ASTM F1890-17(2022)

Standard Test Method for Measuring Softball and Baseball Bat Performance Factor

SIGNIFICANCE AND USE
4.1 These test methods offer a laboratory means to quantitatively compare the performance of softball and baseball bats.
SCOPE
1.1 A method for determining bat performance by measuring the bat-ball coefficient of restitution (BBCOR) and deriving the bat performance factor (BPF). It is applicable to softball and baseball bats of any construction or material. The method provides a quantitative measure of bat dynamic performance that may be used for comparison purposes.  
1.2 The BBCOR and BPF are calculated from measurements taken in the laboratory on test equipment meeting the requirements defined in this method.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 31-Aug-2022
• ICS: 97.220.40 - Outdoor and water sports equipment
• Technical Committee: F08 - Sports Equipment, Playing Surfaces, and Facilities
• Drafting Committee: F08.26 - Baseball and Softball Equipment

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F1890 − 17 (Reapproved 2022) An American National Standard
Standard Test Method for
Measuring Softball and Baseball Bat Performance Factor
This standard is issued under the fixed designation F1890; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3. Terminology
1.1 A method for determining bat performance by measur- 3.1 Definitions of Terms Specific to This Standard:
ing the bat-ball coefficient of restitution (BBCOR) and deriving 3.1.1 balance point (BP), n—distance to the center of mass
the bat performance factor (BPF). It is applicable to softball of a bat when measured from the knob end of the bat.
and baseball bats of any construction or material. The method
3.1.2 coeffıcient of restitution (COR), n—the relative speed
provides a quantitative measure of bat dynamic performance
of the objects after impact divided by the relative speed of the
that may be used for comparison purposes.
objects before impact.
1.2 The BBCOR and BPF are calculated from measure-
3.1.3 bat-ball coeffıcient of restitution (BBCOR), n—COR
ments taken in the laboratory on test equipment meeting the
of a specific ball colliding with a bat as defined in this test
requirements defined in this method.
method.
1.3 The values stated in inch-pound units are to be regarded
3.1.4 bat performance factor (BPF), n—ratio of BBCOR to
as standard. The values given in parentheses are units that are
ball COR as defined in this test method.
provided for information only and are not considered standard.
3.1.5 center of percussion (COP), n—impact location on the
1.4 This standard does not purport to address all of the
bat that produces no reaction force at the pivot point and causes
safety concerns, if any, associated with its use. It is the
the bat to rotate about the pivot point, taken 6 in. (152 mm)
responsibility of the user of this standard to establish appro-
from the knob end of the bat.
priate safety, health, and environmental practices and deter-
3.1.6 moment of inertia (MOI), n—measure of mass distri-
mine the applicability of regulatory limitations prior to use.
bution relative to a pivot point, taken 6 in. (152 mm) from the
1.5 This international standard was developed in accor-
knob end of the bat.
dance with internationally recognized principles on standard-
4. Significance and Use
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
4.1 These test methods offer a laboratory means to quanti-
mendations issued by the World Trade Organization Technical
tatively compare the performance of softball and baseball bats.
Barriers to Trade (TBT) Committee.
5. Apparatus
2. Referenced Documents
5.1 Test Balls—Softballs or baseballs as determined by
those specifying the bat test requirements and tested in
2.1 ASTM Standards:
accordance with the following procedures. Perform ball com-
F1887 Test Method for Measuring the Coefficient of Resti-
pression test of Test Method F1888 prior to ball COR test of
tution (COR) of Baseballs and Softballs
Test Method F1887.
F1888 Test Method for Compression-Displacement of Base-
5.1.1 Softballs:
balls and Softballs
5.1.1.1 Compression—350 to 375 lb (1557 to 1688 N) (Test
F2398 Test Method for Measuring Moment of Inertia and
Method F1888.)
Center of Percussion of a Baseball or Softball Bat
5.1.1.2 Weight—6.25 to 6.75 oz (177.2 to 191.4 g).
5.1.1.3 Size—12.00 to 12.25-in. (304.8 to 311.1-mm) cir-
This test method is under the jurisdiction of ASTM Committee F08 on Sports cumference (Test Method F1888).
Equipment, Playing Surfaces, and Facilities and is the direct responsibility of
5.1.1.4 Ball COR—0.465 to 0.475 (Test Method F1887).
Subcommittee F08.26 on Baseball and Softball Equipment.
