iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D4383-02

(Specification)

Standard Specification for Plowable, Raised Retroreflective Pavement Markers

Standard Specification for Plowable, Raised Retroreflective Pavement Markers

SCOPE
1.1 This specification covers a type of plowable, retroreflective, raised pavement marker for lane marking and delineation.
1.2 Retroreflective markers are intended for nighttime visibility.
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 The following precautionary caveat pertains only to the test methods portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
09-Jul-2002
ICS
93.080.20 - Road construction materials
Technical Committee
D04 - Road and Paving Materials
Drafting Committee
D04.38 - Highway Traffic Control Materials
Current Stage
Ref Project

Relations

Replaces
ASTM D4383-01 - Standard Specification for Plowable, Raised Retroreflective Pavement Markers
Effective Date
10-Jul-2002
Replaced By
ASTM D4383-03 - Standard Specification for Plowable, Raised Retroreflective Pavement Markers
Effective Date
01-Dec-2003

Buy Standard

ASTM D4383-02 - Standard Specification for Plowable, Raised Retroreflective Pavement MarkersASTM D4383-02 - Standard Specification for Plowable, Raised Retroreflective Pavement Markers
PreviousNext
Technical specification
ASTM D4383-02 - Standard Specification for Plowable, Raised Retroreflective Pavement Markers
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: D 4383 – 02
Standard Specification for
1
Plowable, Raised Retroreflective Pavement Markers
This standard is issued under the fixed designation D 4383; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
5
1. Scope Materials (Thin-Film Oven Test)
D 1856 Test Method for Recovery of Asphalt from Solution
1.1 This specification covers a type of plowable, retroreflec-
5
by Abson Method
tive, raised pavement marker for lane marking and delineation.
D 2171 Test Method for Viscosity of Asphalts by Vacuum
1.2 Retroreflective markers are intended for nighttime vis-
5
Capillary Viscometer
ibility.
D 2669 Test Method for Apparent Viscosity of Petroleum
1.3 The values stated in SI units are to be regarded as the
9
Waxes Compounded with Additives (Hot Melts)
standard. The values given in parentheses are for information
D 2712 Test Method for Hydrocarbon Traces in Propylene
only.
9
Concentrates by Gas Chromatography
1.4 The following precautionary caveat pertains only to the
D 3407 Test Methods for Joint Sealants, Hot-Poured, for
test methods portion, Section 10, of this specification: This
10
Concrete and Asphalt Pavements
standard does not purport to address all of the safety concerns,
D 3935 Specification for Polycarbonate (PC) Unfilled and
if any, associated with its use. It is the responsibility of the user
11
Reinforced Material
of this standard to establish appropriate safety and health
D 4402 Test Method for Viscosity Determination of As-
practices and determine the applicability of regulatory limita-
phalts at Elevated Temperatures Using a Rotational Vis-
tions prior to use.
6
cometer
2. Referenced Documents
E 18 Test Methods for Rockwell Hardness and Rockwell
12
Superficial Hardness of Metallic Materials
2.1 ASTM Standards:
13
2
E 284 Terminology of Appearance
A 536 Specification for Ductile Iron Castings
E 308 Practice for Computing the Colors of Objects by
C 184 Test Method for Fineness of Hydraulic Cement by
13
3
Using the CIE System
the 150-μm (No. 100) and 75-μm (No. 200) Sieves
13
E 808 Practice for Describing Retroreflection
C 430 Test Method for Fineness of Hydraulic Cement by
4
E 809 Practice for Measuring Photometric Characteristics
the 45-μm (No. 325) Sieve
13
5
of Retroreflectors
D 5 Test Method for Penetration of Bituminous Materials
E 811 Practice for Measuring Colorimetric Characteristics
D 36 Test Method for Softening Point of Bitumen (Ring-
13
6
of Retroreflectors Under Nighttime Conditions
and-Ball Apparatus)
14
2.2 Federal Specifications:
D 70 Test Method for Specific Gravity and Density of
5
FF-W-1825A Wool and Gauze, Metallic
Semi-Solid Bituminous Materials (Pycnometer Method)
TT-T-291 Thinner, Paint, Mineral Spirits, Regular and
D 92 Test Method for Flash and Fire Points by Cleveland
7
Odorless
Open Cup
15
2.3 AASHTO Standards:
D 788 Classification System for Poly(Methyl Methacrylate)
8
AASHTO No. M237 Epoxy Resin Adhesive for Bonding
(PMMA) Molding and Extrusion Compounds
Traffic Markers to Hardened Concrete
D 1754 Test Method for Effect of Heat and Air on Asphaltic
AASHTO No. T237 Testing Epoxy Resin Adhesive
3. Terminology
1
This specification is under the jurisdiction of ASTM Committee D04 on Road
3.1 Definitions:
and Paving Materials and is the direct responsibility of Subcommittee D04.38 on
Highway Traffic Control Materials.
Current edition approved July 10, 2002. Published October 2002. Originally
9
published as D 4383 – 84. Last previous edition D 4383 – 01. Annual Book of ASTM Standards, Vol 05.02.
2 10
Annual Book of ASTM Standards, Vol 01.02. Discontinued; see 1995 Annual Book of ASTM Standards, Vol 04.03.
3 11
Discontinued; see 2001 Annual Book of ASTM Standards, Vol 04.01. Annual Book of ASTM Standards, Vol 08.02.
4 12
Annual Book of ASTM Standards, Vol 04.01. Annual Book of ASTM Standards, Vol 03.01.
5 13
Annual Book of ASTM Standards, Vol 04.03. Annual Book of ASTM Standards, Vol 06.01.
6 14
Annual Book of ASTM Standards, Vol 04.04. Available from U.S. Government Printing Office, Washington, DC 20402.
7 15
Annual Book of ASTM Standards, Vol 05.01. Available from American Association of State Highway and Transportation
8
Annual Book of ASTM Standards, Vol 08.01. Officials, 444 N. Capitol, Washington, DC 20001.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
D4383–02
3.1.1 coeffıc
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D8139-23(Specification)
Standard Specification for Semi-Rigid, Closed-Cell Polypropylene Foam, Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction

