iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D6373-23

(Specification)

Standard Specification for Performance-Graded Asphalt Binder

Standard Specification for Performance-Graded Asphalt Binder

ABSTRACT
This specification covers asphalt binders graded by performance. Grading designations are related to the average seven-day maximum pavement design temperature, and minimum pavement design temperature. Asphalt binder shall be prepared by the refining of crude petroleum by suitable methods, with or without the addition of modifiers, which may be any organic material of suitable manufacture that is used in virgin or recycled condition, and that is dissolved, dispersed or reacted in asphalt cement to enhance its performance. This specification incorporates an aid for determining the critical low cracking temperature using a combination of test procedures.
SCOPE
1.1 This specification2 covers asphalt binders graded by performance. Grading designations are related to the LTPPBind Online calculated maximum pavement design temperature and the minimum pavement design temperature. This specification contains Tables 1 and 2. Table 2 incorporates Practice D6816 for determining the critical low cracking temperature using a combination of Test Method D6648 and Test Method D6723 test procedures. If no table is specified, the default is Table 1.
Note 1: For more information on LTPPBind Online, see https://infopave.fhwa.dot.gov/Tools/LTPPBindOnline accessed May 23, 2023.
Note 2: For asphalt cements graded by penetration at 25 °C, see Specification D946/D946M. For asphalt cements graded by viscosity at 60 °C, see Specification D3381/D3381M.
Note 3: AASHTO R 29 provides non-mandatory information for determining the performance grade of an asphalt binder.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
30-Jun-2023
ICS
93.080.20 - Road construction materials
Technical Committee
D04 - Road and Paving Materials
Drafting Committee
D04.40 - Asphalt Specifications
Current Stage
Ref Project

Relations

Refers
ASTM D946/D946M-20 - Standard Specification for Penetration-Graded Asphalt Binder for Use in Pavement Construction
Effective Date
01-May-2020

