3 in. through 30 in. (75 mm through 750 mm)
by Extrusion Plastometer
1.2 The corrugated polypropylene pipe and fittings are for
D1505 Test Method for Density of Plastics by the Density-
use in non-pressure gravity applications, including leach field
Gradient Technique
effluent disposal, and drainage applications such as land, roads,
D1600 Terminology forAbbreviatedTerms Relating to Plas-
foundations, agricultural, and landfill.
tics
D2122 Test Method for Determining Dimensions of Ther-
1.3 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical moplastic Pipe and Fittings
D2321 PracticeforUndergroundInstallationofThermoplas-
conversions to SI units that are provided for information only
and are not considered standard. tic Pipe for Sewers and Other Gravity-Flow Applications
D2412 Test Method for Determination of External Loading
1.4 This standard does not purport to address all of the
Characteristics of Plastic Pipe by Parallel-Plate Loading
safety concerns, if any, associated with its use. It is the
D2444 Practice for Determination of the Impact Resistance
responsibility of the user of this standard to establish appro-
of Thermoplastic Pipe and Fittings by Means of a Tup
priate safety, health, and environmental practices and deter-
(Falling Weight)
mine the applicability of regulatory limitations prior to use.
D3895 Test Method for Oxidative-Induction Time of Poly-
1.5 This international standard was developed in accor-
olefins by Differential Scanning Calorimetry
dance with internationally recognized principles on standard-
D4101 Classification System and Basis for Specification for
ization established in the Decision on Principles for the
Polypropylene Injection and Extrusion Materials
Development of International Standards, Guides and Recom-
F412 Terminology Relating to Plastic Piping Systems
mendations issued by the World Trade Organization Technical
F449 Practice for Subsurface Installation of Corrugated
Barriers to Trade (TBT) Committee.
Polyethylene Pipe for Agricultural Drainage or Water
2. Referenced Documents Table Control
F477 Specification for Elastomeric Seals (Gaskets) for Join-
2
2.1 ASTM Standards:
ing Plastic Pipe
D256 Test Methods for Determining the Izod Pendulum
3
2.2 AASHTO Standard:
Impact Resistance of Plastics
AASHTO LRFD Bridge Design Specifications
D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
3. Terminology
3.1 Definitions are in accordance with Terminology F412
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
and abbreviations are accordance with Terminology D1600,
Piping Systems and is the direct responsibility of Subcommittee F17.65 on Land
unless otherwise specified.
Drainage.
Current edition approved Nov. 1, 2018. Published January 2019. Originally
3.2 Definitions of Terms Specific to This Standard:
approved in 2017. Last previous edition approved in 2017 as F3219–17. DOI:
10.1520/F3219–18
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from American Association of State Highway and Transportation
Standards volume information, refer to the standard’s Document Summary page on Officials (AASHTO), 444 N. Capitol St., NW, Suite 249, Washington, DC 20001,
the ASTM website. http://www.transportation.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F3219−18
TABLE 1 Polypropylene Compound Properties
3.2.1 single wall pipe, n—corrugated pipe without an inte-
rior or exterior li
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F3219 − 17 F3219 − 18
Standard Specification for
3 to 30 in. (75 To 750 mm) Polypropylene (PP) Corrugated
1
Single Wall Pipe and Fittings
This standard is issued under the fixed designation F3219; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Scope*
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, elongation, brittleness,
pipe stiffness, and markings for single wall corrugated polypropylene (PP) pipe and fittings. It covers nominal sizes 3 in. through
30 in. (75 mm through 750 mm)
1.2 The corrugated polypropylene pipe and fittings are for use in non-pressure gravity applications, including leach field effluent
disposal, and drainage applications such as land, roads, foundations, agricultural, and landfill.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D1238 Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
D1505 Test Method for Density of Plastics by the Density-Gradient Technique
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling
Weight)
D3895 Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry
D4101 Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials
F412 Terminology Relating to Plastic Piping Systems
F449 Practice for Subsurface Installation of Corrugated Polyethylene Pipe for Agricultural Drainage or Water Table Control
F477 Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
1
This test method specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.65 on
Land Drainage.
Current edition approved Nov. 15, 2017Nov. 1, 2018. Published February 2018January 2019. Originally approved in 2017. Last previous edition approved in 2017 as
F3219–17. DOI: 10.1520/F3219–1710.1520/F3219–18
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F3219 − 18
3
2.2 AASHTO Standard:
AASHTO LRFD Bridge Design Specifications
3. Terminology
3.1 Definitions are in accordance with Terminology F412 and abbreviations are accordance with Terminology D1600, unless
otherwise specified.
3.2 Definitions of
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.