SCOPE
1.1 This specification covers preformed expansion joint fillers made from closed-cell polypropylene foam materials having suitable compressibility, recovery from compression, nonextruding, and weather-resistant characteristics.  
1.1.1 Type I, closed-cell polypropylene foam.  
1.2 These joint fillers are intended for use in concrete pavements in full-depth joints. There are several variations in size with typical thicknesses of 1/2 in. (12.7 mm), 3/4 in. (19.05 mm), and 1 in. (25.4 mm); typical widths of 31/2 in. (88.9 mm), 4 in. (101.6 mm), 5 in. (127 mm), 6 in. (152.5 mm), 7 in. (177.8 mm), 8 in. (203.2 mm), or 48 in. (1.2 m) sheet; and typical lengths of 5 ft (1.52 m) and 10 ft (3.05 m).  
1.3 The values stated in inch-pound units are to be regarded as the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D3319-23(Practice)
Standard Practice for the Accelerated Polishing of Aggregates Using the British Wheel

SIGNIFICANCE AND USE
4.1 This practice simulates the polishing action of vehicular traffic on coarse aggregates used in bituminous pavements.  
4.2 A polish value is determined that may be used to rate or classify coarse aggregates for their ability to resist polishing under traffic.
Note 1: The quality of the results produced by this standard are dependant upon the competence of the personnel performing the procedure and the capability, calibration, and the maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors: following the suggestions of Specification D3666 or similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This practice covers a laboratory procedure by which an estimate may be made of the extent to which different coarse aggregates may polish.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Regarding sieves, per Specification E11: “The values stated in SI units shall be considered standard for the dimensions of the wire cloth openings and the diameter of the wires used in the wire cloth.” When sieve mesh sizes are referenced, the alternate inch-pound designations are provided for information purposes and enclosed in parentheses.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D140/D140M-16(2023)(Practice)
Standard Practice for Sampling Asphalt Materials

SIGNIFICANCE AND USE
4.1 Sampling is as important as testing, and precautions shall be taken to obtain samples to show the true nature and condition of the materials.  
4.2 Samples are taken for either of the following two purposes:  
4.2.1 To represent as nearly as possible an average of the bulk of the materials sampled, or  
4.2.2 To ascertain the maximum variation in characteristics which the material possesses.
SCOPE
1.1 This practice applies to the sampling of asphalt materials at points of manufacture, storage, or delivery.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D517-23(Specification)
Standard Specification for Asphalt Plank