5.1.2 Baseballs:
Current edition approved Sept. 1, 2022. Published October 2022. Originally
ɛ1
5.1.2.1 Compression—175 to 200 lb (778 to 890 N) (Test
approved in 1998. Last previous edition approved in 2017 as F1890 – 17 . DOI:
10.1520/F1890-17R22.
Method F1888 using 0.20 in. (5.08 mm) deflection).
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
5.1.2.2 Weight—5.00 to 5.25 oz (141.8 to 148.8 g).
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
5.1.2.3 Size—9.00 to 9.50 in. (228.6 to 241.3 mm) circum-
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. ference (Test Method F1888).
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F1890 − 17 (2022)
5.1.2.4 Ball COR—0.545 to 0.555 (Test Method F1887). 6. Calibration and Standardization
5.2 Bat-Ball COR Test Apparatus: 6.1 Ball Speed Gate—The distances between the sensors of
5.2.1 Ball Cannon—A device capable of shooting a ball at a the speed gates must be measured and recorded to the stated
speed of at least 88 ft/s (26.8 m/s). The ball shall not have a tolerances. The accuracy of the timers used in the velocity
spin rate in excess of 10 rpm. Typical pitching machines cannot sensors must be adequate to provide the stated velocity
yield the aiming accuracy required by this test method. Cannon accuracy at maximum stated speeds. The timers used shall be
exhaust air must not cause motion of the bat in the absence of calibrated on at least a yearly basis.
an impact. The ball cannon can be any distance from impact
6.2 Reference Standards and Blanks—A standard bat and
location, as long as it can meet the ball aim requirements and
ball shall be used for reference purposes to verify proper
provide six valid impacts in twelve shots or less.
machine operation.
5.2.2 Bat Speed Gate—A light-trap device, or an equivalent,
6.3 Calibration:
capable of measuring an edge traveling at speeds of between 5
6.3.1 Determine the balance point (BP), MOI, and COP of a
and 15 ft/s with a resolution of 0.01 ft/s (0.003 m/s) and an
large calibration mass (MOI ≥ 30 000 oz-in. (549 000 kg-
accuracy of at least 61 %. The first sensor shall trigger after
mm )) in accordance with Test Method F2398.
the bat rotates between 5 to 10° from its start position. The
6.3.2 Mount the large calibration mass in the bat pivot
second sensor shall trigger 30 to 35° after the first sensor.
support clamps per 8.2.4.
Reference Fig. 1.
6.3.3 Select a test ball in accordance with 5.1 as determined
5.2.2.1 Optional Bat Speed Sensor—Device to measure bat
by those specifying the bat test, and record the actual values of
rotational speed for at least 100° after impact. Device shall read
compression, weight, size, and COR of the ball in accordance
speeds up to 3000°/s with an accuracy of at least 1°/s (found to
with 5.1.
be achievable using an optical encoder). Bat speed is taken
6.3.4 Shoot the ball at the calibration mass COP, observing
from the slope of the linear least-squares fit to the bat rotation
the necessary safety precautions and in accordance with
angle versus time data between 5 and 95° after impact.
Section 8 except as noted.
5.2.3 Ball Speed Gate—A light-trap device, or an
6.3.5 Determine K as follows:
equivalent, capable of measuring a sphere traveling at speeds calibration
in excess of 88 ft/s (26.8 m/s) with an accuracy of 0.5 ft/s (0.2
11Ball COR 11Ball COR
K 5 5
calibration
m/s) or better. The device shall measure across a length of no
I1I t D R I1I V
p p bat
1 1 1 1
S DS DS DS D S DS D
2 2
less than half the ball diameter to avoid centering error. The
mR d T r mR v
i
distance between the two sensors shall be determined to within
(1)
60.03 in. (60.76 mm) and must be between 6 and 12 in. (152
where:
and 305 mm). Prior to impact, the sensor closest to the bat must
Ball COR = ball COR (Test Method F1887) of the ball used
be between 4 and 6 in. (102 and 152 mm) from the bat.
in each impact,
Reference Fig. 1.
I = moment of inertia (MOI) of mass, Test Method
5.2.4 Bat Pivot Support—A turntable, rotating in the hori-
2 2
F2398, oz-in. (kg-m ),
zontal plane, with clamps to support and align the bat in the
I = moment of inertia (MOI) of bat pivot, oz-in.
path of the ball. The clamp surfaces shall be a 45° v-clamp with p
(kg-m ),
a radius no greater than 2.0 in. (50.8 mm). The rotating clamp
R = COP distance, Test Method F2398, in. (m),
and shaft assembly shall not weigh more than 6 lb (2.7 kg) and
r = radius to bat speed sensors, in. (m),
shall spin freely via ball bearings (see Fig. 1). The polar MOI
T = time for bat to travel through bat speed sensors,
for the clamp turntable assembly shall not exceed 300 oz-
s,
2 2
in. (5498 kg-mm ).
