ASTM B249/B249M-09
(Specification)Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
ABSTRACT
This specification establishes the general requirements common to wrought copper and copper alloy rods, bars, shapes, and forgings. Products shall be manufactured by hot working, cold working, or both, and finished by cold working, annealing, or heat treatment and straightening as identified necessary to meet the properties specified. Materials shall be sampled and prepared, then tested accordingly to examine their conformance to dimensional (mass, diameter, length, straightness, and edge contours), mechanical (tensile strength, Rockwell hardness, elongation, and hydrogen embrittlement), electrical resistivity, chemical composition, and grain size requirements. The products shall also meet performance requirements when subjected to residual stress, mercurous nitrate, ammonia vapor, and semiguided bend tests. In the event of conflict between this specification and the individual casting product specifications, the requirements of the casting specification shall take precedence.
SIGNIFICANCE AND USE
For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table and for dimensional tolerances, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29.
Property Rounded Unit for Observed or
Calculated Value Chemical compositionnearest unit in the last right-hand significant digit used in expressing the limiting value Hardness Electrical resistivity Electrical conductivity Tensile strengthnearest ksi [5 MPa] Yield strength Elongation:nearest 1 % Grain size: Under 0.060 mmnearest multiple of 0.005 mm 0.060 mm and overnearest 0.01 mm
SCOPE
1.1 This specification establishes the general requirements common to wrought copper and copper alloy rod, bar, shapes, and forgings which shall apply to Specifications B16/B16M, B21/B21M, B98/B98M, B124/B124M, B138/B138M, B139/B139M, B140/B140M, B150/B150M, B151/B151M, B196/B196M, B283, B301/B301M, B371/B371M, B411/B411M, B441, B453/B453M, B455, B570, and B927 to the extent referenced therein.
1.2 The chemical composition, physical and mechanical properties, and all other requirements not included in this specification are prescribed in the product specification.
1.3 The values stated in inch-pounds units or SI units are to be regarded separately in the standard. Within the text the SI values are given in brackets. The values stated in each system of units are not exact equivalents; each system is independent of the other. Combining values from the two systems may result in nonconformance with the specification.
Note 1—Requirements for flat wire (defined as flat products up to and including 0.188 in. thick and up to 1¼ in. in width, with all surfaces rolled or drawn, without having been slit, sheared or sawed) including square, furnished in coils or straight lengths, or on spools, reels, or bucks are described by the wire Specifications B206/B206M and B272.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information.
Designation: B249/B249M – 09
Standard Specification for
General Requirements for Wrought Copper and Copper-
1
Alloy Rod, Bar, Shapes and Forgings
This standard is issued under the fixed designation B249/B249M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* 2. Referenced Documents
2 3
1.1 This specification establishes the general requirements 2.1 ASTM Standards:
common to wrought copper and copper alloy rod, bar, shapes, B16/B16M Specification for Free-Cutting Brass Rod, Bar
and forgings which shall apply to Specifications B16/B16M, and Shapes for Use in Screw Machines
B21/B21M, B98/B98M, B124/B124M, B138/B138M, B139/ B21/B21M Specification for Naval Brass Rod, Bar, and
B139M, B140/B140M, B150/B150M, B151/B151M, B196/ Shapes
B196M, B283, B301/B301M, B371/B371M, B411/B411M, B98/B98M SpecificationforCopper-SiliconAlloyRod,Bar
B441, B453/B453M, B455, B570, and B927 to the extent and Shapes
referenced therein. B124/B124M Specification for Copper and Copper Alloy
1.2 The chemical composition, physical and mechanical Forging Rod, Bar, and Shapes
properties, and all other requirements not included in this B138/B138M Specification for Manganese Bronze Rod,
specification are prescribed in the product specification. Bar, and Shapes
1.3 The values stated in inch-pounds units or SI units are to B139/B139M Specification for Phosphor Bronze Rod, Bar,
be regarded separately in the standard. Within the text the SI and Shapes
values are given in brackets. The values stated in each system B140/B140M Specification for Copper-Zinc-Lead (Red
of units are not exact equivalents; each system is independent Brass or Hardware Bronze) Rod, Bar, and Shapes
of the other. Combining values from the two systems may B150/B150M Specification for Aluminum Bronze Rod,
result in nonconformance with the specification. Bar, and Shapes
B151/B151M Specification for Copper-Nickel-Zinc Alloy
NOTE 1—Requirements for flat wire (defined as flat products up to and
(Nickel Silver) and Copper-Nickel Rod and Bar
1
including0.188in.thickandupto1 ⁄4in.inwidth,withallsurfacesrolled
B154 Test Method for Mercurous Nitrate Test for Copper
or drawn, without having been slit, sheared or sawed) including square,
furnished in coils or straight lengths, or on spools, reels, or bucks are Alloys
described by the wire Specifications B206/B206M and B272.
