ASTM F2272-12
(Specification)Standard Specification for Paintball Markers
Standard Specification for Paintball Markers
ABSTRACT
This specification covers the performance requirements and test methods for paintball markers that propel paintballs using energy released from compressed air, compressed gas, or a combination of compressed air and gas. This does not cover non-recreational paintball markers such as those used in law enforcement, scientific, military or theatrical entities. All paintball markers should be supplied with appropriate literature, packaging, finish, design, and disabling device and shipped according to the specified shipping conditions. Under no circumstances should the cocking or pumping mechanism of a paintball marker cause a marker to discharge unintentionally while the marker is being cocked in accordance to instructions. Markers should not accidentally discharge when exposed to jolts strengths within the specified range.
SCOPE
1.1 This specification covers paintball markers, which propel a paintball by means of energy released by compressed air, compressed gas, or other means.
1.2 Limitations—This specification does not cover non-recreational paintball markers, for example, those used by law enforcement, scientific, military or theatrical entities.
1.3 The values stated in SI units are to be regarded as the standard; the inch-pound units in parentheses are provided for information only.
1.4 The following precautionary caveat pertains only to the test method portion, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F2272 −12 AnAmerican National Standard
Standard Specification for
1
Paintball Markers
This standard is issued under the fixed designation F2272; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.1.2 backstop—an object intended to stop a paintball.
3.1.3 barrel—that portion of a paintball marker through
1.1 This specification covers paintball markers, which pro-
which the paintball is discharged.
pel a paintball by means of energy released by compressed air,
compressed gas, or other means.
3.1.4 barrel blocking device—a muzzle blocking safety
device which, when properly installed, reduces the likelihood
1.2 Limitations—This specification does not cover non-
of an intact paintball discharging from the marker or leaving
recreational paintball markers, for example, those used by law
the confines of the barrel blocking device. The device is often
enforcement, scientific, military or theatrical entities.
referred to as a barrel plug or barrel bag.
1.3 The values stated in SI units are to be regarded as the
3.1.5 burst mode marker—a burst mode marker may dis-
standard; the inch-pound units in parentheses are provided for
charge two or more times per trigger cycle or may discharge
information only.
two or more times with the pull and release of the trigger.
1.4 The following precautionary caveat pertains only to the
3.1.6 caliber—the term used to refer to the size of a
test method portion, Section 8, of this specification. This
paintball projectile. Related to the measurement of the diam-
standard does not purport to address all of the safety concerns,
eter of the paintball as described in Specification F1979.
if any, associated with its use. It is the responsibility of the user
3.1.7 cautionary statement—thewarningoutlinedinSection
of this standard to establish appropriate safety and health
8 of this standard, which is to be placed on paintball markers,
practices and determine the applicability of regulatory require-
packaging and literature.
ments prior to use.
3.1.8 de-gassed, n—the state of the marker in which the
2. Referenced Documents
propellantsourceandanyinternalpropellanthasbeenremoved
2
from the marker.
2.1 ASTM Standards:
F1776 Specification for Eye Protective Devices for Paintball
3.1.9 disabling device—a device which, when activated,
Sports
disables a part of the paintball marker, usually the trigger, to
F1979 Specification for Paintballs Used in the Sport of
prevent unintentional discharges and must be released to allow
Paintball
the marker to be discharged by the movement of the trigger.
2.2 ANSI Standard:
The device is sometimes referred to as the “safety,” “safety
3
Z535.1 Safety Color Code
button,” or “safety lever.” An electronic on/off switch is
considered a disabling device when placing it in the “off”
3. Terminology
position renders the marker inoperable.
3.1 Definitions of Terms Specific to This Standard:
3.1.10 discharge mode—a mode that controls the number of
3.1.1 auto-trigger—a trigger which, when held in the dis-
paintballs discharged per trigger cycle.
charge position, will automatically cause the paintball marker
3.1.11 enhanced trigger mode marker—a paintball marker
to discharge when the pump or bolt action is manipulated.
that at some point discharges more than one paintball per
trigger cycle. This includes markers that “store” the number of
1
This specification is under the jurisdiction ofASTM Committee F08 on Sports
trigger pulls and discharge more than one paintball at some
Equipment, Playing Surfaces, and Facilities and is the direct responsibility of
point.