ABSTRACT
This specification covers asphalt plank used for bridge decks as well as for industrial floors. Asphalt planks shall be classified according to usage: Type Ia; Type Ib; and Type II. Asphalt plank shall be formed from a mixture of asphalt, fibers, modifiers, or a combination thereof, and mineral filler in such a manner as to produce a uniformly dense mass. The following test methods shall be intended to measure those attributes necessary to measure the ability of asphalt plank to provide a reasonably long and satisfactory service: absorption; brittleness; dimensions; and hardness.
SCOPE
1.1 This specification covers asphalt plank used for bridge decks as well as for industrial floors.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D8079-23(Practice)
Standard Practice for Preparation of Compacted Slab Asphalt Mix Samples Using a Segmented Rolling Compactor

SIGNIFICANCE AND USE
5.1 Asphalt slabs compacted with the rolling compactor can be used to obtain specimens for further testing, including bulk specific gravity following Test Methods D1188/D1188M, D2726/D2726M, and D6752/D6752M, fatigue performance characteristics following Test Methods D7460 and D8237 or AASHTO T 321, and Hamburg wheel-track testing following AASHTO T 324.  
5.2 Specimens to perform other standard tests could also be obtained, as long as their volume is contained within the volume of a slab.
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this practice are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline that provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This practice covers the fabrication of slabs of asphalt mix using an automated laboratory rolling compactor (RC). Compacted specimens are suitable for volumetric and physical property testing. This practice should not be used for acceptance or rejection of a material or for purchasing purposes.  
1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6628-23(Specification)
Standard Specification for Color of Retroreflective Pavement Marking Materials

ABSTRACT
This specification covers the daytime and nighttime color of retroreflective pavement marking materials, both painted and tape lines, including thermoplastic, epoxy and other types, used for traffic control lane markings and symbols on road surfaces. This specification is not applicable to the testing, for quality control purposes, of marking material without added drop-on beads. The performance requirements for which the marking materials shall be tested on and conform accordingly to are the daytime and nighttime chromaticity limits, retroreflectance, and daytime lightness limits (Y tristimulus coordinate).
SCOPE
1.1 This specification covers the daytime and nighttime color of retroreflective pavement marking materials used for traffic control lane markings and symbols on road surfaces.  
1.2 This specification applies to all retroreflective pavement markings (markings that include retroreflective optics residing on the surface) except structured pavement markings as defined in 3.2.5.  
1.3 This specification is not applicable to pavement markings that do not include retroreflective optics on the surface.  
1.4 This specification does not address any requirements other than the color of retroreflective pavement markings.  
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5.1 Exception—This specification is noted to be an SI document, where angles are generally expressed in radians. However, as angles used in retroreflection have historically been identified in degrees, the International Committee for Weights and Measures (CIPM, Comité International des Poids et Mesures) accepts the use of degrees with SI units, and European Normatives and documents from the International Commission on Illumination (CIE) use degrees for retroreflection geometry.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM D244-23(Test Method)
Standard Test Methods and Practices for Emulsified Asphalts

SIGNIFICANCE AND USE
5.1 This test method measures the amount of water present in the emulsified asphalt, as distinguished from either bitumen or petroleum solvent.
SCOPE
1.1 These test methods and practices, given under the headings titled Composition, Consistency, Stability, and Examination of Residue, cover the examination of asphalt emulsions composed principally of a semisolid or liquid asphaltic base, water, and an emulsifying agent. The test methods cover the following tests and practices:    
Test  
Sections  
Composition:  
Water Content  
4 – 10  
Residue and Oil Distillate by Distillation  
See Test Method
D6997  
Residue by Evaporation  
See Test Method
D6934  
Particle Charge of Cationic Emulsified Asphalts  
See Practice
D7402  
Consistency:  
Viscosity (Saybolt Furol)  
See Test Method
D7496  
Stability:  
Demulsibility  
See Test Method
D6936  
Settlement  
See Test Method
D6930  
Cement Mixing  
See Test Method
D6935  
Sieve Test  
See Test Method
D6933  
Aggregate Coating  
See Practice
D6998  
Miscibility with Water  
See Practice
D6999  
Freezing  
See Practice
D6929  
Coating Ability and Water Resistance  
11 – 18  
Storage Stability of Asphalt Emulsion  
See Test Method
D6930  
Examination of Residue  
19 – 26  
Identification Test for Rapid Setting Cationic Emulsified Asphalt  
27 – 34  
Identification of Cationic Slow Set Emulsions  
See Practice
D7402  
Field Coating Test on Emulsified Asphalts  
35 – 40  
Emulsified Asphalt/Job Aggregate Coating Test  
41 – 46  
Density of Emulsified Asphalt  
See Test Method
D6937  
Residue by Low-Temperature Vacuum Distillation  
See Test Method
D7403  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM D6373-23(Specification)
Standard Specification for Performance-Graded Asphalt Binder