Buy Standard

ASTM D6373-23 - Standard Specification for Performance-Graded Asphalt BinderASTM D6373-23 - Standard Specification for Performance-Graded Asphalt Binder
PreviousNext
Technical specification
ASTM D6373-23 - Standard Specification for Performance-Graded Asphalt Binder
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM D6373-23 - Standard Specification for Performance-Graded Asphalt BinderREDLINE ASTM D6373-23 - Standard Specification for Performance-Graded Asphalt Binder
PreviousNext
Technical specification
REDLINE ASTM D6373-23 - Standard Specification for Performance-Graded Asphalt Binder
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D6373 − 23
Standard Specification for
1
Performance-Graded Asphalt Binder
This standard is issued under the fixed designation D6373; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D95 Test Method for Water in Petroleum Products and
2
Bituminous Materials by Distillation
1.1 This specification covers asphalt binders graded by
D140/D140M Practice for Sampling Asphalt Materials
performance. Grading designations are related to the LTPP-
D946/D946M Specification for Penetration-Graded Asphalt
Bind Online calculated maximum pavement design tempera-
Binder for Use in Pavement Construction
ture and the minimum pavement design temperature. This
D2042 Test Method for Solubility of Asphalt Materials in
specification contains Tables 1 and 2. Table 2 incorporates
Trichloroethylene or Toluene
Practice D6816 for determining the critical low cracking
D2872 Test Method for Effect of Heat and Air on a Moving
temperature using a combination of Test Method D6648 and
Film of Asphalt Binder (Rolling Thin-Film Oven Test)
Test Method D6723 test procedures. If no table is specified, the
D3381/D3381M Specification for Viscosity-Graded Asphalt
default is Table 1.
Binder for Use in Pavement Construction
NOTE 1—For more information on LTPPBind Online, see https://
D4402/D4402M Test Method for Viscosity Determination of
infopave.fhwa.dot.gov/Tools/LTPPBindOnline accessed May 23, 2023.
Asphalt at Elevated Temperatures Using a Rotational
NOTE 2—For asphalt cements graded by penetration at 25 °C, see
Viscometer
Specification D946/D946M. For asphalt cements graded by viscosity at
D6521 Practice for Accelerated Aging of Asphalt Binder
60 °C, see Specification D3381/D3381M.
NOTE 3—AASHTO R 29 provides non-mandatory information for
Using a Pressurized Aging Vessel (PAV)
determining the performance grade of an asphalt binder.
D6648 Test Method for Determining the Flexural Creep
1.2 The values stated in SI units are to be regarded as Stiffness of Asphalt Binder Using the Bending Beam
standard. No other units of measurement are included in this Rheometer (BBR)
standard. D6723 Test Method for Determining the Fracture Properties
of Asphalt Binder in Direct Tension (DT) (Withdrawn
1.3 This international standard was developed in accor-
4
2021)
dance with internationally recognized principles on standard-
D6816 Practice for Determining Low-Temperature Perfor-
ization established in the Decision on Principles for the
4
mance Grade (PG) of Asphalt Binders (Withdrawn 2021)
Development of International Standards, Guides and Recom-
D7175 Test Method for Determining the Rheological Prop-
mendations issued by the World Trade Organization Technical
erties of Asphalt Binder Using a Dynamic Shear Rheom-
Barriers to Trade (TBT) Committee.
eter
D7553 Test Method for Solubility of Asphalt Materials in
2. Referenced Documents
N-Propyl Bromide
3
2.1 ASTM Standards:
5
2.2 AASHTO Standards:
D8 Terminology Relating to Materials for Roads and Pave-
AASHTO R 29 Grading or Verifying the Performance Grade
ments
of an Asphalt Binder
D92 Test Method for Flash and Fire Points by Cleveland
AASHTO M 320 Standard Specification for Performance-
Open Cup Tester
Graded Asphalt Binder
3. Terminology
1
This specification is under the jurisdiction of ASTM Committee D04 on Road
3.1 Definitions:
and Paving Materials and is the direct responsibility of Subcommittee D04.40 on
3.1.1 Definitions for many terms common to asphalt binder
Asphalt Specifications.
Current edition approved July 1, 2023. Published July 2023. Originally approved
are found in Terminology D8.
in 1999. Last previous edition approved in 2021 as D6373 – 21a. DOI: 10.1520/
D6373-23.
2 4
This specification is based on SHRP Product 1001 and AASHTO MP1. The last approved version of this historical standard is referenced on
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or www.astm.org.
5
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from American Association of State Highway and Transportation
Standards volume information, refer to the standard’s Document Summary page on Officials (AASHTO), 444 N. Capitol St., NW, Suite 249, Washington, DC 20001,
the ASTM website. http://www.transportation.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D6373 − 23
suitability
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D6373 − 21a D6373 − 23
Standard Specification for
1
Performance-Graded Asphalt Binder
This standard is issued under the fixed designation D6373; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
2
1.1 This specification covers asphalt binders graded by performance. Grading designations are related to the LTPPBind Online
calculated maximum pavement design temperature and the minimum pavement design temperature. This specification contains
Tables 1 and 2. Table 2 incorporates Practice D6816 for determining the critical low cracking temperature using a combination of
Test Method D6648 and Test Method D6723 test procedures. If no table is specified, the default is Table 1.
NOTE 1—For more information on LTPPBind online,Online, see https://infopave.fhwa.dot.gov/Tools/LTPPBindOnline accessed May 23, 2023June 10,
2020.
NOTE 2—For asphalt cements graded by penetration at 25 °C, see Specification D946/D946M. For asphalt cements graded by viscosity at 60 °C, see
Specification D3381/D3381M.
NOTE 3—AASHTO R 29 provides non-mandatory information for determining the performance grade of an asphalt binder.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
3
2.1 ASTM Standards:
D8 Terminology Relating to Materials for Roads and Pavements
D92 Test Method for Flash and Fire Points by Cleveland Open Cup Tester
D95 Test Method for Water in Petroleum Products and Bituminous Materials by Distillation
D140/D140M Practice for Sampling Asphalt Materials
D946/D946M Specification for Penetration-Graded Asphalt Binder for Use in Pavement Construction
D2042 Test Method for Solubility of Asphalt Materials in Trichloroethylene or Toluene
D2872 Test Method for Effect of Heat and Air on a Moving Film of Asphalt Binder (Rolling Thin-Film Oven Test)
D3381/D3381M Specification for Viscosity-Graded Asphalt Binder for Use in Pavement Construction
D4402/D4402M Test Method for Viscosity Determination of Asphalt at Elevated Temperatures Using a Rotational Viscometer
D6521 Practice for Accelerated Aging of Asphalt Binder Using a Pressurized Aging Vessel (PAV)
1
This specification is under the jurisdiction of ASTM Committee D04 on Road and Paving Materials and is the direct responsibility of Subcommittee D04.40 on Asphalt
Specifications.
Current edition approved June 15, 2021July 1, 2023. Published July 2021July 2023. Originally approved in 1999. Last previous edition approved in 2021 as
D6373 – 21.D6373 – 21a. DOI: 10.1520/D6373-21A.10.1520/D6373-23.
2
This specification is based on SHRP Product 1001 and AASHTO MP1.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D6373 − 23
D6648 Test Method for Determining the Flexural Creep Stiffness of Asphalt Binder Using the Bending Beam Rheometer (BBR)
4
D6723 Test Method for Determining the Fracture Properties of Asphalt Binder in Direct Tension (DT) (Withdrawn 2021)
4
D6816 Practice for Determining Low-Temperature Performance Grade (PG) of Asphalt Binders (Withdrawn 2021)
D7175 Test Method for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer
D7553 Test Method for Solubility of Asphalt Materials in N-Propyl Bromide
5
2.2 AASHTO Standards:
AASHTO R 29 Grading or Verifying the Performance Grade of an Asphalt Binder
AASHTO M 320 Standard Specification for Performance-Graded Asphalt Binder
3. Terminology
3.1 Definitions:
3.1.1 Definitions for many terms common to asphalt binder are found in Terminology D8.
4. Ordering Information
4.1 When ordering under this specification, include in the purchase order
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D3633/D3633M-23(Test Method)
Standard Test Method for Electrical Resistivity of Membrane-Pavement Systems