FIG. 1 Bat Testing Machine
F1890 − 17 (2022)
8.2.9 Shoot the ball at the bat, observing the necessary
t = time for ball to travel through ball speed
safety precautions.
sensors, s,
8.2.10 Record ball inbound speed and bat rebound speed.
D = distance between bat speed sensors, in. (m),
d = distance between ball speed sensors, in. (m), 8.2.10.1 Optional—Record ball rebound speed. The ball
v = ball inbound speed, in./s (m/s),
rebound angle immediately after impact should be within 610°
i
V = bat recoiling spe
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: F1890 − 17 F1890 − 17 (Reapproved 2022) An American National Standard
Standard Test Method for
Measuring Softball and Baseball Bat Performance Factor
This standard is issued under the fixed designation F1890; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
ε NOTE—Editorially corrected 5.2.2 in February 2018.
1. Scope
1.1 A method for determining bat performance by measuring the bat-ball coefficient of restitution (BBCOR) and deriving the bat
performance factor (BPF). It is applicable to softball and baseball bats of any construction or material. The method provides a
quantitative measure of bat dynamic performance that may be used for comparison purposes.
1.2 The BBCOR and BPF are calculated from measurements taken in the laboratory on test equipment meeting the requirements
defined in this method.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are units that are provided
for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2.1 ASTM Standards:
F1887 Test Method for Measuring the Coefficient of Restitution (COR) of Baseballs and Softballs
F1888 Test Method for Compression-Displacement of Baseballs and Softballs
F2398 Test Method for Measuring Moment of Inertia and Center of Percussion of a Baseball or Softball Bat
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 balance point (BP), n—distance to the center of mass of a bat when measured from the knob end of the bat.
3.1.2 coeffıcient of restitution (COR), n—the relative speed of the objects after impact divided by the relative speed of the objects
before impact.
This test method is under the jurisdiction of ASTM Committee F08 on Sports Equipment, Playing Surfaces, and Facilities and is the direct responsibility of Subcommittee
F08.26 on Baseball and Softball Equipment.
Current edition approved Aug. 15, 2017Sept. 1, 2022. Published January 2018October 2022. Originally approved in 1998. Last previous edition approved in 20112017
ɛ1
as F1890 – 11.F1890 – 17 . DOI: 10.1520/F1890-17E01.10.1520/F1890-17R22.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F1890 − 17 (2022)
3.1.3 bat-ball coeffıcient of restitution (BBCOR), n—COR of a specific ball colliding with a bat as defined in this test method.
3.1.4 bat performance factor (BPF), n—ratio of BBCOR to ball COR as defined in this test method.
3.1.5 center of percussion (COP), n—impact location on the bat that produces no reaction force at the pivot point and causes the
bat to rotate about the pivot point, taken 6 in. (152 mm) from the knob end of the bat.
3.1.6 moment of inertia (MOI), n—measure of mass distribution relative to a pivot point, taken 6 in. (152 mm) from the knob end
of the bat.
4. Significance and Use
4.1 These test methods offer a laboratory means to quantitatively compare the performance of softball and baseball bats.
5. Apparatus
5.1 Test Balls—Softballs or baseballs as determined by those specifying the bat test requirements and tested in accordance with
the following procedures. Perform ball compression test of Test Method F1888 prior to ball COR test of Test Method F1887.
5.1.1 Softballs:
5.1.1.1 Compression—350 to 375 lb (1557 to 1688 N) (Test Method F1888.)
5.1.1.2 Weight—6.25 to 6.75 oz (177.2 to 191.4 g).
5.1.1.3 Size—12.00 to 12.25-in. (304.8 to 311.1-mm) circumference (Test Method F1888).
5.1.1.4 Ball COR—0.465 to 0.475 (Test Method F1887).
5.1.2 Baseballs:
5.1.2.1 Compression—175 to 200 lb (778 to 890 N) (Test Method F1888 using 0.20 in. (5.08 mm) deflection).
5.1.2.2 Weight—5.00 to 5.25 oz (141.8 to 148.8 g).
5.1.2.3 Size—9.00 to 9.50 in. (228.6 to 241.3 mm) circumference (Test Method F1888).
5.1.2.4 Ball COR—0.545 to 0.555 (Test Method F1887).
5.2 Bat-Ball COR Test Apparatus:
5.2.1 Ball Cannon—A device capable of shooting a ball at a speed of at least 88 ft/s (26.8 m/s). The ball shall not have a spin rate
in excess of 10 rpm. Typical pitching machines cannot yield the aiming accuracy required by this test method. Cannon exhaust
air must not cause motion of the bat in the absence of an impact. The ball cannon can be any distance from impact location, as
long as it can meet the ball aim requirements and provide six valid impacts in twelve shots or less.