B187/B187M Specification for Copper, Bus Bar, Rod, and
Shapes and General Purpose Rod, Bar, and Shapes
1.4 This standard does not purport to address all of the
B193 Test Method for Resistivity of Electrical Conductor
safety concerns, if any, associated with its use. It is the
Materials
responsibility of the user of this standard to establish appro-
B194 Specification for Copper-Beryllium Alloy Plate,
priate safety and health practices and determine the applica-
Sheet, Strip, and Rolled Bar
bility of regulatory limitations prior to use.
B196/B196M Specification for Copper-Beryllium Alloy
Rod and Bar
B206/B206M Specification for Copper-Nickel-Zinc (Nickel
Silver) Wire and Copper-Nickel Alloy Wire
B272 Specification for Copper Flat Products with Finished
(Rolled or Drawn) Edges (Flat Wire and Strip)
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB05onCopper
and CopperAlloys and is the direct responsibility of Subcommittee B05.02 on Rod,
Bar, Wire, Shapes and Forgings.
Current edition approved Oct. 1, 2009. Published November 2009. Originally
3
approved in 1951. Last previous edition approved in 2006 as B249/B249M – 06. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
DOI: 10.1520/B0249_B0249M-09. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi- Standards volume information, refer to the standard’s Document Summary page on
cations SB-249 in Section II of that Code. the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B249/B249M – 09
B283 Specification for Copper and Copper-Alloy Die Forg- E581 Test Methods for Chemical Analysis of Manganese-
ings (Hot-Pressed) Copper Alloys
B301/B301M Specification for Free-Cutting Copper Rod,
Bar, Wire, and Shapes 3. Terminology
B371/B371M Specification for Copper-Zinc-Silicon Alloy
3.1 Definitions:
Rod
3.1.1 bar, n—a solid rectangular section, or one with
B411/B411M Specification f
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B249/B249M–06 Designation: B249/B249M – 09
Standard Specification for
General Requirements for Wrought Copper and Copper-
1
Alloy Rod, Bar, Shapes and Forgings
This standard is issued under the fixed designation B249/B249M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This specification establishes the general requirements common to wrought copper and copper alloy rod, bar, shapes, and
forgings which shall apply to Specifications B16/B16M, B21/B21M, B98/B98M, B124/B124M, B138/B138M, B139/B139M,
B140/B140M, B150/B150M, B151/B151M, B196/B196M, B283, B301/B301M, B371/B371M, B411/B411M, B441, B453/
B453M, B455, B570, and B927 to the extent referenced therein.
1.2 The chemical composition, physical and mechanical properties, and all other requirements not included in this specification
are prescribed in the product specification.
1.3 The values stated in inch-pounds units or SI units are to be regarded separately in the standard.Within the text the SI values
are given in brackets. The values stated in each system of units are not exact equivalents; each system is independent of the other.
Combining values from the two systems may result in nonconformance with the specification.
1
NOTE 1—Requirements for flat wire (defined as flat products up to and including 0.188 in. thick and up to 1 ⁄4 in. in width, with all surfaces rolled
or drawn, without having been slit, sheared or sawed) including square, furnished in coils or straight lengths, or on spools, reels, or bucks are described
by the wire Specifications B206/B206M and B272B206/B206MB272and B272.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
B16/B16M Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines
B21/B21M Specification for Naval Brass Rod, Bar, and Shapes
B98/B98M Specification for Copper-Silicon Alloy Rod, Bar and Shapes
B124/B124M Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes
B138/B138M Specification for Manganese Bronze Rod, Bar, and Shapes
B139/B139M Specification for Phosphor Bronze Rod, Bar, and Shapes
B140/B140M Specification for Copper-Zinc-Lead (Red Brass or Hardware Bronze) Rod, Bar, and Shapes
B150/B150M Specification for Aluminum Bronze Rod, Bar, and Shapes
B151/B151M Specification for Copper-Nickel-Zinc Alloy (Nickel Silver) and Copper-Nickel Rod and Bar
B154 Test Method for Mercurous Nitrate Test for Copper Alloys
B187/B187M Specification for Copper, Bus Bar, Rod, and Shapes and General Purpose Rod, Bar, and Shapes
B193 Test Method for Resistivity of Electrical Conductor Materials
B194 Specification for Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar
B196/B196M Specification for Copper-Beryllium Alloy Rod and Bar
B206/B206M Specification for Copper-Nickel-Zinc (Nickel Silver) Wire and Copper-Nickel Alloy Wire
1
This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.02 on Rod,
Bar, Wire, Shapes and Forgings.