SIGNIFICANCE AND USE
4.1 This test method for measuring the electrical resistivity of water-barrier membrane-pavement systems may be interpreted to indicate the effectiveness of such systems.  
4.2 This test method is predicated on the fact that an electrical connection between the surface of the pavement and the reinforcing steel in the concrete pavement cannot be made through an impermeable water-barrier membrane.  
4.3 This test method may be used for acceptance when the accepting agency specifies the minimum resistance value desired.  
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers the measurement of the electrical resistivity of water-barrier membrane-pavement systems when applied to concrete bridge decks.  
1.2 Measurements shall be performed on the bituminous pavement surface covering the water-barrier membrane.  
1.3 This test method utilizes a measure of electrical resistance between the saturated top surface of the water-barrier membrane and the reinforcing steel embedded in the concrete bridge deck.  
1.4 The values measured represent the electrical resistance obtained with the equipment and procedures stated herein and do not necessarily agree or correlate with those using other equipment or procedures.  
1.5 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.6 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D8239-23(Specification)
Standard Specification for Performance-Graded Asphalt Binder Using the Multiple Stress Creep and Recovery (MSCR) Test

SCOPE
1.1 This specification2 covers asphalt binders graded by performance. Grading designations are related to the LTPPBind Online calculated maximum pavement design temperature, the minimum pavement design temperature, and the traffic loading.
Note 1: For more information on LTPPBind Online, see https://infopave.fhwa.dot.gov/Tools/LTPPBindOnline accessed May 23, 2023.  
1.2 This specification incorporates Test Method D7405 for determining non-recoverable creep compliance, Jnr. “S,” “H,” “V,” or “E” designations must be specified for standard, heavy, very heavy, and extremely heavy traffic loading, respectively.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
Note 2: A guidance document for specifying bodies using R % for elastic properties is under development.
Note 3: For asphalt binders graded by penetration at 25 °C, see Specification D946/D946M. For asphalt binders graded by viscosity at 60 °C, see Specification D3381/D3381M. For performance-graded asphalt binder, see Specification D6373.
Note 4: AASHTO R 29 provides non-mandatory information for determining the performance grade of an asphalt binder.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM D8125-18(2023)(Specification)
Standard Specification for Re-Refined Engine Oil Bottoms (REOB)/Vacuum Tower Asphalt Extender (VTAE)