ABSTRACT
This specification covers asphalt binders graded by performance. Grading designations are related to the average seven-day maximum pavement design temperature, and minimum pavement design temperature. Asphalt binder shall be prepared by the refining of crude petroleum by suitable methods, with or without the addition of modifiers, which may be any organic material of suitable manufacture that is used in virgin or recycled condition, and that is dissolved, dispersed or reacted in asphalt cement to enhance its performance. This specification incorporates an aid for determining the critical low cracking temperature using a combination of test procedures.
SCOPE
1.1 This specification2 covers asphalt binders graded by performance. Grading designations are related to the LTPPBind Online calculated maximum pavement design temperature and the minimum pavement design temperature. This specification contains Tables 1 and 2. Table 2 incorporates Practice D6816 for determining the critical low cracking temperature using a combination of Test Method D6648 and Test Method D6723 test procedures. If no table is specified, the default is Table 1.
Note 1: For more information on LTPPBind Online, see https://infopave.fhwa.dot.gov/Tools/LTPPBindOnline accessed May 23, 2023.
Note 2: For asphalt cements graded by penetration at 25 °C, see Specification D946/D946M. For asphalt cements graded by viscosity at 60 °C, see Specification D3381/D3381M.
Note 3: AASHTO R 29 provides non-mandatory information for determining the performance grade of an asphalt binder.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM D3633/D3633M-23(Test Method)
Standard Test Method for Electrical Resistivity of Membrane-Pavement Systems

SIGNIFICANCE AND USE
4.1 This test method for measuring the electrical resistivity of water-barrier membrane-pavement systems may be interpreted to indicate the effectiveness of such systems.  
4.2 This test method is predicated on the fact that an electrical connection between the surface of the pavement and the reinforcing steel in the concrete pavement cannot be made through an impermeable water-barrier membrane.  
4.3 This test method may be used for acceptance when the accepting agency specifies the minimum resistance value desired.  
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers the measurement of the electrical resistivity of water-barrier membrane-pavement systems when applied to concrete bridge decks.  
1.2 Measurements shall be performed on the bituminous pavement surface covering the water-barrier membrane.  
1.3 This test method utilizes a measure of electrical resistance between the saturated top surface of the water-barrier membrane and the reinforcing steel embedded in the concrete bridge deck.  
1.4 The values measured represent the electrical resistance obtained with the equipment and procedures stated herein and do not necessarily agree or correlate with those using other equipment or procedures.  
1.5 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.6 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D8239-23(Specification)
Standard Specification for Performance-Graded Asphalt Binder Using the Multiple Stress Creep and Recovery (MSCR) Test

SCOPE
1.1 This specification2 covers asphalt binders graded by performance. Grading designations are related to the LTPPBind Online calculated maximum pavement design temperature, the minimum pavement design temperature, and the traffic loading.
Note 1: For more information on LTPPBind Online, see https://infopave.fhwa.dot.gov/Tools/LTPPBindOnline accessed May 23, 2023.  
1.2 This specification incorporates Test Method D7405 for determining non-recoverable creep compliance, Jnr. “S,” “H,” “V,” or “E” designations must be specified for standard, heavy, very heavy, and extremely heavy traffic loading, respectively.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
Note 2: A guidance document for specifying bodies using R % for elastic properties is under development.
Note 3: For asphalt binders graded by penetration at 25 °C, see Specification D946/D946M. For asphalt binders graded by viscosity at 60 °C, see Specification D3381/D3381M. For performance-graded asphalt binder, see Specification D6373.
Note 4: AASHTO R 29 provides non-mandatory information for determining the performance grade of an asphalt binder.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off