iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F853-05

(Practice)

Standard Practice for Maintenance Procedures for Amusement Rides and Devices (Withdrawn 2014)

Standard Practice for Maintenance Procedures for Amusement Rides and Devices (Withdrawn 2014)

SIGNIFICANCE AND USE
The purpose of this practice is to delineate information for the maintenance of amusement rides and devices.
SCOPE
1.1 This practice establishes information for maintenance procedures of amusement rides and devices.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This practice establishes information for maintenance procedures of amusement rides and devices.
Formerly under the jurisdiction of Committee F24 on Amusement Rides and Devices, this practice was withdrawn in July 2014 in accordance with section 10.6.3 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.

General Information

Status
Withdrawn
Publication Date
14-Aug-2005
Withdrawal Date
16-Jul-2014
ICS
97.200.99 - Other equipment for entertainment
Technical Committee
F24 - Amusement Rides and Devices
Drafting Committee
F24.30 - Auditing
Current Stage
Ref Project

Relations

Replaces
ASTM F853-04 - Standard Practice for Maintenance Procedures for Amusement Rides and Devices
Effective Date
15-Aug-2005
Referred By
ASTM F1487-21 - Standard Consumer Safety Performance Specification for Playground Equipment for Public Use
Effective Date
15-Aug-2005
Referred By
ASTM F3101-21a - Standard Specification for Unsupervised Public Use Outdoor Fitness Equipment
Effective Date
15-Aug-2005
Referred By
ASTM F2375-09(2017) - Standard Practice for Design, Manufacture, Installation and Testing of Climbing Nets and Netting/Mesh used in Amusement Rides, Devices, Play Areas and Attractions
Effective Date
15-Aug-2005

Buy Standard

ASTM F853-05 - Standard Practice for Maintenance Procedures for Amusement Rides and Devices (Withdrawn 2014)ASTM F853-05 - Standard Practice for Maintenance Procedures for Amusement Rides and Devices (Withdrawn 2014)
PreviousNext
Standard
ASTM F853-05 - Standard Practice for Maintenance Procedures for Amusement Rides and Devices (Withdrawn 2014)
English language
8 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F853 − 05
StandardPractice for
Maintenance Procedures for Amusement Rides and
1
Devices
ThisstandardisissuedunderthefixeddesignationF853;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 4.1.1 Description of the ride or device operation, including
the function and operation of its major components.
1.1 This practice establishes information for maintenance
4.1.1.1 Description of the designed motion(s) of the ride or
procedures of amusement rides and devices.
device during operation.
1.2 This standard does not purport to address all of the
4.1.2 Description of the recommended procedures for
safety concerns, if any, associated with its use. It is the
installation, setup, disassembly, and transportation of an
responsibility of the user of this standard to establish appro-
amusement ride or device, where applicable.
priate safety and health practices and determine the applica-
4.1.3 Recommended lubrication procedures for the amuse-
bility of regulatory limitations prior to use.
ment ride or device.
4.1.3.1 Recommended types and specifications of lubri-
2. Referenced Documents
cants.
2
2.1 ASTM Standards:
4.1.3.2 Recommendedfrequency,andifapplicable,quantity
F846 Guide for Testing Performance of Amusement Rides
of lubrication.
and Devices
4.1.3.3 Alubrication drawing, chart, or instruction, showing
F893 Guide for Auditing Amusement Rides and Devices
the location of lubrication points.
F1159 Practice for Design and Manufacture of Patron
4.1.3.4 Recommended application method of lubrication.
Directed, Artificial Climbing Walls, Dry Slide, Coin
Operated and Purposeful Water Immersion Amusement 4.1.4 Description of the recommended daily, preopening
inspections to be performed.
Rides and Devices and Air-Supported Structures
F1193 Practice for Quality, Manufacture, and Construction
4.1.5 Description, including frequency, of recommended
of Amusement Rides and Devices
maintenance inspections and testing, other than daily preopen-
F2291 Practice for Design ofAmusement Rides and Devices
ing inspection.
4.1.5.1 Recommended wear limits or tolerances, where
3. Significance and Use
deemed necessary by the manufacturer.
4.1.5.2 Recommended operational testing as specified in
3.1 The purpose of this practice is to delineate information
for the maintenance of amusement rides and devices. Guide F846.
4.1.5.3 Where applicable, recommended nondestructive
4. Manufacturer’s Responsibility
testing (NDT) as specified in Guide F846.
4.1.5.4 Tests recommended pursuant to 4.1.5 shall meet the
4.1 The manufacturer of an amusement ride or device shall
following criteria:
provide, with delivery of each ride or device, documented
maintenance instructions in the English language. These in- (1) The tests shall have been performed satisfactorily by the
manufacturer prior to the sale of the amusement ride or device,
structions shall include, but not be limited to, the following:
(2) The test shall be a test which the amusement ride or
device, or element, can reasonably be expected to pass during
1 the expected life of the amusement ride or device, or element,
This practice is under the jurisdiction ofASTM Committee F24 on Amusement
Rides and Devices and is the direct responsibility of Subcommittee F24.30 on
assuming recommended maintenance and operating proce-
Maintenance and Inspection.
dures have been followed,
Current edition approved Aug. 15, 2005. Published September 2005. Originally
(3) The test shall be a test that is reasonable, and which the
approved in 1983. Last previous edition approved in 2004 as F853 – 04. DOI:
10.1520/F0853-05. owner/operator can reasonably be expected to be competent to
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
perform or cause to be performed.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
4.1.6 Recommended specifications for the use of replace-
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. ment fasteners, and recommended torque requirements for
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F853 − 05
fasteners, where applicable. If appropriate, precautionary in- (8) The serial numbers of the affected rides or devices,
formation will be provided relating to the continued use of (9) The applicable dates of manufacture for the affected
fasteners that have been loosened or retorqued. rides or devices,
4.1.7 Schematics of electrical power, lighting, controls, and (10) A num
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F747-23(Terminology)
Standard Terminology Relating to Amusement Rides and Devices