5.2.2 Bat Speed Gate—A light-trap device, or an equivalent, capable of measuring an edge traveling at speeds of between 5 and
15 ft/s with a resolution of 0.01 ft/s (0.003 m/s) and an accuracy of at least 61 %. The first sensor shall trigger after the bat rotates
between 5 to 10° from its start position. The second sensor shall trigger 30 to 35° after the first sensor. Reference Fig. 1.
5.2.2.1 Optional Bat Speed Sensor—Device to measure bat rotational speed for at least 100° after impact. Device shall read speeds
up to 3000°/s with an accuracy of at least 1°/s (found to be achievable using an optical encoder). Bat speed is taken from the slope
of the linear least-squares fit to the bat rotation angle versus time data between 5 and 95° after impact.
5.2.3 Ball Speed Gate—A light-trap device, or an equivalent, capable of measuring a sphere traveling at speeds in excess of 88
ft/s (26.8 m/s) with an accuracy of 0.5 ft/s (0.2 m/s) or better. The device shall measure across a length of no less than half the
F1890 − 17 (2022)
FIG. 1 Bat Testing Machine
ball diameter to avoid centering error. The distance between the two sensors shall be determined to within 60.03 in. (60.76 mm)
and must be between 6 and 12 in. (152 and 305 mm). Prior to impact, the sensor closest to the bat must be between 4 and 6 in.
(102 and 152 mm) from the bat. Reference Fig. 1.
5.2.4 Bat Pivot Support—A turntable, rotating in the horizontal plane, with clamps to support and align the bat in the path of the
ball. The clamp surfaces shall be a 45° v-clamp with a radius no greater than 2.0 in. (50.8 mm). The rotating clamp and shaft
assembly shall not weigh more than 6 lb (2.7 kg) and shall spin freely via ball bearings (see Fig. 1). The polar MOI for the clamp
2 2
turntable assembly shall not exceed 300 oz-in. (5498 kg-mm ).
6. Calibration and Standardization
6.1 Ball Speed Gate—The distances between the sensors of the speed gates must be measured and recorded to the stated
tolerances. The accuracy of the timers used in the velocity sensors must be adequate to provide the stated velocity accuracy at
maximum stated speeds. The timers used shall be calibrated on at least a yearly basis.
6.2 Reference Standards and Blanks—A standard bat and ball shall be used for reference purposes to verify proper machine
operation.
6.3 Calibration:
2 2
6.3.1 Determine the balance point (BP), MOI, and COP of a large calibration mass (MOI ≥ 30 000 oz-in. (549 000 kg-mm )) in
accordance with Test Method F2398.
6.3.2 Mount the large calibration mass in the bat pivot support clamps per 8.2.4.
6.3.3 Select a test ball in accordance with 5.1 as determined by those specifying the bat test, and record the actual values of
compression, weight, size, and COR of the ball in accordance with 5.1.
6.3.4 Shoot the ball at the calibration mass COP, observing the necessary safety precautions and in accordance with Section 8
except as noted.
6.3.5 Determine K as follows:
calibration
11Ball COR 11Ball COR
K 5 5 (1)
calibration
I1I t D R I1I V
p p bat
1 1 1 1
S DS DS DS D S DS D
2 2
mR d T r mR v
i
where:
Ball COR = ball COR (Test Method F1887) of the ball used in each impact,
F1890 − 17 (2022)
2 2
I = moment of inertia (MOI) of mass, Test Method F2398, oz-in. (kg-m ),
2 2
I = moment of inertia (MOI) of bat pivot, oz-in. (kg-m ),
p
R = COP distance, Test Method F2398, in. (m),
r = radius to bat speed sensors, in. (m),
T = time for bat to travel through bat speed sensors, s,
t = time for ball to travel through ball speed sensors, s,
D = distance between bat speed sensors, in. (m),
d = distance between ball speed sensors, in. (m),
v = ball inbound speed, in./s (m/s),
i
V = bat recoiling speed at the impact location, in./s (m/s), and
bat
m = weight of the test ball used in each impact, oz (g)
...