ASTM F2509-12
(Specification)Standard Specification for Field-assembled Anodeless Riser Kits for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing
Standard Specification for Field-assembled Anodeless Riser Kits for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing
ABSTRACT
This specification covers the qualification requirements and test methods for field-assembled anodeless riser kits for use with outside diameter controlled polyethylene gas distribution pipes and tubing in sizes of up to 2 IPS. The anodeless riser kits shall be manufactured in accordance with the specified materials, physical properties, and design, which include the riser casings, moisture seals, threads, bend radius, coatings, welding procedures, and riser adapter to riser casing connections. The riser adapter to riser casing connections shall tested by tensile pull testing.
SCOPE
1.1 This specification covers requirements and test methods for field-assembled anodeless riser kits for use with outside diameter controlled polyethylene gas distribution pipe and tubing in sizes through 2 IPS as specified in specification D2513.
1.2 The test methods described are not intended to be routine quality control tests.
1.3 This specification covers the types of field-assembled anodeless riser kits described in 3.3.2.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and not considered standard.
1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures), shall not be considered as requirements of the standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F2509 −12
StandardSpecification for
Field-assembled Anodeless Riser Kits for Use on Outside
Diameter Controlled Polyethylene Gas Distribution Pipe and
1
Tubing
This standard is issued under the fixed designation F2509; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D638 Test Method for Tensile Properties of Plastics
D1600 Terminology forAbbreviatedTerms Relating to Plas-
1.1 This specification covers requirements and test methods
tics
for field-assembled anodeless riser kits for use with outside
D2513 Specification for Polyethylene (PE) Gas Pressure
diameter controlled polyethylene gas distribution pipe and
Pipe, Tubing, and Fittings
tubing in sizes through 2 IPS as specified in specification
F412 Terminology Relating to Plastic Piping Systems
D2513.
F1948 Specification for Metallic Mechanical Fittings for
1.2 The test methods described are not intended to be
Use on Outside Diameter Controlled Thermoplastic Gas
routine quality control tests.
Distribution Pipe and Tubing
F2897 Specification for Tracking and Traceability Encoding
1.3 This specification covers the types of field-assembled
anodeless riser kits described in 3.3.2. System of Natural Gas Distribution Components (Pipe,
Tubing, Fittings, Valves, and Appurtenances)
1.4 The values stated in inch-pound units are to be regarded
3
2.2 ASME Standards:
as standard. The values given in parentheses are mathematical
3
ASME Boiler and Pressure Vessel Code
conversions to SI units that are provided for information only
4
ASME B1.20.1 Pipe Threads, General Purpose (Inch)
and not considered standard.
B31.8 Gas Transmission and Distribution Piping Systems
4
1.5 The text of this standard references notes and footnotes
2.3 Federal Regulations:
which provide explanatory material. These notes and footnotes
United States CFR, Title 49, Part 192 Pipeline Safety
(excluding those in tables and figures), shall not be considered
Regulations
5
as requirements of the standard.
2.4 UL Standard:
1.6 This standard does not purport to address all of the
UL 360 Standard for Liquid-Tight Flexible Steel Conduit
safety concerns, if any, associated with its use. It is the
3. Terminology
responsibility of the user of this standard to establish appro-
priate safety and health practices and to determine the
3.1 The gas industry terminology used in this specification
applicability of regulatory limitations prior to use.
is in accordance with ASME B31.8 or the United States CFR,
Title 49, Part 192, unless otherwise indicated.
2. Referenced Documents
3.1.1 pipe—used herein refers to both “pipe” and “tubing”
2
unless specifically stated otherwise.
2.1 ASTM Standards:
3.1.2 gas—used herein refers to any fuel gas unless specifi-
A513 Specification for Electric-Resistance-Welded Carbon
cally stated otherwise.
and Alloy Steel Mechanical Tubing
A53/A53M Specification for Pipe, Steel, Black and Hot-
3.2 Definitions—Definitions are in accordance with Termi-
Dipped, Zinc-Coated, Welded and Seamless
nology F412 unless otherwise specified. Abbreviations are in
accordance with Terminology D1600 unless otherwise speci-
fied.