SCOPE
1.1 This terminology is a repository of terms approved by Committee F24 and its subcommittees. Reproducing terms approved within all other individual F24 standards and guides, this terminology will provide a single location where terms related to amusement rides and devices are freely accessible to the public, committee members and can be maintained, updated and utilized as effective communication tools. Although published alphabetically, terms unique to a specific F24 standard or guide are indicated as such by the reference which follows the applicable term.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM F3054-23(Practice)
Standard Practice for Operations of Amusement Railway Rides, Devices, and Facilities

SIGNIFICANCE AND USE
4.1 The purpose of this practice is to delineate information and to establish procedures for the operation of an amusement railway ride.  
4.2 The user of this standard shall be required to review and comply with the referenced “core” ASTM Committee F24 standards in Subsection 2.1 of this standard. Modified or alternate requirements to those standards may be required in this standard.
SCOPE
1.1 This practice applies to operations of amusement railway ride(s) that have a track gauge greater than or equal to 12 in. (305 mm) measured between the heads of the rails. This excludes patron powered ride vehicles specifically designed for children.  
1.2 This standard does not apply to the operation of rides, such as roller coasters, that resemble railways, but fall within the scope of Practice F2291-22a or Practice F1159-16ε1. This standard also does not apply to funiculars as defined in ANSI B77.2-20 or BS EN 1907-17.  
1.3 This standard does not apply to amusement railway rides operation that are intended for use as a portable amusement ride or attraction.  
1.4 This standard does not apply to permanently installed amusement railway rides and tourist railways, and their associated track, devices and facilities that are under the jurisdiction of the Federal Railroad Administration (FRA) in whole or part or national equivalent.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM F770-23(Practice)
Standard Practice for Ownership, Operation, Maintenance, and Inspection of Amusement Rides and Devices

SIGNIFICANCE AND USE
4.1 The purpose of this practice is to delineate information and to establish procedures for the operation, maintenance, inspection, and training for amusement rides and devices.
SCOPE
1.1 This practice provides guidelines for operations, maintenance, and inspection procedures for amusement rides and devices to be performed by the owner/operator.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM F2960-23(Practice)
Standard Practice for Permanent Amusement Railway Ride Tracks and Related Devices

