ASTM D2513-16a

Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings

ABSTRACT
This specification covers the requirements and test methods for material, dimensions, hydrostatic burst strength, tensile strength, chemical resistance, sustained pressure, heat fusion, and impact resistance of plastic pipes, tubing, and fittings used for direct burial and reliner applications in fuel gas mains and services for the distribution of natural gas. This specification does not cover threaded pipe. The plastic used to make the pipes and fittings shall be virgin plastic or reworked plastic having Plastics Pipe Institute (PPI) long-term hydrostatic design stress and hydrostatic design basis rating.
SCOPE
1.1 This specification covers requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and rapid crack resistance of polyethylene pipe, tubing, and fittings for use in fuel gas mains and services for direct burial and reliner applications. The pipe and fittings covered by this specification are intended for use in the distribution of natural gas. Requirements for the qualifying of polyethylene systems for use with liquefied petroleum gas are also covered.  
1.1.1 This specification does not cover threaded pipe. Design considerations are discussed in Appendix X1. In-plant quality control programs are specified in Annex A1 and Annex A2.  
1.1.2 See Specification F2619/F2619M for polyethylene piping for pressure or non-pressure oil and gas producing applications to convey fluids such as oil, dry or wet gas, multiphase fluids, and non-potable oilfield water.  
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following is an index of the annexes and appendix in this specification:    
Annex  
Subject    
Annex A1  
In-Plant Quality Control for all materials up to 12 in.    
Annex A2  
In-Plant Quality Control for PE materials 14 in. and larger.  
Appendixes  
Subject  
Appendix X1  
Design Consideration  
1.5 The following precautionary caveat pertains only to the test method portion, Section 6, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 14-Dec-2016
• ICS: 23.040.20 - Plastics pipes
• ICS: 23.040.45 - Plastics fittings
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.60 - Gas

Relations

• Replaces: ASTM D2513-16 - Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
• Effective Date: 15-Dec-2016
• Replaced By: ASTM D2513-18 - Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
• Effective Date: 15-Apr-2018
• Referred By: ASTM F2634-15(2021) - Standard Test Method for Laboratory Testing of Polyethylene (PE) Butt Fusion Joints using Tensile-Impact Method
• Effective Date: 15-Dec-2016
• Referred By: ASTM F3508-21a - Standard Guide for In-Situ Pipeline Renovation As Dual-Wall Composite Pipeline by Push/Pull Installation of Compressed-Fit Shape-Memory-Polymer Tubular (SMPT)
• Effective Date: 15-Dec-2016
• Referred By: ASTM F2896-23 - Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids
• Effective Date: 15-Dec-2016
• Referred By: ASTM F1924-19 - Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing
• Effective Date: 15-Dec-2016
• Referred By: ASTM F2619/F2619M-20 - Standard Specification for High-Density Polyethylene (PE) Line Pipe
• Effective Date: 15-Dec-2016
• Referred By: ASTM F1973-21 - Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems
• Effective Date: 15-Dec-2016
• Referred By: ASTM F1962-22 - Standard Guide for Use of Maxi-Horizontal Directional Drilling for Placement of Polyethylene Pipe or Conduit Under Obstacles, Including River Crossings
• Effective Date: 15-Dec-2016
• Referred By: ASTM F1734-19 - Standard Practice for Qualification of a Combination of Squeeze Tool, Pipe, and Squeeze-Off Procedures to Avoid Long-Term Damage in Polyethylene (PE) Gas Pipe
• Effective Date: 15-Dec-2016
• Referred By: ASTM F2830-11(2017) - Standard Specification for Manufacture and Joining of Polyethylene (PE) Gas Pressure Pipe With a Peelable Polypropylene (PP) Outer Layer
• Effective Date: 15-Dec-2016
• Referred By: ASTM F2620-20ae2 - Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
• Effective Date: 15-Dec-2016
• Referred By: ASTM F1055-16a(2022) - Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing
• Effective Date: 15-Dec-2016
• Referred By: ASTM F905-04(2022) - Standard Practice for Qualification of Polyethylene Saddle-Fused Joints
• Effective Date: 15-Dec-2016
• Referred By: ASTM F2897-23 - Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances)
• Effective Date: 15-Dec-2016