Subcommittee F08.24 on Paintball and Equipment.
Current edition approved July 1, 2012. Published August 2012. Originally
3.1.12 feed mechanism—amechanismthatstores,transports
approved in 2003. Last previous edition approved in 2011 as F2272 – 11. DOI:
and facilitates the loading of paintballs. It may be gravity,
10.1520/F2272-12.
mechanically or air assisted or automatic in its actions.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3.1.13 fully-automatic mode marker—a marker that dis-
Standards volume information, refer to the standard’s Document Summary page on
charges when the triggering device is actuated and continues to
the ASTM website.
3
discharge until the trigger returns to its reset or recycle
Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
4th Floor, New York, NY 10036. position.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, P
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:F2272–11 Designation: F2272 – 12
Standard Specification for
1
Paintball Markers
This standard is issued under the fixed designation F2272; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers paintball markers, which propel a paintball by means of energy released by compressed air,
compressed gas, or other means.
1.2 Limitations—This specification does not cover non-recreational paintball markers, for example, those used by law
enforcement, scientific, military or theatrical entities.
1.3 The values stated in SI units are to be regarded as the standard; the inch-pound units in parentheses are provided for
information only.
1.4 The following precautionary caveat pertains only to the test method portion, Section 8, of this specification. This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to
use.
2. Referenced Documents
2
2.1 ASTM Standards:
F1776 Specification for Eye Protective Devices for Paintball Sports
F1979 Specification for Paintballs Used in the Sport of Paintball
F2041Specification for Paintball Marker Warnings Specification for Paintballs Used in the Sport of Paintball
2.2 ANSI Standard:
3
Z535.1 Safety Color Code
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 auto-trigger—a trigger which, when held in the discharge position, will automatically cause the paintball marker to
discharge when the pump or bolt action is manipulated.
3.1.2 backstop—an object intended to stop a paintball.
3.1.3 barrel—that portion of a paintball marker through which the paintball is discharged.
3.1.4 barrel blocking device—a muzzle blocking safety device which, when properly installed, reduces the likelihood of an
intact paintball discharging from the marker or leaving the confines of the barrel blocking device. The device is often referred to
as a barrel plug or barrel bag.
3.1.5 burst mode marker—a burst mode marker may discharge two or more times per trigger cycle or may discharge two or
more times with the pull and release of the trigger.
3.1.6 caliber—the term used to refer to the size of a paintball projectile. Related to the measurement of the diameter of the
paintball as described in Specification F1979.
3.1.7 cautionary statement—the warning outlined in Section 8 of this standard and noted in Specification F2041, which is to
be placed on paintball markers, packaging and literature. of this standard, which is to be placed on paintball markers, packaging
and literature.
3.1.8 de-gassed, n—the state of the marker in which the propellant source and any internal propellant has been removed from
the marker.
3.1.9 disabling device—a device which, when activated, disables a part of the paintball marker, usually the trigger, to prevent
1
This specification is under the jurisdiction of ASTM Committee F08 on Sports Equipment and Facilities and is the direct responsibility of Subcommittee F08.24 on
Paintball and Equipment.
Current edition approved MayJuly 1, 2011.2012. Published June 2011.August 2012. Originally approved in 2003. Last previous edition approved in 20102011 as
F2272 – 101. DOI: 10.1520/F2272-112.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F2272 – 12
unintentional discharges and must be released to allow the marker to be discharged by the movement of the trigger. The device
is sometimes referred to as the “safety,” “safety button,” or “safety lever.” An electronic on/off switch is considered a disabling
device when placing it in the “off” position renders the marker inoperable.
3.1.10 discharge mode—a mode that controls the number of paintballs disc
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.