SIGNIFICANCE AND USE
4.1 The user of this standard shall be required to review and comply with the referenced “core” ASTM F24 Committee standards in 2.1 of this standard. Modified or alternate requirements to those standards may be required in this standard.  
4.1.1 Amusement railway sub-systems may be built to various scales, that is, rolling stock maybe to one scale and the track to another but have common gauge. The railroad’s documentation or maintenance manuals shall identify the railroad standards of the respective subsystems/interfaces.  
4.1.2 The Designer/Engineer’s requirements shall consider the track equipment manufacturer’s and rolling stock manufacturer’s requirements and shall determine their appropriate interfaces.
SCOPE
1.1 This standard applies to design, manufacture, installation, operation, maintenance, and inspection of permanent amusement railway ride(s) that have a track gauge greater than or equal to 12 in. (305 mm) measured between the heads of the rails and their related devices and facilities, for example, bridges, tunnels, and signal support structures, excluding rolling stock. This “track” specific standard provides requirements which are not covered in the “core” or “supporting” standards of the ASTM F24 committee.  
1.2 This standard does not apply to track rides, such as roller coasters, that may resemble railways.  
1.3 This standard does not apply to funiculars as defined in ANSI B77.2 (2020) or BS EN 1907 (2017).  
1.4 This standard does not apply to Amusement Railway Rides and their associated track, devices and facilities that are manufactured and intended for use as a portable amusement ride or attraction.  
1.5 This standard does not apply to permanently installed amusement railway rides and tourist railways, and their associated track, devices and facilities that are under the jurisdiction of the United States Federal Railroad Administration (FRA) in whole or part, or national equivalent.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    40 pages
    English language
    sale 15% off
  • Standard
    40 pages
    English language
    sale 15% off
ASTM
ASTM F1193-23(Practice)
Standard Practice for Quality, Manufacture, and Construction of Amusement Rides and Devices

SIGNIFICANCE AND USE
3.1 The purpose of this practice is to provide the minimum manufacturing requirements for amusement rides and devices and to provide the minimum requirements for a written quality assurance program for an amusement ride or device manufacturer, or component supplier. This is not intended to include suppliers of off-the-shelf components (for example, fasteners, electrical wire).
SCOPE
1.1 This practice establishes the minimum requirements for a quality assurance program and the manufacturing of amusement rides and devices (including major modifications).  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    12 pages
    English language
    sale 15% off
  • Standard
    12 pages
    English language
    sale 15% off
ASTM
ASTM F3214-23(Practice)
Standard Practice for Characterization of Fire Properties of Seating, Upholstery, and Padding Materials for Vehicles Associated with Amusement Rides and Devices

SIGNIFICANCE AND USE
4.1 This practice requires that seating, upholstery, and padding materials used for vehicles associated with amusement rides and devices exhibit adequate smoldering ignition properties.  
4.1.1 Noncombustible materials are permitted to be used as seating, upholstery, and padding materials, and do not require testing for smoldering ignition.  
4.2 The structural components or framing associated with a vehicle or ride are not considered seating, upholstery, or padding materials.  
4.3 Annex A1 provides an optional open flame test suitable for seat padding materials.  
4.4 Appendix X1 provides non-mandatory guidance for conducting an analysis of fire scenarios associated with the operation of vehicles associated with amusement rides and devices. The conduction of a fire hazard analysis is not a requirement of this practice. The purpose of Appendix X1 is to provide manufacturers, owners, and operators with criteria and references for fire properties of materials used in vehicles either following construction or major modifications of an amusement ride or device.  
4.5 This practice does not address the probability of occurrence of a hazardous event in any fire scenario associated with amusement rides or devices. Thus, this practice does not address the potential risk associated with any fire scenario. Practice F2291-21 includes general requirement to assess and mitigate hazards for all rides and devices.  
4.6 The requirements in this practice are not intended to supersede any additional or alternate requirements provided by the authority having jurisdiction.
SCOPE
1.1 This practice describes the required smoldering ignition fire properties for seating, upholstery, and padding materials used for vehicles associated with amusement rides and devices.  
1.2 This practice includes an annex with an example of an optional open flame test method for padding materials.  
1.3 This practice also contains a non-mandatory appendix with optional guidance for the procedure to follow in the event that an optional fire hazard analysis is to be conducted for vehicles used on amusement rides and devices.  
1.3.1 In the event that such a fire hazard analysis is to be conducted, it needs to include considerations related to heat release, smoldering, and flaming ignition, flame spread and smoke release.  
1.3.2 The appendix contains specific recommendations of standardized fire test methods that are suitable (but not required) for determining material properties related to heat release rates, smoldering, and flaming ignition, flammability, and smoke release for materials.  
1.4 This practice is not a fire test method.  
1.5 This practice does not require the conduction of a fire hazard analysis.  
1.6 This practice does not address the use of active fire protection measures, such as fire sprinklers, or smoke, fire, or heat detectors.  
1.7 This practice does not address the probability of any fire scenario associated with amusement rides or devices resulting in a hazardous event. Thus, this practice does not address the potential risk associated with any fire scenario. Practice F2291-21 includes general requirement to assess and mitigate hazards for all rides and devices.  
1.8 This practice shall not apply to:  
1.8.1 Materials specified for amusement rides or devices other than those associated specifically with the ride vehicle assembly.  
1.8.2 Materials used for the construction of facilities.  
1.8.3 Fluids and lubricants.  
1.8.4 Vehicles used on water slides or other aquatic devices.  
1.9 The values stated in SI units, see IEEE/ASTM SI-10-16, are to be regarded as standard. The values given in parentheses, if any, after SI units are provided for information only and are not considered standard.  
1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safet...