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.60 on Gas.
3
Current edition approved Aug. 1, 2012. Published October 2012. Originally Available from American Society of Mechanical Engineers (ASME), ASME
approvedin2006.Lastpreviouseditionapprovedin2012asF2509–06(2012).DOI: International Headquarters, Three Park Ave., New York, NY 10016-5990, http://
10.1520/F2509-12. www.asme.org.
2 4
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from the Superintendent of Documents, U.S. Government Printing
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Office, Washington, DC 20402.
5
Standards volume information, refer to the standard’s Document Summary page on Available from Underwriters Laboratories (UL), 2600 N.W. Lake Rd., Camas,
the ASTM website. WA 98607-8542, http://www.ul.com.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2509−12
3.3 Definitions: 4.3 Moisture Seal:
3.3.1 anodeless riser, n—a type of mechanical fitting which 4.3.1 The riser casing shall include a bushing or seal at the
is designed to transport gas from underground polyethylene point where the PE pipe will enter the casing. This seal shall
piping to above-ground metallic piping. When properly protect the PE pipe from being damage
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2509 − 06 (Reapproved 2012) F2509 − 12 An American National Standard
Standard Specification for
Field-assembled Anodeless Riser Kits for Use on Outside
Diameter Controlled Polyethylene Gas Distribution Pipe and
1
Tubing
This standard is issued under the fixed designation F2509; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers requirements and test methods for field-assembled anodeless riser kits for use with outside
diameter controlled polyethylene gas distribution pipe and tubing in sizes through 2 IPS as specified in specification D2513.
1.2 The test methods described are not intended to be routine quality control tests.
1.3 This specification covers the types of field-assembled anodeless riser kits described in 3.3.2.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and not considered standard.
1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes
(excluding those in tables and figures), shall not be considered as requirements of the standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
A513 Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing
A53/A53M Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless
D638 Test Method for Tensile Properties of Plastics
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2513 Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
F412 Terminology Relating to Plastic Piping Systems
F1948 Specification for Metallic Mechanical Fittings for Use on Outside Diameter Controlled Thermoplastic Gas Distribution
Pipe and Tubing
F2897 Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing,
Fittings, Valves, and Appurtenances)
3
2.2 ASME Standards:
3
ASME Boiler and Pressure Vessel Code
4
ASME B1.20.1 Pipe Threads, General Purpose (Inch)
B31.8 Gas Transmission and Distribution Piping Systems
4
2.3 Federal Regulations:
United States CFR, Title 49, Part 192 Pipeline Safety Regulations
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.60 on Gas.
Current edition approved Feb. 1, 2012Aug. 1, 2012. Published February 2012October 2012. Originally approved in 2006. Last previous edition approved in 20062012
as F2509F2509–06(2012).–06. DOI: 10.1520/F2509-06R12.10.1520/F2509-12.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http://
www.asme.org.
4
Available from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2509 − 12
5
2.4 UL Standard:
UL 360 Standard for Liquid-Tight Flexible Steel Conduit
3. Terminology
3.1 The gas industry terminology used in this specification is in accordance with ASME B31.8 or the United States CFR, Title
49, Part 192, unless otherwise indicated.
3.1.1 pipe—used herein refers to both “pipe” and “tubing” unless specifically stated otherwise.
3.1.2 gas—used herein refers to any fuel gas unless specifically stated otherwise.
3.2 Definitions—Definitions are in accordance with Terminology F412 unless otherwise specified. Abbreviations are in
accordance with Terminology D1600 unless otherwise specified.
3.3 Definitions:
3.3.1 anodeless riser, n—a type of mechanical fitting which
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.