ABSTRACT
This specification establishes the material, manufacturing, and physical requirements for re-refined engine oil bottoms, also known as vacuum tower asphalt extender, that may be used in formulating asphalt for pavement construction and roofing. "Re-refined engine oil bottoms" (REOB) is the commonly used term used by many state highway agencies and FHWA, while "vacuum tower asphalt extender" (VTAE) is preferred by manufacturers. REOB/VTAE may be obtained by processing used engine oil using atmospheric distillation followed by vacuum distillation to produce a vacuum residuum meeting the requirements outlined in this specification. The REOB/VTAE shall be homogenous, free from water, and not foam when heated to 232°C (450°F).
SCOPE
1.1 This specification covers re-refined engine oil bottoms, also known as vacuum tower asphalt extender, that may be used in formulating asphalt for pavement construction and roofing. This specification has been developed specifically for these two categories of product and is not intended for other uses. Table 1 is to be used for pavement construction and Table 2 for roofing. “Re-refined engine oil bottoms” (REOB) is the prevailing name used by many state highway agencies and FHWA, while “vacuum tower asphalt extender” (VTAE) is the preferred name used by the manufacturers of the product. Since each name provides an important descriptor of production elements (“re-refined” and “vacuum tower”) for the specific product this specification addresses, this specification uses the term “REOB/VTAE.”  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D7196-23(Test Method)
Standard Test Method for Raveling Test of Cold-Mixed Emulsified Asphalt Samples

SIGNIFICANCE AND USE
4.1 This test is useful for classifying the curing and formulation of cold-mixed emulsified asphalt samples through ravel testing of compacted specimens. This performance test should be used to rank the mix conditions and approximate curing time for return to traffic and resistance to weather damage.
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method measures the resistance to raveling characteristics of emulsified asphalt and field aggregates or recycled asphalt pavement (RAP) mixtures by simulating an abrasion similar to early return to traffic.  
1.2 A precision and bias statement for this standard has not been developed at this time. Therefore, this standard should not be used for acceptance or rejection of a material for purchasing purposes.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D8044-23(Test Method)
Standard Test Method for Evaluation of Asphalt Mixture Cracking Resistance Using the Semi-Circular Bend Test (SCB) at Intermediate Temperatures

SIGNIFICANCE AND USE
5.1 The critical strain energy release rate parameter, Jc, is used to compare the cracking resistance of asphalt mixtures prepared with different asphalt binder and aggregate types prepared to meet the volumetric requirements of differing traffic levels tested at intermediate temperatures.  
5.2 The critical strain energy release rate parameter, Jc, is an engineering property and a performance indicator at intermediate temperature cracking.
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers the procedures for preparation, testing, and measurement of asphalt mixture cracking resistance at intermediate temperatures using semi-circular bend (SCB) geometry of laboratory-prepared or pavement core asphalt mixture samples tested monotonically. The SCB sample is a half-disk with a notch cut aligned vertically in parallel with the testing loading. The test method describes the determination of the critical strain energy release rate parameter, Jc, and other parameters determined from the load-displacement curve. These parameters can be used to rank the resistance of asphalt mixtures to cracking.  
1.2 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 Since a complete Precision and Bias statement for this standard has not been developed, the test method is to be used for research and informational purposes only. Therefore, this standard should not be used for acceptance or rejection of a material for purchasing purposes.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D6372-23(Practice)
Standard Practice for Design, Testing, and Construction of Microsurfacing

