ASTM F3219-19
(Specification)Standard Specification for 3 to 30 in. (75 To 750 mm) Polypropylene (PP) Corrugated Single Wall Pipe and Fittings
Standard Specification for 3 to 30 in. (75 To 750 mm) Polypropylene (PP) Corrugated Single Wall Pipe and Fittings
ABSTRACT
This specification covers the general requirements and test methods for materials, dimensions, workmanship, elongation, brittleness, pipe stiffness, and markings for single wall corrugated polypropylene (PP) pipe and fittings used in non-pressure gravity applications, including leach field effluent disposal, and drainage applications such as land, roads, foundations, agricultural, and landfill. It applies to PP corrugated single wall pipe and fittings with nominal sizes 3 in. through 30 in. (75 mm through 750 mm). This specification includes minimum properties for PP compounds used in the manufacture of corrugated single wall pipes, as well as nominal pipe sizes, inside diameters and tolerances for single wall corrugated PP pipes. It also covers fittings and joining system requirements, installation requirements, sampling and retest, certification, reporting, packaging, and quality assurance.
SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, elongation, brittleness, pipe stiffness, and markings for single wall corrugated polypropylene (PP) pipe and fittings. It covers nominal sizes 3 in. through 30 in. (75 mm through 750 mm)
1.2 The corrugated polypropylene pipe and fittings are for use in non-pressure applications where soil-tight joints are acceptable, such as leach field effluent disposal, and drainage applications such as land, roads, foundations, agricultural, and landfill. Products meeting this specification are not suitable for applications requiring water-tight joints unless the manufacturer offers such joints as an option.
Note 1: Watertight joints, when requested or specified, should meet a 10.8 psi (74 kPa) laboratory internal and external pressure in accordance with Specification D3212 and should utilize a bell and spigot design with a gasket that complies with Specification F477.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F3219 −19
Standard Specification for
3 to 30 in. (75 To 750 mm) Polypropylene (PP) Corrugated
1
Single Wall Pipe and Fittings
This standard is issued under the fixed designation F3219; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
2.1 ASTM Standards:
1.1 This specification covers requirements and test methods
D256 Test Methods for Determining the Izod Pendulum
for materials, dimensions, workmanship, elongation,
Impact Resistance of Plastics
brittleness, pipe stiffness, and markings for single wall corru-
D618 Practice for Conditioning Plastics for Testing
gated polypropylene (PP) pipe and fittings. It covers nominal
D638 Test Method for Tensile Properties of Plastics
sizes 3 in. through 30 in. (75 mm through 750 mm)
D790 Test Methods for Flexural Properties of Unreinforced
1.2 The corrugated polypropylene pipe and fittings are for and Reinforced Plastics and Electrical Insulating Materi-
use in non-pressure applications where soil-tight joints are als
D792 Test Methods for Density and Specific Gravity (Rela-
acceptable, such as leach field effluent disposal, and drainage
tive Density) of Plastics by Displacement
applications such as land, roads, foundations, agricultural, and
D1238 Test Method for Melt Flow Rates of Thermoplastics
landfill. Products meeting this specification are not suitable for
by Extrusion Plastometer
applications requiring water-tight joints unless the manufac-
D1505 Test Method for Density of Plastics by the Density-
turer offers such joints as an option.
Gradient Technique
NOTE 1—Watertight joints, when requested or specified, should meet a D1600 Terminology forAbbreviatedTerms Relating to Plas-
10.8 psi (74 kPa) laboratory internal and external pressure in accordance
tics
with Specification D3212 and should utilize a bell and spigot design with
D2122 Test Method for Determining Dimensions of Ther-
a gasket that complies with Specification F477.
moplastic Pipe and Fittings
D2321 PracticeforUndergroundInstallationofThermoplas-
1.3 The values stated in inch-pound units are to be regarded
tic Pipe for Sewers and Other Gravity-Flow Applications
as standard. The values given in parentheses are mathematical
D2412 Test Method for Determination of External Loading
conversions to SI units that are provided for information only
Characteristics of Plastic Pipe by Parallel-Plate Loading
and are not considered standard.
D2444 Practice for Determination of the Impact Resistance
1.4 This standard does not purport to address all of the
of Thermoplastic Pipe and Fittings by Means of a Tup
safety concerns, if any, associated with its use. It is the
(Falling Weight)
responsibility of the user of this standard to establish appro-
D3212 Specification for Joints for Drain and Sewer Plastic
priate safety, health, and environmental practices and deter-
Pipes Using Flexible Elastomeric Seals
mine the applicability of regulatory limitations prior to use.
D3895 Test Method for Oxidative-Induction Time of Poly-
olefins by Differential Scanning Calorimetry
1.5 This international standard was developed in accor-
D4101 Classification System and Basis for Specification for
dance with internationally recognized principles on standard-
Polypropylene Injection and Extrusion Materials
ization established in the Decision on Principles for the
F412 Terminology Relating to Plastic Piping Systems
Development of International Standards, Guides and Recom-
F449 Practice for Subsurface Installation of Corrugated
mendations issued by the World Trade Organization Technical
Polyethylene Pipe for Agricultural Drainage or Water
Barriers to Trade (TBT) Committee.
Table Control
F477 Specification for Elastomeric Seals (Gaskets) for Join-
ing Plastic Pipe
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.65 on Land
2
Drainage. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved April 1, 2019. Published April 2019. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2017. Last previous edition approved in 2018 as F3219–18. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/F3219–19 the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Driv
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F3219 − 18 F3219 − 19
Standard Specification for
3 to 30 in. (75 To 750 mm) Polypropylene (PP) Corrugated
1
Single Wall Pipe and Fittings
This standard is issued under the fixed designation F3219; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, elongation, brittleness,
pipe stiffness, and markings for single wall corrugated polypropylene (PP) pipe and fittings. It covers nominal sizes 3 in. through
30 in. (75 mm through 750 mm)
1.2 The corrugated polypropylene pipe and fittings are for use in non-pressure gravity applications, including applications where
soil-tight joints are acceptable, such as leach field effluent disposal, and drainage applications such as land, roads, foundations,
agricultural, and landfill. Products meeting this specification are not suitable for applications requiring water-tight joints unless the
manufacturer offers such joints as an option.
NOTE 1—Watertight joints, when requested or specified, should meet a 10.8 psi (74 kPa) laboratory internal and external pressure in accordance with
Specification D3212 and should utilize a bell and spigot design with a gasket that complies with Specification F477.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D1238 Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
D1505 Test Method for Density of Plastics by the Density-Gradient Technique
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling
Weight)
D3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
D3895 Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.65 on Land Drainage.
Current edition approved Nov. 1, 2018April 1, 2019. Published January 2019April 2019. Originally approved in 2017. Last previous edition approved in 20172018 as
F3219–17.–18. DOI: 10.1520/F3219–1810.1520/F3219–19
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F3219 − 19
D4101 Classification System a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.