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D2513 −16a An American National Standard
Standard Specification for
1
Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
This standard is issued under the fixed designation D2513; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* standard does not purport to address all of the safety concerns,
if any, associated with its use. It is the responsibility of the user
1.1 This specification covers requirements and test methods
of this standard to establish appropriate safety and health
for material dimensions and tolerances, hydrostatic burst
practices and determine the applicability of regulatory limita-
strength, chemical resistance, and rapid crack resistance of
tions prior to use.
polyethylenepipe,tubing,andfittingsforuseinfuelgasmains
and services for direct burial and reliner applications.The pipe
2. Referenced Documents
andfittingscoveredbythisspecificationareintendedforusein
2
2.1 ASTM Standards:
the distribution of natural gas. Requirements for the qualifying
2.1.1 Terminology:
of polyethylene systems for use with liquefied petroleum gas
D1600TerminologyforAbbreviatedTermsRelatingtoPlas-
are also covered.
tics
1.1.1 This specification does not cover threaded pipe. De-
F412Terminology Relating to Plastic Piping Systems
sign considerations are discussed in Appendix X1. In-plant
2.1.2 Test Methods for:
qualitycontrolprogramsarespecifiedinAnnexA1andAnnex
D638Test Method for Tensile Properties of Plastics
A2.
D1238Test Method for Melt Flow Rates of Thermoplastics
1.1.2 See Specification F2619/F2619M for polyethylene
by Extrusion Plastometer
piping for pressure or non-pressure oil and gas producing
D1598Test Method for Time-to-Failure of Plastic Pipe
applications to convey fluids such as oil, dry or wet gas,
Under Constant Internal Pressure
multiphase fluids, and non-potable oilfield water.
D1599Test Method for Resistance to Short-Time Hydraulic
1.2 Thetextofthisspecificationreferencesnotes,footnotes,
Pressure of Plastic Pipe, Tubing, and Fittings
and appendixes which provide explanatory material. These
D2122Test Method for Determining Dimensions of Ther-
notesandfootnotes(excludingthoseintablesandfigures)shall
moplastic Pipe and Fittings
not be considered as requirements of the specification.
D2290Test Method for Apparent Hoop Tensile Strength of
1.3 Thevaluesstatedininch-poundunitsaretoberegarded
Plastic or Reinforced Plastic Pipe
as standard. The values given in parentheses are mathematical
D2837Test Method for Obtaining Hydrostatic Design Basis
conversions to SI units that are provided for information only
forThermoplasticPipeMaterialsorPressureDesignBasis
and are not considered standard.
for Thermoplastic Pipe Products
F1473Test Method for Notch Tensile Test to Measure the
1.4 The following is an index of the annexes and appendix
Resistance to Slow Crack Growth of Polyethylene Pipes
in this specification:
and Resins
Annex Subject
2.1.3 Practices for:
Annex A1 In-Plant Quality Control for all materials up to 12 in.
Annex A2 In-Plant Quality Control for PE materials 14 in. and larger.
D543Practices for Evaluating the Resistance of Plastics to
Chemical Reagents
Appendixes Subject
D618Practice for Conditioning Plastics for Testing
Appendix Design Consideration
X1
D1435Practice for Outdoor Weathering of Plastics
3
1.5 The following precautionary caveat pertains only to the
D1898Practice for Sampling of Plastics (Withdrawn 1998)
test method portion, Section 6, of this specification. This
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Piping Systems and is the direct responsibility of Subcommittee F17.60 on Gas. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Dec. 15, 2016. Published February 2017. Originally the ASTM website.
3
approved in 1966. Last previous edition approved in 2016 as D2513–16. DOI: The last approved version of this historical standard is referenced on
10.1520/D2513-16A. www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D2513−16a
D2774PracticeforUndergroundInstallationofThermoplas- ISO 12162Thermoplastic Materials for Pipes and Fittings
tic Pressure Piping f
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D2513 − 16 D2513 − 16a An American National Standard
Standard Specification for
1
Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
This standard is issued under the fixed designation D2513; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This specification covers requirements and test methods for material dimensions and tolerances, hydrostatic burst strength,
chemical resistance, and rapid crack resistance of polyethylene pipe, tubing, and fittings for use in fuel gas mains and services for
direct burial and reliner applications. The pipe and fittings covered by this specification are intended for use in the distribution of
natural gas. Requirements for the qualifying of polyethylene systems for use with liquefied petroleum gas are also covered.
1.1.1 This specification does not cover threaded pipe. Design considerations are discussed in Appendix X1. In-plant quality
control programs are specified in Annex A1 and Annex A2.
1.1.2 See Specification F2619/F2619M for polyethylene piping for pressure or non-pressure oil and gas producing applications
to convey fluids such as oil, dry or wet gas, multiphase fluids, and non-potable oilfield water.
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes
and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 The following is an index of the annexes and appendix in this specification:
Annex Subject
Annex A1 In-Plant Quality Control for all materials up to 12 in.
Annex A2 In-Plant Quality Control for PE materials 14 in. and larger.
Appendixes Subject
Appendix Design Consideration
X1
1.5 The following precautionary caveat pertains only to the test method portion, Section 6, of this specification.This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
2.1.1 Terminology:
D1600 Terminology for Abbreviated Terms Relating to Plastics
F412 Terminology Relating to Plastic Piping Systems
2.1.2 Test Methods for:
D638 Test Method for Tensile Properties of Plastics
D1238 Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
D1598 Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
D1599 Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2290 Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.60 on Gas.
Current edition approved Dec. 1, 2016Dec. 15, 2016. Published January 2017February 2017. Originally approved in 1966. Last previous edition approved in 20142016
ɛ1
as D2513 – 14D2513 – 16. . DOI: 10.1520/D2513-16.10.1520/D2513-16A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D2513 − 16a
D2837 Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for
Thermoplastic Pipe Products
F1473 Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins
2.1.3 Practices for:
D543 Practices for Eval
...