ASTM E377-08(2020)
(Practice)Standard Practice for Internal Temperature Measurements in Low-Conductivity Materials
Standard Practice for Internal Temperature Measurements in Low-Conductivity Materials
SIGNIFICANCE AND USE
2.1 Internal temperature measurements are made on both in-flight vehicles and on-ground test specimens; and, because of the importance of the temperature measurements to the design of various missile and spacecraft heat shields, it is essential that care be taken to minimize the sources of error in obtaining these measurements.
2.2 Over the past several years, the problems of using thermocouples to obtain accurate temperature measurements in low-conductivity specimens have been studied by various people to isolate the sources of error and to establish improved temperature measurement techniques. The major sources of error are listed in this document and recommended solutions to the problems are given.
SCOPE
1.1 This practice covers methods for instrumenting low-conductivity specimens for testing in an environment subject to rapid thermal changes such as produced by rocket motors, atmospheric re-entry, electric-arc plasma heaters, and so forth. Specifically, practices for bare-wire thermocouple instrumentation applicable to sheath-type thermocouples are discussed.
1.2 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units may be approximate.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: E377 − 08 (Reapproved 2020)
Standard Practice for
Internal Temperature Measurements in Low-Conductivity
1
Materials
This standard is issued under the fixed designation E377; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope error are listed in this document and recommended solutions to
the problems are given.
1.1 This practice covers methods for instrumenting low-
conductivityspecimensfortestinginanenvironmentsubjectto
3. General
rapid thermal changes such as produced by rocket motors,
3.1 Before proceeding to the major sources of error, it is
atmospheric re-entry, electric-arc plasma heaters, and so forth.
assumed that the reader is familiar with basic methods of
Specifically, practices for bare-wire thermocouple instrumen-
2
forming and using thermocouples , that is (1) electric welding
tation applicable to sheath-type thermocouples are discussed.
to form junctions, (2) maintaining cleanliness of junction area
1.2 The values stated in inch-pound units are to be regarded
and lead wires, (3) proper selection of thermocouple type and
as the standard. The metric equivalents of inch-pound units
size, corresponding to both the temperature range to be
may be approximate.
measured and the chemical compatibility with the
1.3 This standard does not purport to address all of the
environment, and (4) proper use of instrumentation for readout
safety concerns, if any, associated with its use. It is the
of thermocouple emf.
responsibility of the user of this standard to establish appro-
NOTE 1—Reader is referred toASTM MNL12 (1), and STP492 (2), as
priate safety, health, and environmental practices and deter-
well as Kinzie, P.A., Thermocouple Temperature Measurement (3), for
mine the applicability of regulatory limitations prior to use.
needed information.
1.4 This international standard was developed in accor-
3.2 The most important sources of error beyond the above
dance with internationally recognized principles on standard-
basic areas are the following:
ization established in the Decision on Principles for the
3.2.1 The thermal disturbance produced in the low-
Development of International Standards, Guides and Recom-
conductivitymaterialatthevicinityofthethermocouplesensor
mendations issued by the World Trade Organization Technical
hot junction due to the sensor size, configuration, and instal-
Barriers to Trade (TBT) Committee.
lation method.
3.2.2 Electrical shorting of lead wires due to the electrical
2. Significance and Use
conductivity of the virgin or charred ablation material, and
2.1 Internal temperature measurements are made on both
3.2.3 Thermocouple sensor hot junction location accuracy.
in-flight vehicles and on-ground test specimens; and, because
4. Thermal Disturbance at Vicinity of Thermocouple
of the importance of the temperature measurements to the
Sensor Hot Junction
design of various missile and spacecraft heat shields, it is
essential that care be taken to minimize the sources of error in
4.1 General—Ideally, to measure the true internal tempera-
obtaining these measurements.
ture of a solid body, it would be desirable not to have any
foreign substance present that would create a disturbance
2.2 Over the past several years, the problems of using
affecting the natural flow of heat in the body. Since it is
thermocouplestoobtainaccuratetemperaturemeasurementsin
physically impossible to exclude the temperature sensor from
low-conductivity specimens have been studied by various
theinternalconfinesofthebody,itisnecessarythatthethermal
people to isolate the sources of error and to establish improved
disturbanceintroducedbythesensorbeminimizedforaccurate
temperature measurement techniques. The major sources of
temperature measurements (See Refs (4-10)).
4.2 Thermocouple Junction Bead Diameter:
1 4.2.1 General—Excessively large junction beads result in
This practice is under the jurisdiction of ASTM Committee E21 on Space
Simulation andApplications of Space Technology and is the direct responsibility of lower than true temperature measurements in low-conductivity
Subcommittee E21.08 on Thermal Protection.
Current edition approved Nov. 1, 2020. Published December 2020. Originally
2
approvedin1968.Lastpreviouseditionapprovedin2015asE377 – 08(2015).DOI: ANSI MC96.1-1975. Temperature Measurement Thermocouples (Sponsor
10.1520/E0377-08R20. ISA).
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.