´1
Current edition approved Feb. 1, 2006. Published February 2006. Originally approved in 1951. Last previous edition approved in 2004 as B249/B249M–04 . DOI:
10.1520/B0249_B0249M-06.
Current edition approved Oct. 1, 2009. Published November 2009. Originally approved in 1951. Last previous edition approved in 2006 as B249/B249M – 06. DOI:
10.1520/B0249_B0249M-09.
2
For ASME Boiler and Pressure Vessel Code applications see related Specifications SB-249 in Section II of that Code.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B249/B249M–06 Designation: B249/B249M – 09
Standard Specification for
General Requirements for Wrought Copper and Copper-
1
Alloy Rod, Bar, Shapes and Forgings
This standard is issued under the fixed designation B249/B249M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This specification establishes the general requirements common to wrought copper and copper alloy rod, bar, shapes, and
forgings which shall apply to Specifications B16/B16M, B21/B21M, B98/B98M, B124/B124M, B138/B138M, B139/B139M,
B140/B140M, B150/B150M, B151/B151M, B196/B196M, B283, B301/B301M, B371/B371M, B411/B411M, B441, B453/
B453M, B455, B570, and B927 to the extent referenced therein.
1.2 The chemical composition, physical and mechanical properties, and all other requirements not included in this specification
are prescribed in the product specification.
1.3 The values stated in inch-pounds units or SI units are to be regarded separately in the standard.Within the text the SI values
are given in brackets. The values stated in each system of units are not exact equivalents; each system is independent of the other.
Combining values from the two systems may result in nonconformance with the specification.
1
NOTE 1—Requirements for flat wire (defined as flat products up to and including 0.188 in. thick and up to 1 ⁄4 in. in width, with all surfaces rolled
or drawn, without having been slit, sheared or sawed) including square, furnished in coils or straight lengths, or on spools, reels, or bucks are described
by the wire Specifications B206/B206M and B272B206/B206MB272and B272.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
B16/B16M Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines
B21/B21M Specification for Naval Brass Rod, Bar, and Shapes
B98/B98M Specification for Copper-Silicon Alloy Rod, Bar and Shapes
B124/B124M Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes
B138/B138M Specification for Manganese Bronze Rod, Bar, and Shapes
B139/B139M Specification for Phosphor Bronze Rod, Bar, and Shapes
B140/B140M Specification for Copper-Zinc-Lead (Red Brass or Hardware Bronze) Rod, Bar, and Shapes
B150/B150M Specification for Aluminum Bronze Rod, Bar, and Shapes
B151/B151M Specification for Copper-Nickel-Zinc Alloy (Nickel Silver) and Copper-Nickel Rod and Bar
B154 Test Method for Mercurous Nitrate Test for Copper Alloys
B187/B187M Specification for Copper, Bus Bar, Rod, and Shapes and General Purpose Rod, Bar, and Shapes
B193 Test Method for Resistivity of Electrical Conductor Materials
B194 Specification for Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar
B196/B196M Specification for Copper-Beryllium Alloy Rod and Bar
B206/B206M Specification for Copper-Nickel-Zinc (Nickel Silver) Wire and Copper-Nickel Alloy Wire
1
This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.02 on Rod,
Bar, Wire, Shapes and Forgings.
´1
Current edition approved Feb. 1, 2006. Published February 2006. Originally approved in 1951. Last previous edition approved in 2004 as B249/B249M–04 . DOI:
10.1520/B0249_B0249M-06.
Current edition approved Oct. 1, 2009. Published November 2009. Originally approved in 1951. Last previous edition approved in 2006 as B249/B249M – 06. DOI:
10.1520/B0249_B0249M-09.
2
For ASME Boiler and Pressure Vessel Code applications see related Specifications SB-249 in Section II of that Code.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.