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM F747-22(Terminology)
Standard Terminology Relating to Amusement Rides and Devices

SCOPE
1.1 This terminology is a repository of terms approved by Committee F24 and its subcommittees. Reproducing terms approved within all other individual F24 standards and guides, this terminology will provide a single location where terms related to amusement rides and devices are freely accessible to the public, committee members and can be maintained, updated and utilized as effective communication tools. Although published alphabetically, terms unique to a specific F24 standard or guide are indicated as such by the reference which follows the applicable term.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM F770-22(Practice)
Standard Practice for Ownership, Operation, Maintenance, and Inspection of Amusement Rides and Devices

SIGNIFICANCE AND USE
4.1 The purpose of this practice is to delineate information and to establish procedures for the operation, maintenance, inspection, and training for amusement rides and devices.
SCOPE
1.1 This practice provides guidelines for operations, maintenance, and inspection procedures for amusement rides and devices to be performed by the owner/operator.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM F1193-22(Practice)
Standard Practice for Quality, Manufacture, and Construction of Amusement Rides and Devices

SIGNIFICANCE AND USE
3.1 The purpose of this practice is to provide the minimum manufacturing requirements for amusement rides and devices and to provide the minimum requirements for a written quality assurance program for an amusement ride or device manufacturer, or component supplier. This is not intended to include suppliers of off-the-shelf components (for example, fasteners, electrical wire).
SCOPE
1.1 This practice establishes the minimum requirements for a quality assurance program and the manufacturing of amusement rides and devices (including major modifications).  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    11 pages
    English language
    sale 15% off
ASTM
ASTM F2974-22(Practice)
Standard Practice for Auditing Amusement Rides and Devices

SIGNIFICANCE AND USE
4.1 The purpose of this practice is to provide the minimum auditing requirements for audits of amusement rides and devices.  
4.2 An audit can include inspections, evaluations, or examinations during the design, manufacturing, installation, commissioning, operation, or major modification of an amusement ride or device.  
4.3 When audits are performed, they shall occur during the relevant stages of an amusement ride or device’s design, manufacture, installation, commissioning or major modification. This practice does not require recurring design, manufacturing, installation, commissioning, or major modification audits.
SCOPE
1.1 This practice establishes minimum requirements for auditing conformance to ASTM Committee F24 Standards during an audit of an amusement ride or device within a defined scope.  
1.2 Defined scope of audit shall include but not be limited to the following:  
1.2.1 Auditors sufficient relevant education, training, technical knowledge, certifications as appropriate, and experience to properly audit an amusement ride or device in accordance with subsection 5.1 of this standard.  
1.2.2 Visual acuity requirements (if applicable) in accordance with subsection 5.1.3 of this standard.  
1.2.3 Reference standards including published year.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off