SIGNIFICANCE AND USE
5.1 This microsurfacing practice is written as a guide and should not be construed as a specification. End use specifications should be adapted to conform to job and user requirements.
Note 2: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This practice covers the design, testing, and construction of mixtures of polymer-modified asphalt emulsion, mineral aggregate, mineral filler, water, and other additives, properly proportioned, mixed and spread on a paved surface. It is written as a guide and should be used as such. End use specifications should be adapted to conform to job and user requirements.
Note 1: This practice references test methods outside the jurisdiction of ASTM that may or may not have a precision statement.  
1.2 The values stated in SI units are to be regarded as the standard.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D3549/D3549M-18(2023)(Test Method)
Standard Test Method for Thickness or Height of Compacted Asphalt Mixture Specimens

SIGNIFICANCE AND USE
4.1 The thickness of a compacted asphalt mixture is often used as a construction check to ensure that the proper quantity of materials has been placed on a project, and to correct strength measurement on constant diameter specimens with varying heights.
Note 1: The text of this test method references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the test method.
Note 2: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers determination of the thickness (or height) of compacted asphalt mixture specimens.  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.2.1 Section 7.4 specifies SI units because they are the units used in the equations for Test Methods D1188/D1188M and D2726/D2726M. Performing calculations without first converting any measurements made in inch-pound units to SI units in 7.4 will result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D8188-23(Test Method)
Standard Test Method for Determination of Density and Relative Density of Asphalt, Semi-Solid Bituminous Materials, and Soft-Tar Pitch by Use of a Digital Density Meter (U-Tube)

SIGNIFICANCE AND USE
5.1 Values of density are used for converting volumes to units of mass and for correcting measured volumes at the measured temperature to a standard temperature using Practice D4311/D4311M.
Note 2: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers the determination of the relative density and density of semi-solid asphalt materials, asphalt binders, asphalt cements, and soft-tar pitches by use of a digital density meter (U-tube).
Note 1: Alternate methods for determining the density of semi-solid and solid asphalt materials and asphalt binders include Test Methods D3289, D3142/D3142M, and D70/D70M.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. No other units of measurement are included in this standard, with the exception of temperature measurements. Units provided in degrees Fahrenheit are for reference purposes only. Temperatures given in degrees Celsius are to be considered standard.  
1.3 This test method should not be applied to petroleum distillates other than asphalt and asphalt binders. For the determination of density of all other petroleum distillates and viscous oils, use Test Method D4052 or D5002, or ISO 12185.  
1.4 The text of this standard references notes and footnotes which provide explanatory material. These footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6153-23(Specification)
Standard Specification for Materials for Bridge Deck Waterproofing Membrane Systems

ABSTRACT
This specification covers three types of deck waterproofing membrane systems designed for use on bridge decks which will receive an asphaltic concrete overlay. Type I are cold liquid-applied chemically curing membrane materials that that require a membrane protection course. Type II, on the other hand, are hot applied elastomeric membrane systems that also require a membrane protection course. And finally, Type III are preformed sheet membrane systems. All types are applied to a bridge deck to prevent the passage of water from the bituminous surface course to or through the bridge deck. Membrane systems shall be sampled as appropriate for each type, and shall conform to performance requirements and physical properties as to permeability, and pliability.
SCOPE
1.1 This specification covers deck waterproofing membrane systems designed for use on bridge decks which will receive an asphaltic concrete overlay.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D8140-18(2023)(Guide)
Standard Guide for the Use of Foundry Sand in Asphalt Mixtures

SCOPE
1.1 This guide covers the physical and chemical requirements of virgin or recovered foundry sand for use as a fine aggregate in asphalt mixtures.  
1.2 This guide is for use by contractors, foundry sand suppliers, or other purchasers as part of the purchase document describing the material to be furnished. Those responsible for selecting the proportions for the asphalt mixture should have the responsibility of determining the proportions of foundry sand as a fine aggregate.  
1.3 The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.  
1.4 The text of this standard references notes and footnotes which provide explanatory information. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off