ASTM B280-02

Standard Specification for Seamless Copper Tube for Air Conditioning and Refrigeration Field Service

SCOPE
1.1 This specification establishes the requirements for seamless copper tube produced from Copper UNS No. C12200 and intended for use in the connection, repairs, or alternations of air conditioning or refrigeration units in the field.
Note 1—Fittings used for soldered or brazed connections in air conditioning and refrigeration systems are described in ASME Standard B16.22.
Note 2—The assembly of copper tubular systems by soldering is described in Practice B 828.
Note 3—Solders for joining copper tubular systems are described in Specification B 32. The requirements for acceptable fluxes for these systems are described in Specification B 813.
1.2 Values stated in inch-pound units are the standard except for grain size which is stated in SI units. SI values given in parentheses are for information only.
1.3 The following hazard statement pertains only to the test method described in Section 18.2.4 of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 09-Oct-2002
• ICS: 23.040.15 - Non-ferrous metal pipes
• Technical Committee: B05 - Copper and Copper Alloys
• Drafting Committee: B05.04 - Pipe and Tube

Relations

• Replaced By: ASTM B280-03 - Standard Specification for Seamless Copper Tube for Air Conditioning and Refrigeration Field Service
• Effective Date: 01-Oct-2003

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B 280 – 02
Standard Specification for
Seamless Copper Tube for Air Conditioning and
1
Refrigeration Field Service
This standard is issued under the fixed designation B 280; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (ε) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
4
1. Scope * E 3 Guide for Preparation of Metallographic Specimens
4
E 8 Test Methods forTensionTesting of Metallic Materials
1.1 Thisspecificationestablishestherequirementsforseam-
E 29 Practice for Using Significant Digits in Test Data to
less copper tube produced from Copper UNS No. C12200 and
5
Determine Conformance with Specifications
intendedforuseintheconnection,repairs,oralternationsofair
E 53 Test Methods for Determination of Copper in Unal-
conditioning or refrigeration units in the field.
6
loyed Copper by Gravimetry
NOTE 1—Fittings used for soldered or brazed connections in air
E 62 Test Methods for Chemical Analysis of Copper and
conditioning and refrigeration systems are described in ASME Standard
6
Copper Alloys (Photometric Method)
B16.22.
E 112 Test Methods for Determining the Average Grain
NOTE 2—The assembly of copper tubular systems by soldering is
4
Size
described in Practice B 828.
E 243 Practice for Electromagnetic (Eddy-Current) Exami-
NOTE 3—Solders for joining copper tubular systems are described in
7
Specification B 32. The requirements for acceptable fluxes for these
nation of Seamless Copper and Copper-Alloy Tubes
systems are described in Specification B 813.
E 255 Practice for Sampling Copper and CopperAlloys for
6
Determination of Chemical Composition
1.2 Valuesstatedininch-poundunitsarethestandardexcept
8
E 527 Practice for Numbering Metals and Alloys (UNS)
for grain size which is stated in SI units. SI values given in
9
2.2 ASME Standards:
parentheses are for information only.
B1622 Wrought Copper and Copper Alloy Solder Joint
1.3 The following hazard statement pertains only to the test
Pressure Fittings
method described in Section 18.2.4 of this specification: This
standard does not purport to address all of the safety concerns,
3. Terminology
if any, associated with its use. It is the responsibility of the user
3.1 Definitions:
of this standard to establish appropriate safety and health
3.1.1 average diameter (for round tubes only), n—the
practices and determine the applicability of regulatory limita-
average of the maximum and minimum outside diameters, or
tions prior to use.
maximum and minimum inside diameters, whichever is appli-
2. Referenced Documents
cable, as determined at any one cross section of the tube.
3.1.2 bright anneal, n—a thermal treatment carried out in a
2.1 ASTM Standards:
2
controlled atmosphere so that surface oxidation is reduced to a
B 32 Specification for Solder Metal
minimum and the surface remains relatively bright.
B 153 Test Method for Expansion (Pin Test) of Copper and
3
3.1.3 coil, n—a length of the product wound into a series of
Copper-Alloy Pipe and Tube
connected turns. The unqualified term “coil” as applied to tube
B 601 Classification for Temper Designations for Copper
3
usually refers to a bunched coil.
and Copper Alloys—Wrought and Cast
3.1.3.1 bunched, n—a coil in which the turns are bunched
B 813 Specification for Liquid and Paste Fluxes for Solder-
3
and held together such that the cross section of the bunched
ing Applications of Copper and Copper Alloy Tube
turns is approximately circular.
B 828 Practice for Making Capillary Joints by Soldering of
3
Copper and Copper Alloy Tube and Fittings
1 4
ThisspecificationisunderthejurisdictionofASTMCommitteeB05onCopper Annual Book of ASTM Standards, Vol 03.01.
5
and CopperAlloys and is the direct responsibility of Subcommittee B05.04 on Pipe Annual Book of ASTM Standards, Vol 14.02.
6
and Tube. Annual Book of ASTM Standards, Vol 03.06.
7
Current edition approved Oct. 10, 2002. Published November 2002. Originally Annual Book of ASTM Standards, Vol 03.03.
ε1 8
published as B 280 – 53T. Last previous edition B 280 – 99 . Annual Book of ASTM Standards, Vol 01.01.
2 9
Annual Book of ASTM Standards, Vol 02.04. Available from American Society of Mechanical Engineers (ASME), ASME
3
Annual Book of ASTM Standards, Vol 02.01. International Headquarters, Three Park Ave., New York, NY 10016-5990.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
B280–02
3.1.3.2 level or traverse wound, n—a coil in which the t
...